How do you replace the right rear window? - 2002 Chevrolet Silverado

Did the switch work before replaced battery ? 2008 CTS ? Cadillac ? These switches are inputs to a control module , DDM - driver door module . a computer of sorts . A lot of thing's can go wrong with these systems , broken power or ground circuits inside the rubber boot from the body to the driver door . Communication problems between control modules etc... Plus the power windows don't use fuse's , has a circuit breaker for front windows - PWR/WNDW circuit breaker 25 amp located in the fuse box under the back seat , Fuse's are used for rear windows - two 15 amp fuse's LT/REAR an rear ,both are in the rear fuse box under back seat. These rear windows are controlled by the BCM - body control module .

The power windows system consists of the following components:
• Driver door module (DDM)--GMLAN device that receives and transmits messages and signals for window functionality. The DDM contains the driver door switch (DDS) which is integrated into the module. The DDS contains the driver, front passenger, RR and LR window and window lockout switches.
• Passenger front door module (PDM)--GMLAN device that receives and transmits messages and signals for window functionality. The PDM contains the front passenger door switch (PDS) which is integrated into the PDM. The PDS contains the front passenger window switch.
• Left rear power window switch--Provides switched voltage and ground window switch signals to the left rear window motor for left rear passenger window operation
• Right rear power window switch--Provides switched voltage and ground window switch signals to the right rear window motor for right passenger window operation
• Left front power window motor--Contains position sensors and a module that receives signals from the DDM and provides a status signal to the DDM
• Right front power window motor--Contains position sensors and a module that receives signals from the PDM and provides a status signal to the PDM
• Left rear power window motor--Contains position sensors and a module that receives signals from the left rear power window switch
• Right rear power window motor--Contains position sensors and a module that receives signals from the right rear power window switch
• DRIVER DR MOD fuse (15-amp)
• PDM fuse (15-amp)
• PWR WNDW Circuit Breaker (25-amp) -- front
• LT/REAR/WNDW fuse (15-amp) -- rear
• REAR/WNDW fuse (15-amp) -- rear


Power Window Operation
The driver and front passenger doors are equipped with power window motors that contains its own module. Each power window motor receives a hot at all times battery supply voltage and constant ground source. When the right front passenger window switch on the DDS is activated to the up or down position, the DDM will interpret the signal and send a GMLAN serial data message to the PDM. Upon receipt of the message, the PDM will send a signal to the front passenger window motor module on the GMLIN serial data circuit. The window motor module will then supply battery voltage and ground to the window motor to drive the window motor to the up or down position.
The DDM communicates via the GMLAN serial data circuit with the body control module (BCM) to control the rear window functions from the driver master window switch. The BCM is hard wired to each rear power window switch with circuits for window up, window down, and an enable circuit. The rear window switches contain internal logic that when supplied with voltage from the BCM over the enable circuit will driver the appropriate window in the direction commanded.
The rear power window switches are supplied with battery voltage from individual right and left WNDW fuses located in the rear fuse block. When a rear power window switch is activated to the DOWN position, voltage is applied to the motor down circuit and the motor up circuit serves as the path to ground. The window motor will drive in the downward direction until the switch is released or the window has fully opened. When the window switch is activated to the UP position, voltage is applied to the motor up circuit and the motor down circuit serves as the path to ground. Ground for the left rear power window switch is supplied at G200 and the right rear power window switch receives ground at G201.

The power locks work the same .

After replacing the driver door switch (DDS) or passenger door switch (PDS), perform the programing procedure.

If you don't know any of what i posted your best bet , have a qualified repair shop check it out .

Rear Quarter Window Actuator - Right (A20)
Behind the right rear interior body panel
Rear Quarter Window Actuator - Left (A20)
Behind the left rear interior body panel
Rear Quarter Window Inoperative

1

Did you review the rear quarter window description and operation?
Go to Step 2
Go to Symptoms - Body Rear End

2

Verify that the rear quarter windows are inoperative.
Do the rear quarter windows operate normally?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
Go to Step 3

3

Are both rear quarter windows inoperative?
Go to Step 4 yes
Go to Step 6 no

4

1. Turn OFF the ignition.
2. Disconnect the rear quarter window switch.
3. Turn ON the ignition, with the engine OFF.
4. Probe the accessory voltage circuit of the rear quarter window switch harness connector with a test lamp that is connected to a good ground.

