Question about 1999 Chevrolet K1500

2 Answers

Have a 1999 k1500 Chevy have no turn signal but do have flashers. This early 99 model left over 98 lol have replaced flasher and directional switch all fuses test good can find turn relay under dash only relay I found is mounted to top of heater box please help

Posted by Shawn ward on

Ad

2 Answers

Carl Rock

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 2,981 Answers

Pickup - Check the stop lamp relay and fuse 2 in underhood fuse block.

Diagram shows no stop lamp relay not used in suburban/utility.

Posted on Jan 27, 2021

Ad

Dan Hooper

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 3,622 Answers

If I am not mistaken, these have 2 separate flashers. One for the turn signals and one for the hazards. If memory serves correctly, the turn signal flasher is square and the emergency flasher is round.

Posted on Jan 27, 2021

Ad

5 Related Answers

Anonymous

  • 113 Answers

SOURCE: no flashers or turn signals

see if power is going through the switch

Posted on Jun 19, 2008

Anonymous

  • 1 Answer

SOURCE: no flashers or turn signals

Try the fuse/breaker panel under hood, drivers side.

Posted on Jun 26, 2008

Juan Guillen

  • 373 Answers

SOURCE: turn signals wont work but flashers do

Hi.
On your 98 Dakota.
Is equipaded with a single Flasher.
If you replace all ready.
Check the FUSE # 10, 15 amp..
On the Fuse box. left side of Dash.
and the FUSE D 25, amp. On engine compartment Fuse box.
Check the proper funtion of the HAZARD switch.
Bacause if the Hazard switch is bad the turn signal don't will work. Match the OLD flasher with the New one.

If after of this still not work.
Remove the steering wheel cover, locate the Turn signal switch connector and with a TEST Light check power with the Key ON
12v. to the RED wire and PINK wire..
If you found 12v. check the connection with the switch.
If the connection is good. you will need to replace the turn signal switch.
But if you don't found 12v. You need to look a an open circuit.
And fix it..

I hope this help on your problem..
Thank you for use fixya...

Posted on Sep 01, 2008

Ron szarafinski

  • 217 Answers

SOURCE: Turn signal does not flash right or left. Where is flasher unit?

yes it is the same. the problem is most likely the turn signal switch which is located on the steering column. be sure to check all fuses, relays, and bulbs first. keep me posted thanks

Posted on Jan 31, 2009

Anonymous

  • 112 Answers

SOURCE: 1990 Volvo 240 DL brake lights not working, fuse good, bulbs good

It's silver aluminum---not orange---that's fuel pump!

Posted on Mar 26, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

The turn signals don't work on a 99 Oldsmobile cutlass and the fuse isn't blown how can I fix


When the ignition switch is in the RUN or the START position, voltage is applied through the TURN/LPS fuse to the normally closed contacts of the hazard switch. A single flasher in the hazard switch performs the following functions:
• The turn signal operation
• The hazard flasher operation
When the turn signal switch is in the LEFT position, voltage is applied to the following components:
• The left turn indicator
• The left front park/turn lamp
• The left rear turn lamp
The lamps immediately turn on and flash as the flasher opens and closes the circuit. If a bulb is in need of replacement, the turn lamps will flash at twice the normal rate.
Without testing i would probably say the flasher is bad .
do the four ways work ?

Mar 02, 2018 | Oldsmobile Cars & Trucks

2 Answers

I have a1997 Chevy 1500 and I am wondering were is the flasher relay at.


Most cars the flasher relays are up under the dash not far from the steering column. I had several makes of cars and they all were up there.

Jan 10, 2016 | Cars & Trucks

2 Answers

How to change the signal flasher


Models from 98 on use a combination flasher. This flasher is mounted either on the front or on the back of the junction block.
The combination flasher is a smart relay that functions as both the turn signal system and the hazard warning system flasher. It is designed to handle factory-fitted equipment. If aftermarket equipment is added to this circuit (such as trailers with lights), the flasher will automatically try to compensate to keep the flashing rate the same.
  1. The flasher contains sophisticated internal circuitry that cannot be tested with conventional equipment. Substituting a new unit for a suspected defective version is the easiest test.
  2. On air bag-e quipped vehicles, disconnect the battery negative cable(s) and wait two minutes from the air bag capacitor to discharge.
  3. Remove the junction block cover. If the flasher is accessible, grasp and pull the flasher from the fuse panel.
  4. If the flasher is not mounted on the outside of the junction block, remove the steering column cover from the instrument panel. Reach through the opening to access the fuse block on the back of junction block. Pull off the flasher.
  5. Inspect the socket for corrosion or any other signs of a bad contact.
To install:
  1. Install a new flasher in the connector.
  2. Install the fuse panel cover.

zjlimited_225.jpg

Fig. Removing the steering column cover for access to the flasher


zjlimited_226.jpg

Fig. Early style flasher system: dual flashers mounted on junction (fuse) block. The turn signal flasher is the lower of the two; hazard flasher is the higher one

zjlimited_227.jpg

Fig. Combination flasher location (1) on fuse block (2) (later models)


Hope helps (remember to rate and comment this answer).

