Question about 1987 Dodge Ram Maxivan

Open Question

Replace ignition switch 1987 dodge ram 250 van with tilt steering

Posted by abynum62 on

  • abynum62 Nov 06, 2009

    replce ignition switch

×

Ad

5 Related Answers

Anonymous

  • 3 Answers

SOURCE: 1991 dodge ram 250 van 318 engine won't start

ALWAYS CHECK THE GROUND ON A DODGE

Posted on Nov 16, 2008


Anonymous

  • 30 Answers

SOURCE: how do I remove and replace the steering column of 1992 ram 250 v

remove coupling from top of steering rack ( make sure you mark postition of coupling first with centre punch so the replacement will be in the same position)
remove covers from steering column and ignition + anything else attached to column. good luck

Posted on Jul 28, 2009

Ad
motor1258

Mike Butler

  • 6674 Answers

SOURCE: ive changed the ignition switch and checked the

Do you have ballast resistor on firewall by chance? ( 2"x 4" ceramic like block,usually held with 1 bolt in center)

Posted on Aug 02, 2009

Rod

  • 19 Answers

SOURCE: I need to remove an ignition switch from a 1987 Dodge van

1. Check the Motors, or similar manual at your public library for your van or enter your problem in your internet search engine.

Posted on Oct 30, 2009

Anonymous

  • 1 Answer

SOURCE: 1987 dodge ram van STEERING COLUMN

to whom this may concern did you find a steering column. Are you replacing it in a 1987 dodge pick-up

Posted on Feb 12, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove commutatuer switch on 2003 dodge van


I think he is referring to the ignition switch. I think Switch Translates to French as commutator or interrupter. After removing the steering column covers, You will need toremove the lock cylinder. Once that is out of the way you will need to unplug the clock spring connector for the airbag. Than if you have tilt wheel you will need to remove the tilt lever. Non tilt wheel will have a bracket that needs to be removed. You will than be able to access the screws that hold the ignition switch in place.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Sep 01, 2012 | Dodge Caravan Cars & Trucks

1 Answer

I have a 1987 Ford F 250. The ignition is really hard to turn over. It will start and run fine if I have the strength to turn it over. Why???


This is due to a bad ingition switch on the column or the igniton cylinder lock, you will need to remove the lock and see if it spins freely off the linkage for the switch ,90% of the time its the key cylinder, some off these fords are easy to replace the lock and remove it, there a small hole at the bottom of the column where the lock sits, if you look under the lock there should be a small holel insert a pick into the hole and push lightly then turn key slowly you will feel pic go in this is releaseing the lock tab then the lock will slide out, hold in hand and see if it turns freely if not replace it. hope this helps. just did a little research and this applies only to tilt wheel, if you dont have tilt then steering wheel and the plate must be removed here a diagram to show you the pin for a truck without tilt.johnjohn2_31.gif

Dec 08, 2010 | 1987 Ford F 250

1 Answer

The only way my headlights in my 1999 dodge ram worked was if i did Tilt Wheel know they dont come on at all...went to a dodge dealer and the answer i got was NEVER HEARD OF THAT....Ya right!can any shed...


If tilting the wheel turned the headlights on, it sounds like there's a problem with the ignition switch. Or if the headlight switch is a stalk on the steering column, possibly a fault somewhere in that switch or the wiring to it. First thing to do is find the headlight fuses and see if you have power on both sides of the fuse with the key on. If you don't, i would take the steering column covers off and look for a broken wire or burnt connector at the ignition switch.

Jul 06, 2010 | 1999 Dodge Ram

1 Answer

I need to remove an ignition switch from a 1987 Dodge van


1. Check the Motors, or similar manual at your public library for your van or enter your problem in your internet search engine.

Oct 30, 2009 | 1987 Dodge Ram Maxivan

1 Answer

How do I remove and replace the steering column of 1992 ram 250 v


remove coupling from top of steering rack ( make sure you mark postition of coupling first with centre punch so the replacement will be in the same position)
remove covers from steering column and ignition + anything else attached to column. good luck

Jul 27, 2009 | 1992 Dodge Ram

2 Answers

1987 dodge ram van STEERING COLUMN


to whom this may concern did you find a steering column. Are you replacing it in a 1987 dodge pick-up

Apr 23, 2009 | 1987 Dodge Ram Wagon B250

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

335 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14850 Answers

Mike

Level 3 Expert

4369 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...