1999 bolt torque front& rear springs lantra

Hey Phil, sounds like you do quite a bit of work on your Tahoe.. you need one of these..

http://repair.chiltondiy.com/Pub/DIY/Product.aspx?ca=Repair&b=28779

Chevrolet Silverado Suburban Tahoe Avalanche GMC Yukon Yukon XL Yukon...

Chevrolet Silverado GMC Sierra 1999 thru 2006 2WD and 4WD

rear hub.
the lug bolts? name part exactly.

its in the FSM, go to Suzuki and get the factory service manual.
its all there.
or tell exact part, and what point of dissembly you are at
or what JOB attempting, that be a BIG clue. that.

Dana 50 Front Axle

Observe the following torques;

* Left and Right drive axles-to-cross member: 120-150 ft. lbs. (163-203 Nm)

* Axle arm-to-radius arm: 180-240 ft. lbs. (244-325 Nm)

* Coil spring insulator: 30-70 ft. lbs. (41-95 Nm)

* Upper spring retainer: 13-18 ft. lbs. (18-24 Nm)

-----------------------------------------------

Dana 60 Front Axle

Observe the following torques;

* Drive shaft-to-flange: 15-20 ft. lbs. (20-27 Nm)

* Track bar nut and bolt: 160-200 ft. lbs. (217-271 Nm)

* Stabilizer link nut: 20-30 ft. lbs. (27-41 Nm)

* Stabilizer barU-bolt: 50-65 ft. lbs. (68-88 Nm)

* Spindle connecting rod-to-knuckle: 70-100 ft. lbs. (95-136 Nm)

* Front spring U-bolt: 95-100 ft. lbs. (115-135)

Brake Pads Removal & Installation Front

To Remove:

1. Drain brake fluid to ½ full level in reservoir.
2. Remove the front wheels.
   
   
3. Remove the front brake caliper assembly.
4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
5. Remove the wear indicator from each of the 2 brake pads.

To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.

1. Using a large C clamp or equivalent press piston into the caliper.
2. Apply disc brake grease to the inside of each anti-squeal shim.
3. Install the anti-squeal shims on each pad.
4. Install the pad wear indicator clip to the pads.
5. Install the pads with the pad wear indicator plate facing upward.
6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
7. Install the front wheels.
8. Fill the master cylinder with new clean brake fluid.
9. Pump the brake pedal several times to seat the brake pads.

Rear TMC made rear brake components

TMMK made rear brake components

To Remove:

1. Drain the brake fluid to ½ full level in reservoir.
2. Remove the rear wheels.
3. Remove the caliper slide pins.
4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
5. Remove the rear brake calipers.
6. Remove the 2 brake pads with the anti-squeal shims.
7. Remove the anti-squeal shims and pad wear indicators from brake pads.

To Install:

1. Using a large C clamp or equivalent press the piston into the caliper.
2. Coat both sides of the outer anti-squeal shim with pad grease.
3. Install anti-squeal shims to each pad.
4. Install wear indicators on the 2 brake pads.
5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
   • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
   • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
7. Fill the master cylinder with new clean brake fluid.
8. Pump the brake pedal several times to seat the brake pads.
9. Install the rear wheels.

Brake Rotor Removal & Installation Front To Remove:

1. Remove the front wheels.
2. Remove the front brake caliper assembly.
3. Remove the front brake pads.
4. Remove the 2 bolts and caliper mounting bracket.
5. Place match marks on the disc and axle hub.
6. Remove the front wheel disc.

To Install:

1. Align the match marks and install the front disc.
2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
5. Fill the reservoir with brake fluid.
6. Bleed the brake system.
7. Install the front wheel.

Rear To Remove:

1. Remove the rear wheels.
2. Remove the brake caliper assembly.
3. Remove the brake pads.
4. Remove the 2 bolts and the caliper mounting bracket.
5. Place match marks on the disc and axle hub.
6. Remove the rear disc.

