95 GRND CHEROKE sunroof supports have come loose and it leaks.

1. Place the ignition switch in the ON position.
2. Push and hold the sunroof switch toward 2 . Once the sunroof has reached the full tilt position, release the switch. Push and hold the switch toward the 2 position again. After a delay of four seconds, the sunroof will make a small movement and backup.
3. Release the switch.
4. Within 5 seconds of releasing the switch, push and continuously hold the switch toward 2 . The sunroof will move from the tilt position to the open position and back to the close position.

First off this is controlled by a module (computer) The switch would only have five volts . 5volt reference voltage from the control module . Not knowing how to test the electrical circuit's for this could be expensive . Short out the module or 5 volt ref. voltage circuit inside the module.
Your best bet , take it to a qualified repair shop . Look at a wiring diagram here http://www.bbbind.com/free_tsb.html Enter vehicle info. year , make , model and engine size . Under system click on body & accessories ,then under subsystem click sun roof . Then click search button then the blue link . Now tell me you under stand what's happening here .

Power Sunroof System Components
The power sunroof system consists of the following components:
• Sunroof control module
• Sunroof Opening Position Switch (SOPS)
• Sunroof switch
• Sunroof motor/actuator
• Sunroof glass (spoiler type, with glass sliding above roof)
• Sunshade
• Rail and track assembly upon which the sunroof glass rides
• Power supply for the sunroof control module: SUNROOF 20 A fuse
• Ground from G302

Sunroof Opening Position Switch (SOPS)
The SOPS tracks the position of the glass through 2 limit switches:
• Soft stop limit
• Vent limit
The sunroof control module monitors the limit switches and based on the inputs determines the position of the sunroof glass. As a limit switch closes, the 5 volt reference will be shorted to the sunroof limit switch low reference circuit, pulling down the 5 volt reference to 0 volts.
The sunroof control module understands the position of the sunroof glass based on the different input combinations through the sunroof limit switch soft stop signal and sunroof limit switch open vent signal circuits.

Power Sunroof Does Not Close
Perform the Initialization/Teach Process any time a new sunroof motor actuator is installed in the vehicle or any time an existing sunroof motor actuator is removed from the vehicle. Refer to Sunroof Motor/Actuator Initialization/Teach Process .

Check the RAP fuse in the rear fuse box , this fuse powers the sunroof control module ! Fuse Block - Rear , Left rear of the passenger compartment, under the rear seat .
The sunroof module contains the logic for the opening and the closing of the sunroof. The sunroof motor assembly contains the reversible DC drive motor, the gear train, and the limit switch.
The sunroof module determines the sunroof motor direction based on inputs received from the overhead console sunroof switches. When the ignition switch is in the ON position or when retained accessory power (RAP) is active, voltage is applied to the sunroof module via the RAP relay. For a description and operation of the RAP system, refer to Retained Accessory Power (RAP) Description and Operation in Retained Accessory Power. The sunroof module controls the sunroof motor direction by changing the polarity of the applied voltage. The sunroof module remembers the sunroof position whenever the ignition switch is turned to the OFF position. The limit switch is used as an input to the sunroof module to indicate that the glass is fully closed, or in the comfort stop positions. The limit switch is grounded when the sunroof glass is in the fully closed or comfort stop positions, otherwise it is open.
The SLIDE CLOSE mode is initiated by moving and holding the sunroof slide switch (ROOF) forward. This applies a ground provided from the sunroof limit switch low reference circuit to the sunroof switch close vent signal input of the sunroof module. The sunroof module controls voltage to the control circuits of the sunroof motor. The sunroof motor will run until the limit switch contacts are closed. The closing of the limit switch will apply the sunroof limit switch low reference circuit to the sunroof limit switch soft stop signal circuit to the sunroof module, indicating the flush closed position has been reached. As the sunroof is approaching the close position the sunroof glass will force the wind deflector downward.
You need to have a factory scan tool hooked up an have it checked for DTC'S in the sunroof control module ! a code reader will not do this , a code reader will only check the engine codes for OBD 2 .
Important: The following must be completed before using the symptom tables.

1. Perform Diagnostic System Check - Power Sunroof in order to verify that all of the following are true:
?€¢
No DTCs are set.



?€¢
The control modules can communicate via the serial data link.


2. Review the system operation in order to familiarize yourself with the system functions. Refer to Sunroof Description and Operation

your better off taking to the dealer !

god morning check the rails if there is any thing blocking the sunroof way, or the motor of the sunroof might be broken. but mostly the problem is from the rails.

have a nice day

These limits are not adjustable.

