How do i install new headlamps - 1999 Pontiac Grand Am GT

Headlamp Removal & Installation To Remove:

1. Turn headlamp switch OFF.
   
   
2. Remove retaining ring screws.
3. Remove retaining ring from headlamp.
4. Remove headlamp from headlamp mounting bracket.
5. Disconnect electrical connector from headlamp.

To Install:

1. Connect electrical connector to headlamp.
2. Install headlamp to headlamp mounting bracket.
3. Install retaining ring to headlamp and install screws.

please rate, thanks.

SECTION 417-01: Exterior Lighting 2000 Focus Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/6/2003
Headlamp Assembly Removal
All vehicles

1. Remove the fender splash shield lower retaining screw.
   • Push the fender splash shield to one side.

1. Remove the headlamp assembly lower retaining bolt.

1. Remove the radiator grille.

Vehicles built up to 07/1999

1. Remove the headlamp assembly.
   • Disconnect the headlamp assembly electrical connector.

Vehicles built 07/1999 onwards

1. Remove the headlamp assembly.
   • Disconnect the headlamp assembly electrical connector.

Installation
Vehicles built up to 07/1999
NOTE: Procedure if there is a concern over the formation of condensation inside the plastic headlamp lens or if the plastic headlamp lens is split.
NOTE: It is normal for a small amount of condensation to form on the inside of the plastic headlamp lens, it will disappear when the headlamp is switched on. If the headlamp does NOT dry out after having been switched on for 15 minutes, check the build date of the headlamp. If the build date is between 01.08.98 and 30.09.98, install a new headlamp cover flap.
NOTE: If there is a concern, both headlamps must be removed. Defective headlamps must be renewed and reworking may be necessary. When the headlamp is installed, the number of mounting points must be reduced.

1. If the headlamp assembly is defective, install a new one.

1. NOTE: Sometimes the guide pin on the plastic headlamp lens is still present on a new headlamp assembly.
   Cut off the guide pin flush and de-burr as necessary.

1. Remove the headlamp levelling motor from the faulty headlamp assembly and install it on the new headlamp assembly. For additional information, refer to Headlamp Leveling Motor - Vehicles Built Up To: 10/2001 in this section.

1. NOTE: Sometimes there is no hole in the bracket of a new headlamp assembly.
   Do NOT install the retaining bolt any more.

All vehicles

1. NOTE: Fix the headlamp assembly in place using the locating pin.
   Install the headlamp assembly upper retaining bolts.
   • Connect the headlamp assembly electrical connector.

1. Install the radiator grille.

1. NOTE: Fix the headlamp assembly in place using the locating pin.
   Install the headlamp assembly lower retaining bolt.

1. Install the fender splash shield lower retaining screw.

1. Adjust the headlamps. For additional information, refer to Headlamp Adjustment - in this section. For additional information, refer to Headlamp Adjustment - Vehicles With: High Intensity Discharge Headlamps in this section.

this for aero headlamp, plastic lens. please rate.

SECTION 417-01: Exterior Lighting 1999 F-Super Duty 250-550 Workshop Manual
REMOVAL AND INSTALLATION Lamp Assembly —Headlamp, Aerodynamic Removal

1. NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
   Remove the headlamp assembly.
   1. Pull up and remove the two upper headlamp clips.
   1. Release the lower headlamp clip.
   1. Position the headlamp so the connector can be accessed.
   1. Disconnect the headlamp connector.

Installation

1. Install the headlamp assembly.
   1. Position the headlamp assembly.
   1. Connect the headlamp connector.
   1. Install the lower headlamp clip.
   1. Install the two upper headlamp clips.
      • If necessary, adjust the headlamps. For additional information, refer to Headlamp Adjustment—Photometric Aiming or Headlamp Adjustment—Screen Method Aiming in this section.
      

SECTION 417-01: Exterior Lighting 2002 Lincoln LS Workshop Manual REMOVAL AND INSTALLATION Lamp Assembly —Headlamp Removal and Installation
WARNING: The halogen fog lamp bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope.
NOTE: The headlamp bulb should not be removed from the headlamp assembly until just before a replacement bulb is installed. Removing the bolt for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp assembly where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed.

1. NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
   Release the ambient air temperature sensor.

1. Remove the radiator grille opening cover at the top shelf of the bumper.

1. Remove the radiator upper sight shield.
   1. Remove the pin-type retainers.
   1. Remove the radiator upper sight shield.

1. Position the headlamp assembly for removal.
   1. Remove the three bolts.
   1. Position the headlamp assembly for removal.
   • Disconnect the electrical connectors and remove the headlamp assembly.

1. To install, reverse the removal procedure.
   • If necessary, install new bulbs.
   

You will need basic hand tools.

Headlamp Bulb: Service and Repair
HEADLAMP BULB REPLACEMENT (EQUINOX)
REMOVAL PROCEDURE
1. Open the hood.
2. Remove the fascia to tie bar push-in retainers (1).
3. Gently pull the top of the fascia assembly several inches away from the vehicle to release the radiator grille strap from the headlamp.
4. Place a piece of tape over the radiator grille strap to headlamp retaining clip to prevent scratching of the headlamp lens.
5. Remove the headlamp bolts (1, 2).
6. Pull gently on the bottom outboard corner of the headlamp to disengage the lower rear headlamp retainer.
7. Remove the headlamp from the vehicle.
INSTALLATION PROCEDURE
1. Position the headlamp into the headlamp opening.
2. Push the headlamp back into position until the lower rear retainer is fully engaged.
3. NOTE: Refer to Fastener Notice.
Install the headlamp bolts (1, 2)
Tighten the headlamp bolts to 2.5 N.m (22 lb in).
4. Remove the tape from the radiator grille strap retainer.
5. Position the fascia assembly and engage the radiator grille strap retainer into the headlamp.
6. Install the fascia to tie bar push-in retainers (1).
7. Close the hood.
8. Check and adjust the front headlamp aim after the headlamp has been reinstalled. Refer to Headlamp Aiming.

