Question about 2001 Jeep Grand Cherokee

Where is locate the camshaft position sensor on 2001 jeep grand cherokee laredo limited 4.7 l

2 Answers

Anonymous

Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

Sniper:

An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

Governor:

An expert whose answer got voted for 20 times.
Expert
71 Answers

The camshaft position sensor is located inside the distributor. It is a hall effect swich, simply remove the distributor cap and the rotor and you can lift it out, unplug and replace.
Have fun but beware a bad crankshaft position sensor can cause a false cam sensor code to be set sometimes.
Good luck.

Posted on Dec 05, 2009

2 more comments
_-__-___-_ Mar 27, 2015

NOT ON ANY 2001, ITS NOT A 1995, SORRY. THERE IS NO DISTRIBUTOR, SORRY !
_-__-___-_ Mar 27, 2015

here it is part 3 is CMP part 1 is CKP (cam and crank) on right side front. see fSm real photo below.
_-__-___-_ Mar 27, 2015

note how close #3 is to cam>? note how close #3 is to cam>?
_-__-___-_ Mar 27, 2015

the 4L is a mod, from distributor block to cmp match.

jonwn00

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.
Contributor
2 Answers

The Cam Position sensor is located on the right head (passenger side) near the front just above the exhaust manifold

Posted on Mar 26, 2015

1 Related Answer

Richard Scordino

6982 Answers

SOURCE: Where is the camshaft sensor located on my 99 Jeep Grand Cherokee

If you still have a cap rotor and ignition wires, it's inside the distributor. If not, it is the part where the distributor used to be (center rear of the engine behind the intake manifold)

Posted on Feb 19, 2010

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1 Answer

I HAVE TO CHANGE OUT A CRANK SENSOR IN MY GRAND CHEROKEE.

Jeep Crank Sensor Replacement, P Codes P0351, P1391 ...

? 6:24
www.youtube.com/watch?v=7D0vUEDSwXo
May 12, 2013 - Uploaded by Robert DIY Replaced the crank sensor on this 2003 Jeep Grand Cherokee.... to replace my crankshaft position sensor on my 1998 grand cherokee laredo.

Jeep Crankshaft Position Sensor Replacement (CKP, CKPS ...

? 4:07
www.youtube.com/watch?v=1Ho5iAKQV00

Oct 27, 2013 - Uploaded by WeekendHandymen
hi , do you think if I replace crank sensor will solve the problem ,my jeep .... Where's the crankshaft located in 99 jeep grand Cherokee laredo .

Oct 24, 2015 | Cars & Trucks

1 Answer

Ok my 2001 Grand Cherokee Laredo wont stay in park

Transmission sticks in reverse- won't go into park. - JeepsUnlimited

www.jeepsunlimited.com/forums/showthread.php?...won-t-go-into-park
Jun 14, 2013 - 12 posts - ‎5 authors 2003 6 cyl 4x4 Grand Cherokee Laredo automatic- Occaionally, when shifting from REVERSE TO PARK, my Jeep will stay in reverse. Typically its ... '2001 WJ'4,0L'42RE'NV 242'380000 km'ECE Compliant' ??????????? ??? ...

2001 jeep grand Cherokee laredo - CarGurus

www.cargurus.com > Questions > Jeep > Grand Cherokee
CarGurusJan 27, 2014 - 2001 jeep grand Cherokee laredo - Just purchased a 2001 Jeep GrandCherokee Laredo and ... It starts in PARK sometimes and sometimes it won't and I have to start it in Neutral. ... Hatch shuts flush, but won't stay shut. help!

Oct 22, 2015 | Cars & Trucks

1 Answer

Code p0320 on 2002 jeep cherokee laredo?

P0320- Ignition/Distributor Engine Speed Input Circuit
Most likely a camshaft position sensor fault. You should have the vehicle diagnosed by a reputable repair facility.

Jan 29, 2013 | 2002 Jeep Grand Cherokee

1 Answer

Where is the camshaft position sensor located on a 06 jeep grand cherokee limited 4.7 l automatic ? ... also the crank position sensor

The CMP sensor engine contains a hall effect device called a sync signal generator to generate a fuel sync signal. This sync signal generator detects notches located on a tonewheel. The tonewheel (4) is located at the front of the camshaft for the right cylinder head (2). As the tonewheel rotates, the notches (1) pass through the sync signal generator. The pattern of the notches (viewed counter-clockwise from front of engine) is: 1 notch, 2 notches, 3 notches, 3 notches, 2 notches, 1 notch, 3 notches and 1 notch. The signal from the CMP sensor is used in conjunction with the crankshaft position sensor to differentiate between fuel injection and spark events. It is also used to synchronize the fuel injectors with their respective cylinders.

May 12, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Does my '97 jeep grand cherokee laredo have a camshaft position sensor?

what motor?

Sep 15, 2010 | 1997 Jeep Grand Cherokee

1 Answer

Where is the camshaft sensor located on 2002 jeep laredo 4.0 engine

most likely at the front of the engine above the water pump, directly over the camshaft.

Apr 30, 2010 | 2002 Jeep Grand Cherokee

1 Answer

Where is the camshaft sensor located on my 99 Jeep Grand Cherokee

If you still have a cap rotor and ignition wires, it's inside the distributor. If not, it is the part where the distributor used to be (center rear of the engine behind the intake manifold)

Feb 19, 2010 | 1999 Jeep Cherokee

1 Answer

Jeep is giving a code of p0340 which is telling me that I have a bad camshaft position sensor, where is the camshaft position sensor located on a 2000 Jeep grand cherokee with the 4.7l engine?

go to autozones website they have free diagrams

Dec 02, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Where is the APPS sensor located on the 2001 Gr Cherokee Laredo 4.0

APPS Accelerator Pedal Position Sensor is usually integrated to the pedal itself. If it has gone bad you have to replace the accelerator pedal assemble itself. 2 bolts/nuts and disconnect a wire harness.

Jul 19, 2009 | 2001 Jeep Grand Cherokee

2 Answers