Question about 2002 Chrysler Town & Country

1 Answer

2002 town and country...how do i find the trouble codes

How do i find the trouble codes where the odemeter is? i have read turn the key 3 times or hold down something and turn the key. which is it?

Posted by steveng25 on

Ad

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 11 Answers

Cycle the key three times. (turn from off to on)

Basically, it goes like this.

Insert key into ignition.
Turn forward to the 'on' position, the one just before cranking.
Turn back to off.
Turn forward to on again, and then back off.

Forward once more, and leave it there.

You should get a DTC (Diagnostic trouble code) that displays on the odometer.

If all is well, (or deemed well by the computer) you'll receive a message of 'done' instead of a PXXX (xxx=numbers) Code.

If you relay the code to me, I can help you further!

Posted on Nov 30, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Van will not fire turn key off and on several times and it starts


Use a gage and check proper fuel pressure. Cycling the key on and off several times before you crank it, allows the fuel pump to prime the system.
How long since a tune-up? Are there any applicable trouble codes?

Jun 09, 2016 | 2000 Chrysler Town & Country

1 Answer

2002 town and country the engine check light stays on all the time even with the key out. It has no codes


Sorry to say but from what i've seen over the years with Chrysler and knowing your exact decription of the problem that I have seen before! You need a new ECM/PCM ( Computer ) Sorry;(

Jul 31, 2011 | 2002 Chrysler Town & Country

1 Answer

I turned the key on and off 3 times on my 97 town and country and got a code of 1 2 4 3 5 5 and I cant find anything on the internet can you help


the 55 problem code is no more codes stored, or end of cycle. code 43 is problem in power module to logic module interface. code 12 is battery or computer recently disconnected. have a good day !!

Apr 09, 2011 | 1997 Chrysler Town & Country

1 Answer

How do you read the flashing check engine light codes on a 93 chrysler town & country?


Turn key on and off twice without starting engine. count flashes, their will be slight hesitation, make one digit after hesitation make second digit.(flashes 5 times hesitates flashes three times hesitates your code is 53) if it countiues to flash, its making second two digit code.

Jan 27, 2010 | 2005 Chrysler Town & Country

1 Answer

My chrysler 2002 town and country will not change gears. The RPMs stay at 2 or 3 when going 40 mph. What do I do?


I have the same vehicle, is your engine light on or flashing? Put your key in the ignition, turn back and forth 3 cycles of on off. End in the on position. If you have a 0700 code come up, your transmission is "done". Sounds like it is in "limp mode". Thats what happened to me. Had tranny overhauled, $1800.

Jan 21, 2010 | 2002 Chrysler Town & Country

1 Answer

Osd relay and fuel pump relay and acrelay all cliclk when teurn key engin will not start


run scanner for trouble codes, some auto parts store will do this for free, check for fuel at fuel rail , should halve valve stem type fitting, cover with rag and depress , you should have fuel if not open gas cap, turn key and listen for whirling sound in tank if not check fuel pump

Oct 03, 2009 | 2002 Chrysler Town & Country

1 Answer

Chrysler trouble code U110C on 2005 chrysler town


encrypted software ,dealer only----yes i know you are showing a reading but it doesnt mean anything or if it does it shows a different code .so your snap on or mac tools scanner is a waste of time and money.Nearly all new motors from 2005 are using encrypted software to stop general mechanics like me from working

Sep 12, 2009 | 2009 Chrysler Town and Country

2 Answers

What does the word donE mean in the instrument cluster


if its a dode you may have trigerd the on bored comp to run a dignostic

Mar 26, 2009 | 2002 Chrysler Town & Country

2 Answers

What is a code 66


I checked on my Mitchell's program and I don't show a code 66. Try to get the codes again. Turn the key on/off 3 times what watch the flashes. I can get you the information to you soon.

Jun 22, 2008 | 1997 Chrysler Town & Country

Not finding what you are looking for?
2002 Chrysler Town & Country Logo

281 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...