Does the test lamp illuminate?
yes Go to Step 5
no Go to Step 7

5

Connect a test lamp between the accessory voltage circuit of the rear quarter window switch harness connector and the ground circuit of the rear quarter window switch harness connector.
Does the test lamp illuminate?
Go to Step 8
Go to Step 10

6

1. Turn OFF the ignition.
2. Disconnect the appropriate rear quarter window actuator.
3. Turn ON the ignition, with the engine OFF.
4. Connect a test lamp between the power window motor rear vents open control circuit of the rear quarter window actuator harness connector and the power window motor rear vents close control circuit of the rear quarter window actuator harness connector.
5. Activate the rear quarter window switch to the Open and Close positions.

Does the test lamp illuminate?
yes Go to Step 9
no Go to Step 11

6

1. Turn OFF the ignition.
2. Disconnect the appropriate rear quarter window actuator.
3. Turn ON the ignition, with the engine OFF.
4. Connect a test lamp between the power window motor rear vents open control circuit of the rear quarter window actuator harness connector and the power window motor rear vents close control circuit of the rear quarter window actuator harness connector.
5. Activate the rear quarter window switch to the Open and Close positions.

Does the test lamp illuminate?
yes Go to Step 9
no Go to Step 11

7

Test the accessory voltage circuit for an open or a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 14
Go to Retained Accessory Power (RAP) Inoperative in Computer/Integrating Systems

8

Inspect for poor connections at the harness connector of the rear quarter window switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
yes Go to Step 14
no Go to Step 12

9

Inspect for poor connections at the harness connector of the appropriate rear quarter window actuator. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
yes Go to Step 14
no Go to Step 13

10

Repair the open in the ground circuit of the rear quarter window switch. Refer to Wiring Repairs and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 14
--

11

Repair the open in the appropriate power window motor rear vents control circuit. Refer to Wiring Repairs and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 14
--

12

Replace the rear quarter window switch. Refer to Quarter Window Switch Replacement .
Did you complete the replacement?
Go to Step 14
--

13

Replace the appropriate rear quarter window actuator. Refer to Body Side Window Actuator Replacement .
Did you complete the replacement?
Go to Step 14
--

14

Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

Put some silicone spray or dry lube in the window frame where the glass runs and this will free up the window and take the load off the motor.
All "Henry"window winder switches are a problem they don't last lone at all. I have replaced my Ford winder switches about every 18months to 2 years. They are a money maker for Ford Motor Coy

corrosion in the switch from water driping on it while window is down. try cleaning connection and switch if doesn't work replace swich.

could be the window switch or the fuse is blown or the wires r shorted to the window motor. did u check for power and ground at the motor before u replaced it?

The power window regulator is broken. It will need to be replaced to fix this problem. Click on the link below to get a replacement:

http://www.rockauto.com/catalog/raframecatalog.php?carcode=1362619&parttype=1516&a=FRc1362619k377098

Most likely you have left the windows on that side of the car open a bitand water has cased some corrsion on the connections. You need to replace the switch if removing and cleaning connection does not work.

The switch block can be pried out of the console with a screwdriver applied to the rear end of the block. Individual switches are not replaceable; the block is replaced as a whole. The lines connect to the block in a connector plug. Jumping them in a convertible is easier than in the other cars, as there is no lockout for the rear windows in the centre console switch. Your best option is to bite the bullet and replace the switch block either from an on-line source such as eEuroparts for about $200 US, or a wrecker.

Lines 18 & 19 are for the left front window,
lines 6 & 7 are for the right front window,
lines 13 & 14 are for the left rear,
lines1 & 2 are for the right rear, and
line 9 is the lock-out for the rear windows; I believe positive voltage applied constantly to this line locks out the rear windows, so leaving it un-powered won't hurt.

Polarity determines whether the window goes up or down; a trial and error situation. Use this info to get them up, then replace the switch block!

the rear side window vent motor is bad, u need to replaced it...common on these vans...i hope its the left rear and not the right....right is a little more difficult re installing due to the rear a/c ducts

Without proper electrical diagnostic equipment and based on the very through description that you gave I would suggest getting a new switch. I say a new switch because on the drivers side the switch is one giant junction block. I have the same vehicle and had my door panel off for some locking issues.

I have attached a link to Ford Direct. The part that you are looking for is Window switch, explorer, 4 door, right

http://www.forddirectonline.com/partlocator/index.cfm?action=getLocator&siteid=214462&chapter=DP2028&appSectionid=3&groupid=10005&subgroupid=20061&componentid=62141&make=10&model=Explorer&year=2000&catalogid=1