Question about 2000 Hyundai Sonata

1 Answer

I have a 2000 hyundai Sonata, 6 cylinder eng. My

I have a 2000 hyundai Sonata, 6 cylinder eng. My car cuts out while driving, usually happens once I hit 3,000 rpms, and won't go above 70 mph. Pulled codes on check engine light and had two codes come up; oxygen sensor and crankshaft position sensor. I'm told to change the crank position sensor first. How do I change the sensor??

Posted by talisha3a on

Ad

1 Answer

PAUL MC G

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,280 Answers

The sensor is located on the left hand rear side of the block (near the bell housing). It is held in place by a 10mm bolt. It's to the right of the exhaust manifold (LH - radiator side) on the V6. Once you purchase the new sensor you'll be able to identify it on the engine. The connector to this sensor is located in the illustration.
I have a 2000 hyundai Sonata, 6 cylinder eng.  My - 2cb09a4.jpg A word to the wise... replace the O2 snsr as well.

Posted on Oct 04, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I35 rev limit at 2500


the Fuel Injection Pressure Damper can cose the same problim

Nov 27, 2012 | 2004 Infiniti I35

1 Answer

Automatic, V-6, ideal RPM at 70 MPH?


Sounds like the transmission is not shifting into a higher gear. 2,500 to 3,000 rpm would be more realistic for a highway cruising speed. The higher rpm may not be a big deal as far as the engine is concerned but it will hit you pocket book pretty good when you loose the mpg that you should get. I would personally either limit your driving until it can be checked or at least slow down so that the RPMs are in the range listed above. Let me know what they find, my curiosity is peaked!

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Feb 22, 2012 | 1989 Dodge Raider

1 Answer

WHERE IS THE SERPENTINE BELT LOCATED ON A 2003 HYUNDAI SONATA


Vehicles Covered: Hyundai Sonata 2002-2004 (2.4L & 2.7L Engines)

In 2003, Hyundai produced two types of Sonata:
Available engines:
4 Cylinders 2.4L VIN "S", MFI DOHC - see Figures 1 and 3.
6 Cylinders 2.7L VIN "H", MFI DOHC - see Figures 2 and 3.

To differentiate between these types of 2003 Hyundai Sonatas, the VIN 8th digit (Engine Type) will either be "S" or "H" as in the table above.

To locate the Engine drive belt, jack up the vehicle & place it onto jack stands, then slide under the car (toss a cardboard mat down first), then, once under the car, remove the (plastic) engine splash shield. Once removed, the drive & accessory belts are easily observed.

12_27_2011_5_25_29_am.jpg

Fig. 1 Accessory Drive Belt Routing 2.4L (4 cyl) Engine - Hyundai Sonata
The "COMPRESSOR" refers to the A/C compressor, and "GENERATOR" refers to the Alternator.


12_27_2011_5_27_01_am.jpg

Fig. 2 Accessory Drive Belt Routing 2.7L (6 cyl) Engine - Hyundai Sonata
The Belt Routing on the Left is "With A/C", on the Right is "without A/C"

Inspection - Drivebelt and Accessory Belts

Inspect the drive belt for signs of glazing or cracking. A glazed belt will be perfectly smooth from slippage, while a good belt will have a slight texture of fabric visible. Cracks will usually start at the inner edge of the belt and run outward. Worn or damaged drive belts should be replaced.

Drivebelt Removal & Installation - 2003 Sonata (2.4L and 2.7L engines)

Raise and support the vehicle.
Remove the engine splash shield.
Rotate the drive belt tensioner clockwise to release the drive belt tension.
Remove the drive belt from the alternator.
Slowly release the drive belt tensioner.
Remove the drive belt from the accessory drive pulleys.

To install:

Install the drive belt to the accessory drive pulley.
Rotate the drive belt tensioner clockwise.
Install the drive belt to the alternator.
Ensure the drive belt is properly aligned and seated into the grooves of the accessory drive pulleys.
Slowly release the drive belt tensioner
Install the engine splash shield.
Lower the vehicle.

Here's the best illustration I can find of the Hyundai 2.4L and 2.7L engines - the drivebelt seems to be located on the passenger side of both of these transversely mounted engines.

12_27_2011_6_03_16_am.gif

Fig. 3 Hyundai 2.4L and 2.7L engines - Underhood sensor locations 2002-2004 only

Glossary of Acronyms
---------------------------------
A/C - Air Conditioning
DOHC - Dual Overhead Cam
MFI - Multi-port Fuel Injection

Dec 25, 2011 | Hyundai Motor 2003 Sonata

2 Answers

Timing belt replacement interval


My rule of thumb for Timing belts:
replace at 60,000 miles, and every 40,000 miles thereafter. Having said that, I often let
cars go until the timing belt starts showing signs of wear (usually every 50K - 75K miles)

But www.autozone.com (register free at www.autozone.com) is recommending for your
car driving in "severe driving conditions" (aka normal stop-start driving) that your 2000 Sonata
have:
60,000 miles - replace
90,000 miles - inspect for wear
120,000 miles - replace
150,000 miles - inspect for wear

The 155 page owners manual (I found one at the link below - you may prefer to try Hyundai)
makes no mention of the timing belt at all.

http://www.scribd.com/doc/29113477/2000-Hyundai-Sonata-Owners-Manual

Jan 02, 2011 | 2000 Hyundai Sonata

2 Answers

Engine cut off while driving 2004 Hyundai Sonata.


BEST SOLUTION: Take/Tow your vehicle to an authorized Hyundai dealership and pay the diagnostic fee... they will tell you exactly what the problem is and the cost of parts/labor to fix it... at least this way you'll know what the problem is and what's required to fix it.

Aug 07, 2009 | 2001 Hyundai Sonata

1 Answer

2000 grand caravan won't go above 70 mph. high rpms


First I need to ask is it a 4 speed or a 3 speed transmission. If it's a 4 speed when driving down the road pull it from drive to third gear. You shpuld hear the engine speed up if it does not then that means you have on 4th gear and you will have to take it to a transmission shop. If it's a 3 speed then just count the shift points if all 3 gears are present then drive down the road and see if the van goes into tcc. When you mean the rpms are high how high are they.

Jul 15, 2009 | 2000 Dodge Caravan

2 Answers

Engine revs up to 3000-4000 rpm all by itself


THERE IS A TEMPERATURE SENSOR ON MOTOR WHICH CAUSES THIS PROBLEM... USUALLY IT SHOWS A NEGATIVE TEMP READING WHICH CONFUSES THE COMPUTER CAUSING IT TO REV UP....HAVE THE ENGINE DIAGNOSED ON A SCANNER....GOOD LUCK...

May 17, 2009 | 2001 Hyundai Sonata

1 Answer

2000 HYUNDAI SONATA RADIO DOES NOT WORK AFTER BATTERY JUMP?


Does the Check Engine light come ON when this happens? Whenever the "Check Engine" light comes on, there is always a DTC (Diagnostic Trouble Code) stored in the ECM (Engine Control Module). You'll need an OBDII (On-Board-Diagnostics) scanner to retrieve any codes recorded/set in ECM. Once you do this and let us know what, if any codes are set, then we can go from there.

Mar 27, 2009 | 2000 Hyundai Sonata

5 Answers

Hyundai sonata cutting out while driving


I had the same problem with my 2000 Sonata a couple of years ago. It was the crank sensor and once replaced, it solved the problem.

Sep 10, 2008 | 2000 Hyundai Sonata

Not finding what you are looking for?
2000 Hyundai Sonata Logo

1,985 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...