Question about Toyota Highlander

1 Answer

Where is the highlander fan blower motor resistor

Posted by Greg Rodden on

  • Brad Brown Mar 13, 2021

    Hi Greg Rodden, I want to help you with your question, but I need more information from you. Can you please add details in the comment box? what year

  • Patrick Whittingham
    Patrick Whittingham Jan 15, 2022

    2011 Toyota Highlander

×

Ad

1 Answer

ENFORCER

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

  • Toyota Master
  • 38,673 Answers

Under the dash where the fan is

Posted on Mar 13, 2021

Ad

5 Related Answers

Anonymous

  • 107 Answers

SOURCE: Lincoln 2000 town car Blower doesn't work at HI-MED-LOW speeds...

it is called blower motor resistor , should be close to blower motor , you will see a plug type connector with two screws , remove the screws and there should be a resistor inside the cover for the motor, swap with new and reassemble

Posted on Feb 19, 2009

Ad

Anonymous

  • 2 Answers

SOURCE: how to replace a blower motor resistor in a 2004 jeep liberty

You have to take the glove box off and it is right behind it, need a #20 Torx to take it replace it. The glove box is the hardest part of the job, I just replaced mine on an 05 Grand Cherokee but it didn't fix it for me, was well worth the $8.60 to try though.

Posted on Apr 06, 2009

Anonymous

  • 2 Answers

SOURCE: where is the blower motor resistor on a 2002 mazda protege?

just remove the glove box and its right behind it just take the white pug out and the two phillips screws to remove the resistor out, replace with the new one and cool off!!!! Hope this helps

Posted on Aug 04, 2009

Anonymous

  • 5 Answers

SOURCE: How do you replace blower motor resistor on a 2004

Here is how to change the resistor- but also pay attention-
Did you also change the connector at the same time?
If you are changing the resistor due to overheating and melting of plastic, then you need to do the connector also, or else it will repeat fail in a very short time.

Here is a step-by-step check you can do to fix it. If you are onlygetting high speed (setting 5), then most likely you have a resistorproblem, or the wiring connector to the resistor is bad. The groundwire prong being bad is a possible cause.

Check this for step-by-step checks:

http://www.sparkys-answers.com/2008/07/2005-chevrolet-silverado-blower-inop.html

Posted on Sep 19, 2009

Anonymous

  • 3 Answers

SOURCE: A/C Heater blower fan does not cycle through all speeds

Yes it is the blower Motors Resistor board. It is up behind the blower motor, just under the glove box. You have to remove the black KICK panel with its two "Push Pins" that will break too. There are 3 screws holding that resistor board in, the back two are a bear to get to. Good luck.

Posted on Feb 26, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Where is the blower motor resistor located at in a 2014 Toyota Highlander?

Typically it is directly in under the blower cover attached right in front of the fan. Take care in replacement to avoid bending the element in any way.
2helpful
2answers

2004 crown vic. only 63K miles on her. AC/heat fan was sporadically working, now its done. AC was nice and cold, working fine. Is the fan a hard replacement if I were to find one at a parts yard?

Try to check the power and ground on the blower fan. If you missing the ground on the blower fan connector than most likely it is the blower fan resistor (controller), it is located under the hood close to back firewall behind left cylinder head.
1helpful
1answer

The fan on my 2005 Highlander simply quit working. Could it be the fuse?

Could be fuse,fan itself and a switch called blower motor resistor these go a lot.good luck test fan motor on battery
0helpful
1answer

Blower motor

I'm showing a blower relay and a resistor used on models with manual ac control.
The blower motor is grounded and the fan switch provides power thru the resistor. So you have a 40amp blower fuse that handles high thru the relay, then a 30amp HVAC fuse that powers the blower thru the fan switch.
Do you not have power from the resistor to the blower motor on the purple wire ?
1helpful
1answer

My 2003 Toyota highlander blower turns on normally but after driving for more than 20 minutes, the blower seems to get weak. I have no freon issues, the blower just shuts down. If i turn the engine off a...

