Question about 2007 Chevrolet Aveo Sedan

1 Answer

Front wheel drive wheel bearing replacement - 2007 Chevrolet Aveo Sedan

Posted by dwhi840000 on

Ad

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 16 Answers

Pretty easy.....take off wheel and u will need a torque wrench just take off the 1 nut on your hub, you'll have to tak eoff your calipers as well.

Posted on Oct 27, 2009

Ad

5 Related Answers

Anonymous

  • 24 Answers

SOURCE: replace front wheel bearings

The bearings in your car are pressed into a hub. If the part is available as an assembly, it can be replaced that way. Generally on a front drive car:
Remove wheels and brake calipers
If it is pressed in: remove the rotors, disconnect the drive shafts and remove the steering knuckle. Then the old bearing is pressed out and the new one pressed in with a machine shop press. If the bearing is part of the hub, that will be unbolted and the new one swapped.

On a scale of 1-10 difficulty, Id rate it a strong 7

Posted on Jun 20, 2008

Ad

Anonymous

  • 19 Answers

SOURCE: Replacing front wheel bearing

The brake rotor needs to be removed, drive shaft nut in center of hub then 3 bolts hold the hub assembly to spindle from back side. if it has abs unplug it then some work will need to be done with a hammer and chisel to work the bearing out of spindle and axle shaft from bearing

Posted on Oct 16, 2008

blueextc3221

blueextc3221

  • 15935 Answers

SOURCE: replacing front wheel bearing

  1. Loosen the wheel nuts and the center axle nut.
  2. Raise the vehicle and safely support it.
  3. Remove the wheel. Remove the ABS speed sensor if so equipped.
  4. Unclamp the brake hose from the shock absorber, but do not disconnect the line.
  5. Remove the brake caliper and hang it out of the way on a piece of stiff wire. Do not disconnect the brake line; do not allow the caliper to hang by the hose.
  6. Remove the brake disc.
  7. Place a dial indicator near the center of the axle hub, and check the backlash in the bearing shaft direction. Maximum is 0.0020 inch (0.05mm). If the backlash exceeds the maximum, replace the bearing.
    1. Usiung a dial; indicator, check the deviation at the surface of the axle hub outside the hub bolt. Maximum is 0.0028 inch (0.07mm). If the deviation exceeds the maximum, replace the axle hub.
    2. Install the disc and caliper. Tighten to 65 ft. lbs. (88 Nm).
  8. Remove the cotter pin and install the wheel. Lower the vehicle to the ground.
  9. Remove the lock nut cap. While depressing the brake pedal, remove the center axle nut.
  10. Raise and support the vehicle again and remove the wheel, caliper and disc.
  11. Loosen the 2 nuts on the lower side of the shock absorber. Do not remove the 2 nuts and bolts.
  12. Remove the cotter pin and nut from the tie rod end.
  13. Remove the tie rod end from the knuckle using a joint separator or equivalent.
  14. Remove the bolt and 2 nuts holding the bottom of the ball joint to the control arm and separate the arm from the knuckle.
  15. Remove the 2 nuts from the steering knuckle. Place a protective cover or shield over the CV boot on the driveshaft.
  16. Using a plastic mallet, tap the driveshaft free of the hub assembly.
  17. Remove the bolts and remove the axle hub assembly.
    1. Clamp the knuckle in a vise with protected jaws.
    2. Remove the dust deflector. Loosen the nut holding the ball joint to the knuckle. Use a ball joint separator tool or equivalent to loosen and remove the joint
    3. Use a slide hammer/extractor to remove the outer oil seal.
    4. Remove the snapring.
    5. Using a hub puller and pilot tools or equivalents, pull the axle hub from the knuckle.
    6. Remove the brake splash shield (3 bolts).
    7. Use a split plate bearing remover, puller pilot and a shop press, remove the inner bearing race from the hub.
    8. Remove the inner oil seal with the same tools used to remove the outer seal.

    To install:
    1. Place the inner race in the bearing. Support the knuckle and use an axle hub remover with a plastic mallet to drive out the bearing.
    2. Clean and inspect all parts but do not wash or clean the wheel bearing; it cannot be repacked. If the bearing is damaged or noisy, it must be replaced.
    3. Press a new bearing race into the steering knuckle using a bearing driver of the correct size.
    4. Place a new bearing inner race on the hub bearing.
    5. Insert the side lip of a new oil seal into the seal installer and drive the oil seal into the steering knuckle.
    6. Apply multi-purpose grease to the oil seal lip.
    7. Apply sealer to the brake splash shield and install the shield.
    8. Use a hub installer to press the hub into the steering knuckle.
    9. Install a new snapring into the hub.
    10. Using a seal installer of the correct size, install a new outer oil seal into the steering knuckle.
    11. Apply multi-purpose grease to the seal surfaces which will contact the driveshaft.
    12. Support the knuckle and drive in a new dust deflector.
    13. Install the ball joint into the knuckle and tighten the nut to 105 ft. lbs. (142). Install NEW cotter pin.
    14. Temporarily install the hub assembly to the lower control arm and fit the driveaxle into the hub.
    15. Install the knuckle to strut bolts, then attach the tie rod end to the knuckle.
    16. Tighten the strut bracket nuts to 203 ft. lbs. (275 Nm) and tighten the tie rod end nut to 36 ft. lbs. (49 Nm). Install the NEW cotter pin.
    17. Connect the ball joint to the lower control arm and tighten the nuts to 105 ft. lbs. (142 Nm).
    18. Install the brake disc.
    19. Attach the brake caliper to the knuckle and tighten the bolts to 65 ft. lbs. (88 Nm).
    20. Install the center nut and washer on the drive axle.
    21. Install the ABS speed sensor if so equipped. Install the wheel
    22. Lower the car to the ground.
    23. Tighten the wheel nuts to 76 ft. lbs. (103 Nm). Tighten the hub nut while depressing the brake pedal to 137 ft. lbs. (186 Nm) on 1988-91 models and 152 ft. lbs. (206 Nm) on 1992-97 models. Install the cap and cotter pin.
    24. Remove the protective cover from the CV boot. Check front wheel alignment

