Video on how to take the rear left side panel off of door 2010 GMC terrain

either debris or latch / linkage damage /disconnect crawl into back with a flashlight and long screwdriver remove the plug in rear panel and use screwdriver to move latch release

There are no grease fittings on the 2010 GMC Terrain.
The only items you can apply a thin film of white spray lithium grease are the door, hood and rear hatch hinges.

What would have blown the fuse? A defective component? So fuse or not there is an issue in the system and a new fuse will just blow again. Check the owner's annual for fuse locations, if there is a separate fuse hen it will be listed there.

Search Results

How To Install Replace Inside Door Handle Chevy Equinox ...

? 9:02
https://www.youtube.com/watch?v=cY6asyM2R6g
Feb 2, 2012 - Uploaded by 1A Auto Parts
How To Install Replace Inside Door Handle Chevy Equinox 05-09 1AAuto.com .... found your tutorial on fixing my driver's side door handle for my 2006 Equinox. .... Door Handles Chevy Equinox 2010 2011 2012 GMC Terrain ...

How To Install Replace Inside Door Handle 2007-13 ...

? 9:05
https://www.youtube.com/watch?v=QonKLwhk2CE
Apr 2, 2015 - Uploaded by 1A Auto Parts
http://www.1aauto.com/interior-door-handle-driver-side-front/i/1adhi00417 1A Auto shows you how to repair, install, fix,change or replace a broken or snappe... ... 10, 11, 12, 13 Chevy Silverado, Tahoe, Suburban and GMC Sierra, Yukon Denali ...2007-2011 Tahoe Yukon Suburban Escalade Vent Section ...Missing: terrain

How To Install Remove Rear Outside Door Handle 2007-13 ...

? 10:02
https://www.youtube.com/watch?v=7ZUTqqEzpZg

1) Front End Sensor - Right--Located under the front hood in the engine compartment (2) I/P Air Bag--Located at the top right under the instrument panel (3) Roof Rail Air Bag - Right--Located under the headliner, extending from the passenger front windshield pillar to the passenger rear windshield pillar (4) Side Impact Sensor (SIS) - RF--Located under the right front door trim near the lower rear of the door frame (5) Sensing and Diagnostic Module (SDM)--Located underneath the vehicle carpet under the center console (6) Seat Belt Pretensioner - RF--Located under the trim near the bottom of the center pillar (7) Side Impact Sensor (SIS) - RR--Located under the right rear door trim near the lower rear of the door frame (8) Roof Rail Module - Right--Located behind the garnish molding on the upper rear pillar (9) Roof Rail Module - Left--Located behind garnish molding on the upper rear pillar (10) Side Impact Sensor (SIS) - LR--Located under the left rear door trim near the lower rear of the door frame (11) Seat Belt Pretensioner - LF--Located under the trim near the bottom of the center pillar (12) Side Impact Sensor (SIS) - LF--Located under the left front door trim near the lower rear of the door frame (13) Roof Rail Air Bag - Left--Located under the headliner, extending from the driver front windshield pillar to the driver rear windshield pillar (14) Steering Wheel Air Bag--Located on the steering wheel (15) Vehicle Battery--Located at the front left of the engine compartment. (16) Front End Sensor - Left--Located under the front hood in the engine compartment

Check the video on the below link:
https://www.youtube.com/watch?v=C4ZrksFQwag
GMC Terrain Camshaft Position Sensor
http://workshop-manuals.com/gmc/terrain_fwd/l4-2.4l/transmission_and_drivetrain/transmission_control_systems/sensors_and_switches_transmission_and_drivetrain/sensors_and_switches_a/t/transmission_speed_sensor_a/t/component_information/locations/page_7020
GMC Workshop Manuals

Don't really know. But it is labeled ETAC in the fuse panel under the hood.

Lift up on the wiper assembly and slide the wiper blade off.
You will find there is no aftermarket blade refill that fits the 2010 Terrain. You will have to settle for a 12" refill.

It has a fuse, but may not be listed on the fuse panel. Your owners manual should have a complete list of every component on each fuse circut.

Wiper blade or arm? If you just need to replace the wiper blade it should just unclip from the arm. There is a small clip inside the blade if you look inside the arm as it loops around. Pry it inward to get it to snap out. Then just reinsert it the same way to reinstall