Question about 2007 Dodge Grand Caravan SXT Minivan

ARE THE NUTS AND BOLTS ON MY 96 PLYMOUTH VOYAGER METRIC OR SAE, MAINLY THE ENDS OF MY STEEL BRAKE LINES

1 Answer

danny herget

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

President:

An expert whose answer got voted for 500 times.
Master
1,627 Answers

Most of the vehicle hardware is metric but brake lines could be either.If a 3/8 is too small and a 7/16 is too big then you need a 10mm.

Posted on Oct 26, 2009

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1 Answer

Changing rack n pinion on a 99 Plymouth voyager

take off both tie rod ends their are 2 nuts on the bottom their is two power steering lines on the passenger side when you have the lines off the rack will just pull off the steering rod when you put it back in you line up your steering wheel on the inside

May 02, 2015 | 1999 Plymouth Voyager

1 Answer

Bolt thread size for 1967 Jag hood 340 Mk II ?...looks like 1/4" x 3/4" very fine thread but Metric & SAE doesen't fit... nuts welded in hood...Dr. Muehlig

Metric Bolts-- the smaller ones-- come in 3 thread
pitches,so you need to find the correct one
Take out one on the other side as your sample

Aug 09, 2013 | Jaguar S-Type Cars & Trucks

1 Answer

Are the brake lines on a 1996 plymouth grand voyager metric or standard?

all brake lines are 3/16

Dec 05, 2012 | 1996 Plymouth Grand Voyager

1 Answer

Need a diagram for 2000 plymouth voyager brake lines

Diagrams are next to non existent

Have to duplicate what is there,always
been that way

Dec 02, 2012 | 2000 Plymouth Voyager

1 Answer

96 plymouth grand voyager is stuck on park what does that mean?

Your problem might be with the brake light switch. This switch is under the brake pedal, and when the pedal is pressed, it lets you shift your van out of park. This switch also activates the brake lights when you press the brake pedal. Try checking if your brake lights work. These switches are inexpensive, and very easy to replace.
Matt

Jun 15, 2011 | 1996 Plymouth Grand Voyager

1 Answer

I have a 91 toyota mr2 which need to change the clutch line from clutch master cylinder to slave cylinder. Where can i get the aftermarket parts? or i can just replace the rusty part, but where can i get...

I hate this particular project. Yes, you need metric ends at least. The problem of course is that auto parts stores don't carry long lines with metric ends. I ended up getting a "pipe flaring tool" so that I could put my own metric ends on the standard pipe. I then bought a short 7" metric line from a parts store, and cut it to use the ends on new standard size line. You will either want to get a nice one on loan from a friend or take the car to a shop. The cheap $30 tool I bought at one of the big auto parts stores didn't even work correctly out of the box. Ended up buying a $150-200 one that works great! Still a lot of work and expense if you are doing it yourself. The line is hard to get to once it gets up to the front of the car, so cutting out the bad rusty part and putting ends on is the easier do-it-yourself project - if you have the brake line flare tool. I would take it to a shop. Good luck!

Nov 11, 2010 | 1991 Toyota MR2

1 Answer

Where can I find the 2 steel brake lines that go from the master cylinder to the abs and the 2 that go from the abs to the front wheels?

typically you fabricate these lines, but remeber they must be double flared on both ends.

Aug 27, 2010 | 1998 Plymouth Voyager

1 Answer

Seal is leaking and I am not sure how to remove the power steering pump on my 96 plymouth grand voyager with the 3.3 engine

the pump has to come out from under the vehicle. there should be 3 15mm bolts holding it on to a bracket. u will need to remove the lines and will need a pully puller to remove the pully. it can be quite a messy job to do at home if thats your plan.

Jan 26, 2010 | 1996 Plymouth Voyager

2 Answers

How many bolts on my starter...94 plymouth voyager

2 nuts that hold the wires on. and two bolts that hold it on to the housing. Thanks for using fixya.

Sincerely

JC

Jan 08, 2009 | 1994 Plymouth Voyager

1 Answer

99 Plymouth Voyager Rear Bumper

If you look up from under you should see some push clips. if your removing entire bumper with rebar & all, it's probably about 4 nuts holding it to bumper shocks, but be sure to look near ends at fenders for push clips , and or screws, and across mid section. watch it, it's pretty heavy with the rebar attached so make sure you have everything ready & remove nuts last, with some help to hold it up.

Aug 05, 2008 | 1999 Plymouth Grand Voyager