Posted on Apr 25, 2009

Anonymous

  • 2 Answers

SOURCE: How to replace front wheel bearing on a 2002 Dodge 1500

You take off the right tire. You have take all the bolts out from underneath the

Posted on Feb 06, 2010

jimmy

  • 409 Answers

SOURCE: replacing front wheel bearings on a 2004 Suburban

The front wheel bearings are sealed units, and must be replaced with the entire hub assembly. They do not need periodic cleaning/replacing as they did in the old days, if they are not making noise do not bother with them.

Posted on Apr 07, 2010

Testimonial: "Thanks"

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is it possible to remove and replace front wheel bearings with out a press


In order to remove the front wheel bearings without press hub off the bearing and then the bearing out of the knuckle. To do the first step need a a Support Bridge.It is a special tool. Make bridge and use a general bearing pulled kit to replace bearings. use a "Front Wheel Drive Bearing Removal Adapters Puller Pulley Tool Set Kit" .To replace the bearing, remove front CV shaft taking care not to move the CV shaft too far out .

Nov 06, 2015 | 2002 Kia Rio

1 Answer

I have replaced wheel bearing hub and still got whining in front end


if while in motion other bearing or you replaced the wrong one or it's a drive belt pully bearing.

Dec 25, 2014 | Cars & Trucks

1 Answer

Replace wheel bearing


which wheel bearing front rear on the front with front wheel drive you will need to remove the steering knuckle and then press the bearing out with a shop press then press hub back in to bearing on the rear it is most likely a bolt in easy

May 28, 2013 | 1989 Cadillac Sedan DeVille

2 Answers

How do you check wheel bearings?


Most cars will go their liftime without a problem from wheel bearings. And they let you know when they go by billowing smoke out of the wheel as you drive, then it is too late, But the fronts are fairly easy, the rears, you cannot check, you have to go by ear, If they are grinding back there, they need attention, rear axle cars only, not front drive, the fronts are on a spindle that is easily accessed, Just rocking the wheel will tell you if it loose, but always listen first for for dry grinding sound, It will eventually get worse. Hope this helps.

Apr 16, 2012 | 1999 Dodge Grand Caravan

2 Answers

My right front wheel makes a rattlen sound while i drive, jacked it and when i shack my wheel it moves a little in and out. what could this be? Thanks!!!! 1989 cadillac deville


Please replace your wheel bearings before you drive it anymore. It could possibly cause the wheel to come off and go into your wheel well. Your wheel bearings are bad..Depending on how much you drove it after hearing it, you may need a new spindle also.

Feb 22, 2011 | Cadillac DeVille Cars & Trucks

1 Answer

2wd front wheel need to replace bearings or hub assembly which is best


A Front Wheel Drive Vehicle Can Have Two Types Of Rear Wheel Bearings: Serviceable Bearings, Or Nonserviceable, Sealed Bearings. When Sealed Bearings Fail, The Bolts Holding The Bearing And Hub To The Axel Or Control Arm Must Be Removed. When Installing The New Bearing Assembly, Torque The Bolts To Specifications.Some Manufacturers require The Use Of New Fasteners When Rear Bearings And Hubs Are Replaced.

When A Serviceable Wheel Bearing Is Used, The Bearing Can Be Disassembled And Packed With Grease.It Is Serviced Like A Front Wheel Bearing On A Rear-wheel-Drive-Car.

Apr 09, 2010 | 2003 Ford Explorer Sport Trac

1 Answer

Front wheel bearings on an Acura TL


ya no prb u can do that for the front wheels...but careful that u better check the bearings of rear wheels also...so that it will be safe drive for u!!!!

Jul 25, 2009 | 2000 Acura TL

3 Answers

Right front bearings need lube


Hi if you are refering to the hub bearing it can not be lubed it is a sealed bearing it will have to be replaced

May 04, 2009 | 2002 Buick Park Avenue

1 Answer

Chey aveo front hub bearing what is this?


yes front wheen drives have hub bearings. Most of them need the hubs to be pressed apart to replace them. the hub bearing supports the end of the CV drive shaft closest to the wheel. hope that helps.

Mar 17, 2009 | 2004 Chevrolet Aveo

1 Answer

Replace front wheel bearings


The bearings in your car are pressed into a hub. If the part is available as an assembly, it can be replaced that way. Generally on a front drive car:
Remove wheels and brake calipers
If it is pressed in: remove the rotors, disconnect the drive shafts and remove the steering knuckle. Then the old bearing is pressed out and the new one pressed in with a machine shop press. If the bearing is part of the hub, that will be unbolted and the new one swapped.

On a scale of 1-10 difficulty, Id rate it a strong 7

Jun 20, 2008 | 1998 Nissan Sentra

Not finding what you are looking for?
2007 Chevrolet Aveo Sedan Logo

942 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

john h

Level 3 Expert

23504 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...