Question about 2001 Hyundai XG300

2 Answers

How do i remove a belt from a 2001 hyundai xg300 car

Posted by isabel_melen on

Ad

2 Answers

Greg Bernett

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 2,989 Answers

Removal & Installation

  1. Raise and support the vehicle.
  2. Remove the engine splash shield.
  3. Rotate the drive belt tensioner clockwise to release the drive belt tension.
  4. Remove the drive belt from the alternator.
  5. Slowly release the drive belt tensioner.
  6. Remove the drive belt from the accessory drive pulleys.
To install:
  1. Install the drive belt to the accessory drive pulley.
  2. Rotate the drive belt tensioner clockwise.
  3. Install the drive belt to the alternator.
  4. Ensure the drive belt is properly aligned and seated into the grooves of the accessory drive pulleys.
  5. Slowly release the drive belt tensioner
  6. Install the engine splash shield.
  7. Lower the vehicle.

how do i remove a belt from a 2001 hyundai xg300 - 6a7dc59.gif
Accessory drive belt routing—1.5L engine

Acceshow do i remove a belt from a 2001 hyundai xg300 - 750e1de.gifbelt routing—2.0L engines


Accessory drive belt routing—2.4L engines

Accessory drive belt routing—2.5L and 2.7L engines

5315739.gif
Accessory drive belt routing—3.0L and 3.5L engine

Posted on Oct 17, 2009

Ad

Rich

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 114 Answers

Release the tension in the belt tensioner

Posted on Oct 17, 2009

Ad

5 Related Answers

Anonymous

SOURCE: hyundai 2001 XG300 tensioner pully adjustment

the belt that goes on the alt. ?? if so the tensioner is accessed from under neath the car. You will have to remove the right side tire and plastic sheild that is in place. When you look up at the bottom pulley you will see a nut head. If you lay on your back and look up at the engine, it will be located on the left or front side of the car.

Posted on Sep 06, 2008

ghost4548

Paul McGrath

  • 776 Answers

SOURCE: replacing 2001 Hyundai XG300 headlight, how difficult?

1bd6158.jpg Here's a photo - remove cap, disconnect connector to bulb, move bulb retainer out of the way & extract bulb - installation of new bulb is in reverse order.
If you want to replace the entire ASSEMBLY, there are three (3) 10mm bolts holding the assy. Remove them, then slide assy forward to access connectors - disconnect them.



06bdfd0.jpg

Posted on Jun 20, 2009

paul campbell

  • 1071 Answers

SOURCE: 2001 Hyundai XG300 with an engine light (p0715/P1159)

clean up all ground wires but you may need both of those items

Posted on Jul 21, 2009

johnjohn2

Johnny Brown

  • 5763 Answers

SOURCE: 2001 hyundai xg300. Driving on hiway, car makes a

Have someone rescan the computer wiyh a good scan tool, p1159 is not a good code for a 2001 xg300,

Posted on Sep 02, 2010

ZJLimited

ZJ Limited

  • 17970 Answers

SOURCE: how do i remove the

Sonata, Xg 300 And Xg 350

1. Before servicing the vehicle, refer to the Precautions section.
2. Disconnect the negative battery cable.

CAUTION
After disconnecting the negative battery cable, wait for at least 30 seconds for the SRS module to deplete its stored energy.
1. Drain the cooling system into a clean container for reuse.
2. Remove the heater hoses from the heater housing.
3. Discharge and recover the air conditioning system refrigerant.
4. Remove the suction and discharge hoses from the evaporator assembly. Cap the hoses to minimize contamination.
5. Remove the evaporator drain hose.
6. Remove the SRS module and the steering wheel by removing or disconnecting the following:
Steering wheel-to-SRS module nuts
SRS module from the steering wheel and disconnect the electrical connector


CAUTION
Store the SRS module in a safe place with the front facing upward.

