Question about 2001 Isuzu Trooper

1 Answer

Where is the location of the egr valve on a 2001 isuzu trooper

Posted by emaildougnow on

Ad

1 Answer

Steve Hurc

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Isuzu Master
  • 459 Answers

On petrol V6 engine its right rear side of inlet manifold(left side when looking into engine bay) see pics. below
diesel its on inlet manifold left side middle section of manifold

where is the location of the egr valve on a 2001 - eb59265.jpg where is the location of the egr valve on a 2001 - 2736ba4.jpg data-src="/uploads/images/2736ba4.jpg" alt="2736ba4.jpg" class="h_mi" />

Posted on Nov 02, 2009

Ad

4 Related Answers

blueextc3221

blueextc3221

  • 15935 Answers

SOURCE: where is the egr valve for a 1999 isuzu trooper?

The EGR valve is a cylindrical unit above the engine. It would be behind the throttle body.
It will have a cable connected to it. Unplug the cable.
There two bolts. Simply remove.
An that is all there is to it.
Simply put the new EGR valve in its place, screw in the bolts and reconnect the cable.
Make sure to see a gasket. The gasket can stick to either the EGR valve or the throttle body. It does come off easily but since it is metallic, it looks like it part of the throttle/egr valve.

74cc5a2.jpgThanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Posted on Jul 03, 2009

Ad
emissionwiz

Marvin

  • 85239 Answers

SOURCE: Oxygen Sensor on '99 Isuzu Trooper

The O2 sensor is on the engine side (up stream) before the catalytic converter in the exhaust pipe, it is barrel shaped about the size of a jumbo magic marker.

Posted on Sep 30, 2008

kel1guy2002

Kelly

  • 3740 Answers

SOURCE: How to clean EGR valve passages in 1993 Isuzu Trooper DOHC V6

You have to the EGR valve (sometimes the Intake manifold to EGR Vlalve line also). After you remove it take a drill bit the about 20 % smaller than the actual hole of the outlet side and rotate the drill bit with your hand to dig out the carbon. Aditionally the line coming from the intake manifold to the EGR valve will clog near the connection to the EGR valve. I use either a single piece of copper wire or the wire that you would use to tie ribar together to clean the line. When your done cleaning take a piece of vacuum line and connect it to the diaphram side and **** on it... then plug the line well with your thumb. Grasp the valve and blow thru it... Air should blow thru it freely. Remove your thumb from the vacuum line and try blowing again.. No air should pass thru the valve.
Then reinstall the valve and start the vehicle with the vacuum line disconnected (but blocked off) Use another piece of vacuum line connected to the diaphram again and **** on the line.. The vehicle should die or run really bad. If it does this then you cleaned it correctly.

Posted on Jan 20, 2010

honeymokey

honeymokey

  • 3113 Answers

SOURCE: 1998 isuzu trooper egr.valve how

The passages in the manifold are stopped up. You will need something like an old speedo cable and a drill to fix.

Posted on May 11, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are codes p0401 and p0300 mean on a 2000 isuzu trooper


P0401 is EGR problem
P0300 is a cylinder 3 misfire.
Replace EGR valve and do a full tune-up.

Mar 19, 2014 | 2000 Isuzu Trooper

2 Answers

2001 isuzu trooper code 1340


Hello,
A 1340 error code for your Isuzu Trooper means that the engine is experiencing a "Camshaft Position Sensor B Circuit Malfunction" which would mean the computer isn't exactly sure where the camshaft is located in it's rotation. If the issue is intermittent then look for a broken wire, if it's solid then the sensor needs replacing!
Good Luck & please rate this solution!

Feb 04, 2012 | 2001 Isuzu Rodeo

1 Answer

I have a code P1860 and code P0405 in my 2001 isuzu trooper


Code p0405 is for faulty EGR vave od some of the pipe/lines going in or out of EGR valve/system hase broke, leaks or fall of. Or egr valve is dirty and stuck. Check EGR valvle!

Sep 09, 2010 | 2001 Isuzu Trooper

1 Answer

2001 Isuzu Trooper PO405 code


The throttle body is coated with a sludge resistant material. If you cleaned it all out you are actually hurting your engines performance, because the throttle body resists sludge which in turn protects your throttle plate and bore. You may want to check your egr vacuum regulator, for the cause of your problem.

Jul 05, 2010 | 2001 Isuzu Trooper

1 Answer

I keep losing power as in sputtering and have been told it may be the egr valve, is this possible?


it may be the problem but if you havent done it already you may want to change the plugs and wires first before buying an expensive egr valve

Feb 09, 2010 | 2001 Isuzu Trooper

2 Answers

Diy egr valve replacement on my 02 Trooper


you need to provide more info on engine size 2 or 4 wheel drive to locate part for you to give time frame for difficulty and need to know how to test system in order to find is working properly accorking to labor hour is going to be less then an hour on the limited edition.

Jan 07, 2010 | 2002 Isuzu Trooper

2 Answers

Have a code p0401 how do u fix it , I know it has something to do with the egr system but I,m not sure where its located on my trooper, engine size is 3.5 v6


I have a 2000 Isuzu Trooper that had a PO401 code that would reset and then 2 miles later the light was on again - I found if you remove the EGR valve and start the engine that the engine should idle rough - If it doesnt and you have vacumn at the intake port spray carb cleaner down the port slowly and see how long it takes for the engine to run rough - Keep spraying till the engine dies and spray some more down the passage and let the engine set for 5 minutes and then restart the engine - it will run rough at first but clear out - you should be able to feel the engine RPM change when you put your finger over the intake vaccumn port for the egr - If not then repeat the cleaning method again - If you do feel the rpm change then put the egr valve back on and clear the code and run your drive cycle to see if it is fixed.

Dec 17, 2009 | 2001 Isuzu Trooper

1 Answer

Oxygen Sensor on '99 Isuzu Trooper


The O2 sensor is on the engine side (up stream) before the catalytic converter in the exhaust pipe, it is barrel shaped about the size of a jumbo magic marker.

Sep 30, 2008 | 1999 Isuzu Trooper

Not finding what you are looking for?
2001 Isuzu Trooper Logo

Related Topics:

1,107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14846 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...