Question about 2006 GMC Canyon

1 Answer

2006 gmc canyon rear brake line plug from master cylinder size thread ?

Posted by todd chapman on

  • todd chapman
    todd chapman Apr 20, 2021

    no i need to plug the master cylinder temporarly and need to know the thread size that srews into the master cylinder back brake line so it can be protected and plugged

×

Ad

1 Answer

ADMIN Canada

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • GMC Master
  • 37,932 Answers

You mean the brake line flare nuts on the end of the lines? I see nothing that looks like a 'plug'. You buy the lines ready made or you have them made a garage, using a brake line flare tool set. eBay sells them ready made.

https://www.google.com/search?q=2006+gmc+canyon+rear+brake+line+plug+from+master+cylinder

..

Posted on Apr 20, 2021

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front brakes on 2005 GMC canyon are locked up what could it be


hello,
If the frt brakes are locked up then it could be any of the following, master cylinder is bad, frt brake lines are at fault the flexible rubber part that goes to the calipers, or the calipers themselves could be frozen and are not able to release when you let off the brake pedal.

Mar 14, 2015 | 2005 GMC Canyon

1 Answer

How do I release a stuck on emergency park brake?


hello,
if your e-brake is stuck then you could look at the unit on the side and there should be a small lever that you can pull to release the brakes if the cable is not working, the cables themselves could be frozen? or something mechanical inside the drums or calipers in the rear that could be stuck and not moving. there is a possibility that the master cylinder is at fault, but rare. you can open the rear wheel bleed valves and see if the vehicle can move? if so, then check the rubber lines to the wheels? to be bad

Jul 25, 2014 | 2005 GMC Canyon Extended

1 Answer

How to remove the front rotor 2004 canyon


Park the Canyon on a flat stretch of road or driveway and open the hood.

  • 2 Remove the master cylinder cap located near the firewall on the right side of the GMC's engine. Remove half of the brake fluid in the reservoir with a turkey baster. Lay the cap over the container.

  • Read more: How to Change Rotors on a 2005 GMC Canyon ' eHow.com http://www.ehow.com/how_6717490_change-rotors-gmc-canyan.html#ixzz29JfCwiDq

    Oct 12, 2012 | 2004 GMC Canyon

    1 Answer

    Replaced all brake lines, rear wheel cylinders, front calipers. No fluid to rear brakes, no fluid to master cylinder bleeder. Fluid is in front brakes. How to resolve? Thank you


    It sounds as though where the rear brake lines meet up with the master cylinder; there is probably a piece of dirt in the lines that could be blocking any fluid from getting in. To test this, I would remove the brake lines from the master cylinder and then remove the master cylinder. Once done, have the master cylinder cleaned inside out. This will remove the dirt particles that are clogging your lines.

    Aug 22, 2011 | 1988 GMC C2500

    1 Answer

    Soft brake pedal on 1990 GMC Sierra. Replaced master cylinder, rear shoes are almost new, front pads are good.


    if master replaced sounds like air still in lines rebleed the brake lines start with passenger rear than driver rear -pass front -than driver front last..before bleeding check rear brake shoes are adjusted correctly

    Aug 10, 2011 | 1990 GMC Sierra

    1 Answer

    2006 chevrolet 1500 brakes shimmy without touching them,also when setting still mash couple times let off ,wheels hard to turn


    check for front brake calipers dragging, if the are replace calipers and front brake hoses, if calipers ok replace master cylinder, This is how to check calipers, jack up front of truck have some one apply brakes and release as soon as they release the brake peddle the wheels should spin freely if not brake the brake line lose at master cylinder if wheels spin free with line loose replace master cylinder, if not replace calipers and hoses.....HOPE THIS HELPS

    Nov 16, 2010 | 2006 GMC Sierra 1500 2WD

    2 Answers

    Rear metal brake lines


    To get the length, just get a roll of string, run it along the existing brake line 'til u get to the rubber line. you can cut off the line near the master cylinder, bring it to the parts store, they can tell you what size you need. You will have to use several lengths of line to reach the back. If this line has rotted thru, you should change all the others, as they are likely to fail soon. countrycurt0

    Aug 20, 2008 | 1998 Jeep Cherokee

    Not finding what you are looking for?
    2006 GMC Canyon Logo

    Related Topics:

    42 views

    Ask a Question

    Usually answered in minutes!

    Top GMC Experts

    Ryan Lutton
    Ryan Lutton

    Level 3 Expert

    1266 Answers

    john h

    Level 3 Expert

    23884 Answers

    Mike

    Level 3 Expert

    4376 Answers

    Are you a GMC Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...