Steering wheel-to-steering column nut
Steering wheel from the steering column

zjlimited_196.jpg

Fig. Instrument panel assembly-Sonata (clock over image for zoom)

zjlimited_197.jpg

Fig. Instrument panel screw locations-Sonata

1. Remove or disconnect the following:
Front and rear console assembly and remove both side covers
Glove box, the center pad cover, the center crash pad and the cassette assembly
Lower crash pad. Remove the console mounting bracket and the center support bracket
Rear heater ducts from the heater housing
Control assembly
Blower speed control actuator connector and the blend door actuator connector, if equipped with semi-automatic temperature control
4 retaining bolts and remove the heater assembly

2. Disassemble the heater housing by removing or disconnecting the following:
Vacuum motor-to-heater housing bolts (2 for each vacuum motor)
Vacuum motor rod end connection and remove the vacuum motors
Heater housing cover clips
Cover and the heater core


To install:

1. Install or connect the following:
Heater core and the cover
Heater housing cover clips
Vacuum motor rod end connection and install the vacuum motors
Vacuum motor-to-heater housing bolts (2 for each vacuum motor)
Heater assembly and attach it to the dash panel with the mounting bolts
Heater control assembly. Connect the ducts to the heater housing
Console mounting bracket and the center support bracket
Lower crash pad and both side covers
Front and rear console assembly


2. Install the SRS module and the steering wheel by installing or connecting the following:
Steering wheel to the steering column
Steering wheel-to-steering column nut and torque to 30-37 ft. lbs. (40-50 Nm)
SRS module to the steering wheel and connect the electrical connector
Steering wheel-to-SRS module nuts
Evaporator tubes, the heater hoses and the drain hose

3. Refill the cooling system.
4. Connect the negative battery cable.
5. Evacuate, charge and leak test the air conditioning system.
6. Operate the engine to normal operating temperatures; then, check the climate control operation and check for leaks.


Hope helps.

Posted on Dec 08, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 hyurdai xg300 how to replace crankshaft sensor


crank sensor is located on the front of the engine behind the
timing belt covers and is mounted to the front of the engine block. the alternator has to be moved to feed the harness down the front side of the block to replace the crank sensor it has a tone wheel that may have to be moved the remove and replace sensor

Mar 26, 2017 | 2001 Hyundai XG300

1 Answer

How to bypass the ac pulley on a 2001 hyundai xg300


You can possibly buy the belt for your model car that has no a/c. Just ask the clerk at the parts store for a belt for the vehicle that does not have a/c. If they do not sell one then you will have to take off the compressor and replace it with a pulley and braket.That is if they sell one for that particular vehicle.

Sep 08, 2016 | 2001 Hyundai XG300

1 Answer

Step by step instruction on replacing a timing belt in a 2001 xg300 hyundai


On the internet

Google the question

Go to You Tube Video & watch

Jul 15, 2014 | 2001 Hyundai XG300

1 Answer

2001 Hyundai XG300 with an engine light (p0715/P1159)


clean up all ground wires but you may need both of those items

Jul 21, 2009 | 2001 Hyundai XG300

1 Answer

Replacing 2001 Hyundai XG300 headlight, how difficult?


1bd6158.jpg Here's a photo - remove cap, disconnect connector to bulb, move bulb retainer out of the way & extract bulb - installation of new bulb is in reverse order.
If you want to replace the entire ASSEMBLY, there are three (3) 10mm bolts holding the assy. Remove them, then slide assy forward to access connectors - disconnect them.



06bdfd0.jpg

Jun 20, 2009 | 2001 Hyundai XG300

1 Answer

How change headlight on hyundai 2001 xg300


Remove the head lamp and disconnect the head lamp connector. 0f7fe9f.jpg Remove three 10mm bolts Unscrew the headlamp bulb CAPS to access bulbs. 5502d76.jpg

Jun 13, 2009 | 2001 Hyundai XG300

Not finding what you are looking for?
2001 Hyundai XG300 Logo

Related Topics:

3,203 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...