Headlights REMOVAL & INSTALLATION Non-European Style

1. Remove the headlamp trim panel attaching screws.

Fig. 1: Remove the headlamp trim panel attaching screws

Remove the headlamp bulb retaining screws. Do not touch the two headlamp aiming screws, (at the top and side of the retaining ring), or the headlamp aim will have to be readjusted.
Fig. 2: Remove the headlamp trim panel assembly from it's mounting location Using a screwdriver, remove the retaining ring screws.

Once the retaining ring screws are removed, the ring can be pulled away

Pull the bulb and ring forward then separate them. Unplug the electrical connector from the rear of the bulb.
Fig. 5: Pull the bulb out and unplug the electrical connector

1. To install:
2. Plug the new bulb into the electrical connector.
3. Install the bulb into the retaining ring and install the ring and bulb.
4. Install the trim panel.

If you would like the photos (I can't post them here...too large of files) email me at [email protected]

SECTION 417-01: Exterior Lighting 2001 Villager Workshop Manual REMOVAL AND INSTALLATION Bulb —Headlamp Removal

1. WARNING: The halogen bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Grasp the bulb only by its base. Avoid touching the glass envelope.
   NOTE: The headlamp bulb should not be removed from the headlamp until just before a replacement bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp.
   NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
   Remove the headlamp bulb.
   1. Disconnect the electrical connector.
   1. Remove the headlamp bulb retainer by rotating it counterclockwise about one-eighth of a turn.
   1. Remove the headlamp bulb.

Installation

1. Install the headlamp bulb.
   1. Install the headlamp bulb.
   1. Install the headlamp bulb retainer by rotating it clockwise about one-eighth of a turn.
   1. Connect the electrical connector.

------
go here for villager help

http://autos.groups.yahoo.com/group/villagerquest/

REMOVE OR DISCONNECT

• Make sure the headlamp switch is off.

1. Retaining ring screws from the retaining ring.
2. Retaining ring from the headlamp.
3. Headlamp from the headlamp mounting bracket.
4. Electrical connector from the headlamp.

INSTALL OR CONNECT

1. Electrical connector to the headlamp.
2. Headlamp to the headlamp mounting bracket.
3. Retaining ring to the headlamp.
4. Retaining ring screws to the retaining ring

sorry, i only have 94 whcih is probably different. Hope it helps at least some.

Section 17-01: Lighting, Exterior 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Headlamp Assembly WARNING: THE REPLACEABLE HALOGEN HEADLAMP BULB CONTAINS GAS UNDER PRESSURE. THE BULB MAY SHATTER IF THE GLASS ENVELOPE IS SCRATCHED OR THE BULB IS DROPPED. HANDLE BULB CAREFULLY. GRASP BULB ONLY BY ITS PLASTIC BASE. AVOID TOUCHING GLASS ENVELOPE. KEEP BULB OUT OF REACH OF CHILDREN.
Removal and Installation

1. Place the headlamp switch (11654) in the OFF position.

1. Remove the electrical connector from the miniature bulb (13466) by pulling it rearward.

1. Remove three nut and washer assemblies from the rear of the headlamp (13008) .

1. Remove the headlamp by pushing forward on the headlamp bulb and retainer (13N021) assembly. For ease of removal, it may be necessary to loosen the attachments of the adjacent parking lamp (13200) and cornering lamp assemblies.

1. Remove the three clips attaching the headlamp to the headlamp bulb retainer (13N019) by prying them out from the base using a flat-blade screwdriver. This completes the removal of the headlamp . Save the clips for the installation of the new headlamp .

1. To install the aerodynamic headlamp , ensure that the black rubber shield is securely crimped to the headlamp , then reverse Removal procedure.

1. After headlamp installation, check headlamp aim and adjust as necessary as outlined under Adjustments.

1. Turn headlamp switch on and check for proper operation.
   
   
   
   
   Item Part Number Description 1 13200 Parking Lamp Assy 2 14290 Headlamp Dash Panel Junction Wire 3A N621906-S301 Nut (2 Req'd) 4 13A093 Headlamp Adjustment Screw and Nut Assy 5 13008 Headlamp Bulb A Tighten to 4.4-6.4 Nm (39-57 Lb-In)

1. Disconnect and isolate the battery negative cable.
2. Remove the headlamp cover TOP
   1. Remove the mounting fasteners.
   2. Disconnect the headlamp unit electrical connector BACK
   3. Separate the headlamp from vehicle.CAUTION: Do not touch the bulb glass with fingers or other oily surfaces. Reduced bulb life will result.
      
      NOTE: If installing a new headlamp unit, transfer all the wiring, bulbs, and sockets to the new unit.
      
      
      1. Install all of the bulb sockets in headlamp .
      2. Position the headlamp on the vehicle.
      3. Connect the electrical connector .
      4. Push the headlamp inward to secure into position.
      5. Install mounting fasteners
      6. Install cover over headlamp.
      7. Connect battery negative cable