Dec 14, 2010 | 1999 Dodge Durango

1 Answer

Where is the signal flasher located on a 98 chevy cav.


Try below the steering column under the dash area.
1996-00 Vehicles Fig. 3: Turn/hazard flasher location - 1996-00 vehicles 91146g12.gif
The turn and hazard flashers are integrated into one flasher on these models. The flasher is located on a bracket above the brake pedal. Replace the flasher by unplugging the old one, removing it from the bracket, and plugging in the new one.

Oct 08, 2010 | 1998 Chevrolet Cavalier

1 Answer

Left turn signal quit working. 1969 chevy pickup-


sounds like you have a bad flasher which is usually located near the steering column under the dash. check for ground on front left bulb. may have to replace light socket if ground is good.please leave comment.

Mar 20, 2010 | 1983 Chevrolet K1500

1 Answer

Can't find the fuse for the signal lights on 99 expedition


The turn signal flasher assembly is located under the driver's side of the instrument panel, on the front of the fuse panel for the 1997-98 F-250HD, F-350 and F-Super Duty models and under the center section of the instrument panel in the relay/flasher block on all other models.

Also can review the 1999 Ford Expedition Owners Manual (page 132 for Fuse Panel Description); this is in the position 23, 10Amp (Turn/Hazard Flasher and others).

I really hope helps with this (remember rated this help) Good luck.

Dec 23, 2009 | 1999 Ford Expedition

3 Answers

Where does the flasher go on a 98 chevy malibu


Replacement The turn and hazard flashers are integrated into one flasher on these models. The flasher is located in the hazard warning switch and the hazard warning switch is located on the trim plate. Replace the flasher by unplugging the old one, removing it from the panel, and plugging in the new one.
  1. Remove the bezel from the ignition switch.
7f58edd.gif
Remove the bezel from the ignition switch

Carefully remove the instrument panel accessory trim plate.

9f5c3cc.gif
To remove the trim plate, use a suitable prytool to carefully apply pressure at the retaining clip points . . .

bd28884.gif
. . . then gently pull the accessory trim plate away

Detach the electrical connector from the hazard warning switch.

daa6205.gif
Unplug the electrical connector from the hazard warning switch . . .

Unfasten the screw securing the hazard warning switch and remove the switch.

c506713.gif
. . . then unfasten the screw securing the hazard warning switch and remove the switch from the vehicle


Installation is the reverse of removal.

Dec 01, 2009 | 1998 Chevrolet Malibu

2 Answers

Turn signals hazards flasher don't work jeep cherokee replaced combination flasher relay, turn signal switch and still no signals


I NEED TO LOCATE THE SWITCH WHERE IS IT ?
MY INDICATORS NOR HAZARD LIGHTS ARE WORKING I DONT KNOW WHAT IS WRONG WITH IT CHANGED BULBS BUT NOTHIGN THEY ALL WENT OUT AT THE SAME TIME
SO THERE MUST BE A RELAY SWITCH SOMEWHER BUT DONT KNOW WHERE ?
THANKS FOR HELPING

Sep 27, 2009 | 1999 Jeep Cherokee

2 Answers

Where is the turn signal flasher on a 99 alero


THE TURN SIGNAL AND FLASHER ARE TIED IN TOGETHER.YOUR FLASHER SWITCH IS ON THE DASH.ITS A ROUND RED BUTTON WITH A WHITE TRIANGLE ON IT.WHEN YOU PRESS THE RED FLASHER BUTTON ON DASH.IT WILL MAKE YOUR FRONT AND BACK SIGNAL LIGHTS BLINK.WHEN YOU WANT TO TURN OFF FLASHER THEN YOU PRESS THE RED BUTTON.IT WILL TURN OFF FLASHERS.

Aug 10, 2009 | 1999 Oldsmobile Alero

Not finding what you are looking for?
1999 Chevrolet K1500 Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

john h

Level 3 Expert

23577 Answers

Joe Taylor
Joe Taylor

Level 3 Expert

2228 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...