I would check the blower motor resistor pigtail for melted insulation.You may need replace the pigtail going to the resistor or replace the resistor itself,they get pretty hot and could loose its connection.
5helpful
2answers

01 grand.prix ac fan switch only works on high. has a duel temp controller when you turn fan off the only way fan comes back on is to move the temp controller levers

Hi!!
When the Blower Motor Resistor (controls blower speeds) goes bad, the blower motor works only on HIGH SPEED. REPLACE IT.
BLOWER MOTOR RESISTOR Removal & Installation
  • Disconnect negative battery cable.
  • Remove right lower instrument panel insulator panel.
  • Disconnect blower resistor connector located behind right side of dash.
  • Remove blower resistor screws and blower resistor.
To install, reverse removal procedure
Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa!!
5helpful
2answers

BLOWER HEATER FAN SWITCH IS ONLY WORKING ON HIGH SPEED WITH LITTLE HEAT.

The blower motor fan is controlled by the blower motor resistor.Its the resistor which controls the fan on respective speed which you select.But if the resistor goes faulty,then it will not be able to set the required speed which you set for fan,so it works on high speed only. In this case you will have to replace the blower motor resistor. Check fog for the location of blower motor resistor location:--- see part number 8 in the diagram below. helpmech_11.gif

The blower motor resistor is located next to blower motor under the dash.Its fitted with 2 screws and a wiring connector.You have to remove the screws and wiring connector and take the resistor out and place the new resistor in same position and connect the connector as well as screws. ------------------- this should help.Thanks.Helpmech.
0helpful
1answer

Where is the fuse to the heater fan blower located in my 2005 Pontiac Grand Prix. Owners manual has 3 different fans. Is it the HVAC fuse or one of the 3 fans? The heater fan quit and want to check the...

Hi, should be listed as heater blower motor not fans ,the fans is the ones in front of radiator. most common problems are the blower motor resistor, which is in passenger side compartment near fire wall.This is were your blower motor is also. You can check and see if its getting power to resistor, with a test light if power is at resistor, check and see if you are getting power at blower motor if no power there replace resistor. But if you have power at motor replace blower motor. If i can help further just re post. thanks
3helpful
2answers

2005 Chevrolet Silverado - Fan not coming on. When I turn the heater/ac blower fan on, fan does not work. Prior to completely going out, fan would quit working intermittently. Is this a fuse problem? ...

Chk for power at the blower motor electrical connector. If no voltage, check the blower motor resistor, its within the blower motor vent (this controls power to the blower motor). Also, in theses vehicles water may have damaged the blower motor itself. Inspect the blower motor for proper function.
0helpful
1answer

Need to replace ac/heater fan resistor I am not sure of the location does anyone know? Thank You

The Blower Motor Resistor is located on the passenger side firewall, not far from your A/C's H-Valve (or expansion valve), going inside of the vehicle. The blower motor resistor has a 4 or 5 way black connector plugged into it and this is the only visible portion of the Resistor you will see. Remove the wiring connector and remove the 2 or 3 screws with an 8 mm or 5/16" socket (8 mm and 5/16" are the same). Once the screws or fasteners are removed, just pull the blower motor resistor out of the firewall and if you look at it, it will have various coils of wire on it, sometimes it will show burnt coils, but you can always check the various coils with an Ohm-meter.

Aside from that, install the new Blower Motor Resistor and Voilà! Your inside Blower Motor should work just fine.

A brief note here, if your fan doesn't work when the fan switch is on High, then it's not the Blower Motor Resistor, but possibly the Blower Motor itself. Should this occur, please get back to me insofar as how to replace the blower motor and why the blower motor's wires have to be twisted...even with the new blower motor fan.

Best of Luck,

"00 Buck"

"Still living on the Right Side of Dirt..."
Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

393 views

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8991 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6963 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15008 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...