Do you know how to test automotive electrical circuit's with a DVOM - digital volt ohm meter ? When adjusting the moon roof did you see any switches ? sunroof limit switch
Measure the reference voltage of the sunroof limit switch soft stop signal circuit at the sunroof control harness connector to a good ground.
Does the reference voltage measure near the specified value?
4.5-5.5 V
Notice: Do not open the sunroof glass past the full open soft stop position. Doing so may damage the sunroof assembly and or the roof top.
Connect a jumper wire to the sunroof limit switch soft stop signal circuit at the sunroof control module harness to a good ground.
Turn ON the ignition, with the engine OFF.
Using the sunroof switch, operate the sunroof system, not to exceed the full open soft stop position.
Does the system operate as requested?

Do you know what a wiring diagram is ? Free one's here
http://www.bbbind.com/free_tsb.html Enter vehicle info. year ,make ,model an engine size . Under system click body & accessories ,then under subsystem click on sun roof . Click the search button then the blue link . See the control module , motor an the two switches ? One is probably miss adjusted . or bad !

Power Sunroof System Components
The power sunroof system consists of the following components:
• Sunroof control module
• Sunroof motor with the limit switches
• Sunroof switch
• Sunroof glass-spoiler type, with glass sliding above roof
• Sunshade
• Rail and track assembly upon which the sunroof glass rides
• Power sunroof system circuit breaker: PWR WDO 25 A
• Ground: G204

Sunroof Limit Switches
The sunroof limit switches track the position of the sunroof glass through two limit switches:
• Soft Stop limit switch through the sunroof limit switch soft stop signal circuit
• Vent Stop limit switch through the sunroof limit switch range signal circuit
The sunroof control module monitors the limit switches and based on the input combinations, determines the position of the sunroof glass. As a sunroof limit switch closes, the 5 volt reference will be shorted to the sunroof limit switch low reference circuit, pulling the 5 volt reference to 0 volts.
The sunroof control module monitors both sunroof switch input requests and based on the sunroof limit switch input combinations, will control an output to the sunroof motor, to drive the sunroof glass to the requested position.

Sunroof Motor
The sunroof has a bi-directional motor. When the motor is not operating both circuits are grounded. When the motor drives the sunroof glass in the direction from the closed to vent or vent to open position, the following occurs:
• Voltage is supplied to the sunroof motor open circuit.
• Ground is maintained to the sunroof motor close circuit.
When the motor drives the sunroof in the direction from the open to vent or vent to closed position, the following occurs:
• Voltage is supplied to the sunroof motor close circuit.
• Ground is maintained to the sunroof motor open circuit.
The sunroof control module is equipped with a timer circuit which stops the operation of the sunroof motor after 8 seconds.

the procedure for resetting the travel limits for the sunroofs of the lr3's is with the engine running, hold the sunroof switch to the open position until the sunroof automatically opens and closes and stops moving. this takes about a minute. i'm not positive that the procedure is the same on the freelanders, but it's worth a shot. if it doesnt work in the open position try it again in the closed position. good luck!

H Kim -

The "gearbox" is unfortunately under the headliner with no easy access. If you are also experiencing a clicking sound when the motor is activated, the regulator track had slipped position and will need to be reset.

I have been through this problem twice now. The first time the motor / gearbox came loose from it's mounts, began slipping (click, click,click), very nasty sound. I remounted the motor with threadlock on the screws, but alas.. two years later (mine's 2006) it slipped again.. I don't know why yet, I need to drop the headliner once more and have a look. If you would like a copy of your FSM, drop me a line.

Here's the RESET procedure from the FSM, absolutely gospel, no other way to fix it:
Sunroof Motor Assembly Note: Note • If the guide is removed, initial position setting of the sunroof motor will be required. After installing the sunroof unit, perform initial position setting using the following procedure. 1. Press the TILT UP switch to fully tilt up the glass panel.
2. When the glass panel reaches the fully tilt up position, temporarily release the TILT UP switch and press it again for approx. 13 s continuously. Continue pressing the switch until the glass panel automatically stops at the fully tilt up position after reaching the mechanical lock position.
3. When the glass panel stops at the fully tilt up position, temporarily release the TILT UP switch, then press it again within 5 s and hold.
Note • Press the TILT UP switch continuously until the glass panel opens to the fully open position, returns to the fully closed position and then stops. 4. Release the TILT UP switch when the glass panel stops at the fully closed position.



ALSO, Here's the clearance adjustment specs for having the glass panel in the correct resting position:


GLASS PANEL ADJUSTMENT
1. Fully close the glass panel.
2. Measure the gap and height difference between the glass panel and the body.
3. Loosen the glass panel installation screws and move the glass panel to adjust.


Standard clearance a: 0.2-2.2 mm {0.008-0.08 in} b: 0 mm {0 in} 4. Tighten the screws.
5. Insert any available thin plastic card between the weatherstrip and the body, and verify that they are sealed. (There is resistance when the plastic card is moved.)


• If they are not sealed, perform Steps 3-4 and adjust again.

Turn ignition on, make the sunroof go up and all the way down, turn off ignition and press the sunroof button to go down. Then unclip the 2 front hooks and push up.