To Install:

1. Align the match marks and install the rear disc.
2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
   • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
   • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
   • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
   • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
5. Fill the reservoir with brake fluid.
6. Bleed the brake system.
7. Install the rear wheel

Removal & Installation To Remove:

1. Before servicing the vehicle refer to the precautions at the beginning of this section
2. Loosen the lug nuts on the wheel and tire assemblies but do not remove the lug nuts
3. Raise and support the vehicle
4. Remove or disconnect the following:
   • Wheel and tire assemblies
   • Axle lubricant into a suitable container
   • Rear driveshaft
   • Parking brake cable
   • Brake calipers
   • Shock absorbers from the axle brackets
   • Vent hose from the rear axle vent fitting
   • Nuts and the washers from the U-bolts
   • U-bolts, spring plates and spacers from the axle assembly
5. Lower the axle assembly from the vehicle

To Install:

1. Place the rear axle assembly under the vehicle
2. Align the rear axle assembly with the springs then connect the spacers, spring plates and the U-bolts to the rear axle
3. Raise the rear axle assembly into position
4. Install or connect the following:
   • Washers and nuts to the U-bolts; Torque to: 59 lb-ft. (80 Nm) then, Torque to: 89 lb-ft. (120 Nm)
   • Vent hose to the rear axle vent fitting
   • Shock absorbers to the rear axle
   • Brake calipers (See: Brake Caliper)
   • Parking brake cable (See: Parking Brake Cable)
   • Rear driveshaft (See: Rear Driveshaft)
   Wheel lug nut tightening sequence
   
   
5. Fill the rear axle with lubricant
6. Bleed the brake system (See: Brake Bleeding)
7. Install the wheel and tire assemblies
8. Lower the vehicle to the ground
9. Torque lug nuts as follows:
   • Single Wheel: Torque to: 140 lb-ft. (190 Nm)
   • Dual Wheel: Torque to: 175 lb-ft. (240 Nm)
10. Road test the vehicle to check performance

You're going to want to take that nerf bar, attach it to the spring leaf with the front bolt and frame as you say. Put some inhibitor behind the unit too. After flexing the torque rod for a while, move the rear axle upward by jacking underneath it. From there you should find that the whole thing just slips into place.

PLEASE DON'T FORGET TO RATE!!!

Removal & Installation

Remove or disconnect the following:

• Brake hose bracket screw from the control arm
  
• Shock absorber lower bolt while using a utility stand to support the rear axle
  
• Tie rod from the rear axle
  
• Spring and insulators after lowering the rear axle
  

Exploded view of the coil spring assembly


To install:

1. Install or connect the following:
   
   • Insulators and springs on the rear axle with the paint stripe is facing rearward
     
   • Rear axle tie rod after raising the rear axle into its proper position. Torque the nut to 92 ft. lbs. (125 Nm).
     
   • Shock absorbers to the rear axle. Torque the upper and lower nuts to 63 ft. lbs. (85 Nm).
     
   • Brake hose bracket to the control arm. Torque the bolt to 33 ft. lbs. (44 Nm).
     
2. Remove the axle supports.
   

Block the front tires. Break the rear lugs loose. Jack up the rear of the truck at the center if possible. remove the wheels & brake drums. Remove the brake shoes,return springs & all the other hardware. Remove the differential cover & drain oil. If you have a posi the next step sucks. You need to remove the threaded pin from the housing & remove the axle retaining clips. All the while,being carefull of the spring in the posi unit. If no posi,then same procedure,minus the "pucker factor". After the axle is out,take a large flat blade screw driver or pry bar & pop the seal out. Keep in mind the axle bearing is probably gone too , so that's another procedure. Keep it apart,you'll be glad you did.

They use throw away bolts. One use only, so don't reuse your old ones. You will need new ones. The smaller bolts 1st torque setting 22Ft/Lbs and the larger 26ft/lbs, the 2nd torque setting 60 degrees both bolt sizes and the 60 degrees for the third.

weird ??what are you carrying ??