Question about 2002 Hyundai XG350

1 Answer

2002 XG 350. License plate bulb out. How do I pull bulb, wiring is too tight. Thanks Joe B

Posted by Jobiesi on

Ad

1 Answer

PAULH

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

2002 HYUNDIA XL 350, LIC. PLATE BLUBS CAN NOT GET ASSEMBLY DOWN TO REPLACE BLUBS, DUE TO THE FACT THE WIRES ARE TOO SHORT TO PULL UNIT DOWN. ANYH IDEAS?

Posted on Jan 12, 2014

Ad

5 Related Answers

g68mike

  • 21 Answers

SOURCE: how do i change the light bulbs that illuminate the license plate?

If the car is a hatch back, there is a access panel in the middle of the interior panel, you should be able to access them from there, its a tight squeeze. If its just a four door you can access them from inside the trunk.

Posted on Jul 02, 2008

Ad

Anonymous

  • 217 Answers

SOURCE: License Plate bulbs

they should be reachable from under/behind the bumper

Posted on Jul 11, 2008

Anonymous

  • 350 Answers

SOURCE: 2002 Hyundai XG 350L Check Engine Light w/o a code

hi the check light has a short could be expensive to fix or not trouble nowadays electronic componts are tempermental so have you got your code for your radio as the soultion to the problem could be as simple as disconnecting your battery for 10 minutes and reconnect this will reset your ecu unit and any abnormall glitchs in the computer trouble is you will lose your codes for the radio this is something that is rare but i have come across before running the car without the check light working only tells you if the emmissions system is working or not the car will run fine as it as a back up system so if the cars not giving you any problems it will be ok but this should work if not then check the wiring from the light and the ecu yates210456

Posted on Sep 30, 2008

Anonymous

  • 160 Answers

SOURCE: Change License Plate Light Bulb

you should be able to get to thru the trunk

Posted on Dec 10, 2008

Anonymous

  • 98 Answers

SOURCE: how do you change the license plate light bulb

OK>>> it is very cold here, but nonetheless..I went outside to check on my Oldsmobile for your benefit....On mine (I can't guarantee it is the same for all of the vehicles listed above). If you are looking at the license plate, LOOK UP and you should see the bulb and whatever encasing is there. Mine is in a tube and it is attached with (2) mini bolts that will need to come out first, then it just looks like a simple matter of disconnecting the electrical plug, taking out the old bulb and putting the new one in. I hope this helps someone....

Posted on Feb 23, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

License plate lights arent working


You didn't forget to pull the headlight switch to check them? That's odd, usually license plate lights are spliced in from the tail light circuit.
There may be a separate ground for the license lights-if so, should be right nearby the bulbs. Use a test light or voltmeter and make sure fuse 22 has power. You could also check the sockets for power. If you have power to the socket and new bulbs don't work, it would be a grounding problem.

Jul 09, 2013 | Cars & Trucks

1 Answer

How do you change the rear license plate light bulbs???


First look under when your license plate lights are and you will see 2 phllips headed screws remove those screws and the license plate light assembly will drop out of the bottom of the trunk, simply twist the blub to unlock it from the light housing pull the bulb straight out of the socket replace it with a new bulb and the installation is the reverse of the removal.

Dec 06, 2010 | 2002 Jeep Grand Cherokee

1 Answer

I need to replace the bulbs above the license plate on my 2002 eldorado how do you replace them....get at the old bulbs


Hello: Remove the license plate, then remove the screws on the chrome piece behind the license plate and the you can access the bulbs.

Nov 24, 2010 | 1999 Cadillac Eldorado

1 Answer

How to replace license plate light on a 2002 buick lesabre


Hi. Remove the retaining screws from the license plate light assembly with a Phillips screwdriver. There are two screws on each side of the lens assembly.

Pull the light assembly cover down out of the way to gain access to the bulbs. Twist the bulb socket counterclockwise to remove it from the assembly and pull it straight out. Pull the bulb out of the socket.

Push the new bulb straight into the socket. Replace the bulb and socket inside the light assembly and turn it clockwise to secure it.

Replace the assembly cover and secure it with the retaining screws. Tighten the screws with a Phillips screwdriver. Turn on the lights to test your new bulbs.
Take care

Aug 04, 2010 | 2002 Buick LeSabre

1 Answer

The license plate lights wont come on new bulbs


Pull the bulbs and check to see if you have voltage going to the socket. If not, check wiring, and check for sany damage to wiring, harnesses, etc.

Apr 17, 2010 | 2004 Hyundai Elantra

1 Answer

1999 Dodge Neon rear license Plate bulb


LICENSE PLATE LAMP BULB
REMOVAL
  1. Remove screws attaching license plate lamp to rear bumper
  2. Remove lamp from bumper.
  3. Remove bulb socket from lamp.
  4. Pull bulb from socket.

INSTALLATION
  1. Install bulb into socket.
  2. Install bulb socket into lamp.
  3. Place lamp in position.
  4. Install screws attaching license plate lamp to rear bumper.

Oct 08, 2009 | 1999 Dodge Neon

1 Answer

How do i replace the license plate bulbs on a 2002 chev trailblazer


There will be one or two screws or push pins securing the lense. Remove the screw or pin and pull the lense out. Twist the bulb socket and pull out the bulb. If you haven't already purchased the replacement bulbs, it will use a 194 bulb.

Apr 17, 2009 | 2002 Chevrolet TrailBlazer

4 Answers

Replacing license plate lights on Chevy Trailblazer


I just had the same problem. I took the cover off, saw the white bulb base, twisted it to take it out, but it popped back inside the door. I got it out, but it wouldn't pull through, so I twisted it back in place and went to Autozone to get new bulb. Once I saw the new bulb, it was obvious, just the bulb itself pulls out. There's so little room to work, I couldn't get it with just my fingers - - maybe rubber gloves would have worked, but I used pliers, lightly, wiggled it a little and it popped right out. I had a similar issue once with the taillight bulb and had to break the bulb and then grip the remaining filament wires with pliers to get it out, so that was my backup plan, just in case.

Hope this helps others.

Apr 14, 2009 | 2002 Chevrolet TrailBlazer

1 Answer

2002 license plate bulbs


its real simple look at the license plates then look up you will see 2 screw per lamp / unscrew them and slide remove its a 194 bulb so get some ready then replace and put back / Please rate my response thank you very much

Feb 01, 2009 | 2002 Toyota Avalon

Not finding what you are looking for?
2002 Hyundai XG350 Logo

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14850 Answers

Brad Brown

Level 3 Expert

18523 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...