Pls where is Swirl Control Solenoid Valve located in Infiniti QX4

Here's a link to code P1130. P1130 Swirl Control Valve Control Solenoid Valve Here's a link to code P1105. https://www.autocodes.com/p1105_nissan.html

P1130 Swirl Control Valve Control Solenoid Valve.

According to Nissan, each cylinder has a valve in the intake manifold to control the air volume in the intake. The code is for one of the swirl control valve solenoids.
Code 443 is for the EVAP canister purge volume control solenoid which is a part the computer uses to vent the gas tank.
I would recommend a shop for both codes.

P0443 INFINITI - EVAP Canister Purge Volume Control Solenoid Valve

Possible causes- EVAP control system pressure sensor
- Damage harness or connectors to the Purge Control Valve
- The valve circuit is open or shorted
- EVAP canister purge volume control solenoid valve may be faulty (The valve is stuck open)
Tech notes It's a very common problem with Infiniti vehicles. If the harness is not damaged, it's very likely that the problem is the canister purge volume control solenoid valve.


Read more: http://engine-codes.com/p0443_infiniti.html#ixzz1yqKLq8YE

i think the code you are using is correct but the way you are using is wrong so i suggest you to visit the link give this link help a lot to me http://toolsnyou.com/

P1130 Swirl Control Valve Circuit Malfunction - With Automatic Transmission Possible Causes

• Check for air leaks in the Air Induction system (e.g., in the intake manifold)
• Check for leaks or looseness in hoses and tubes between the intake manifold, vacuum tank and swirl control valve actuator
• Check for leaks or looseness in the hoses between the air cleaner assembly and the swirl control valve vacuum check valve
• Crankshaft position sensor (REF) signal problem
• MAF sensor has failed (it may be dirty or contaminated)
• One-way check valve has failed
• Swirl control valve actuator has failed (it may be damaged or sticking)
• Swirl control valve control connector is damaged (check pins for damage)
• Swirl control valve circuit is open, shorted to ground or shorted to voltage
• Swirl control valve has failed
• PCM has failed
• Throttle position sensor has failed
• Vacuum tank has failed

P1440...EVAP Control System (Small Leak)
Check your fuel cap & reset code,

Good luck, hope this helps,,,

DTC P1130 - Swirl Control Valve Control Solenoid Valve

Otros detalles acerca de los codigos de falla los puede encontrar en este enlace: manual_detalle.php?manual_id=101

Buena suerte.

P1446 - EVAP Canister Vent Control Valve Close
EVAP canister vent control valve remains closed under specified driving conditions.

This solenoid valve responds to signals from the ECM. When the ECM sends an ON signal, the coil in the solenoid valve is energized. A plunger will then move to seal the canister vent. The ability to seal the vent is necessary for the on board diagnosis of other evaporative emission control system components.

This solenoid valve is used only for diagnosis, and usually remains opened. When the vent is closed, under normal purge conditions, the evaporative emission control system is depressurized and allows EVAP Control System (Small Leak) diagnosis.

The EVAP canister vent control valve is located on the EVAP canister and is used to seal the canister vent.

Symptoms:
- Engine Light ON (or Service Engine Soon Warning Light)

About the possible causes that your must solved:
- EVAP control system pressure sensor and the circuit
- Blocked rubber tube to EVAP canister vent control valve
- EVAP canister vent control valve
- Water separator
- EVAP canister is saturated with water


Hope this helps.

https://www.autocodes.com/p1130_nissan.html

Hope this helps

I have been working on a 96 nissan truck for three years for an evap code and swirl control , I finally just made sure the swirl control solenoid operated properly then disconnected the vacuum hose from the swirl control actuator and plugged it . code fixed.been driving 3 months, no code