Question about 2004 Hyundai Santa Fe

Open Question

How To Replace Front Sway Bar bushing on 2004 Hyundai santa fe 3.5 L? There is not space to remove the bolts. Do you have any good ideal? Thanks.

Posted by Mobility Lift on

Ad

5 Related Answers

CindyTh

  • 1 Answer

SOURCE: Fog Light Replacement Hyundai Santa Fe

The above statement is GREAT!!! The wheel-well piece folds down across the area you need to be in. There are 2 screws to undo this part. Push it back and there is a cap that unscrews which holds the wires and socket he is talking about. Unscrew the cap, unscrew the wire and housing. The bulb comes out. You pull the wire harness off and install the new bulb. It has a triangular push-in and it has to go just right so take note of how it comes out. Also, being a halogen light bulb, do not touch the bulb with your hands - the oils will make it explode.

Posted on Apr 06, 2009

Ad
goalie39

Ed

  • 479 Answers

SOURCE: ''check engine light'' illuminated, 1004 Hyundai, Santa Fe

If you live in the US, take it to qany Auto Zone store and thy will read the codes off for you, I would suspect any right thinking competitor would do the same, check if you don't have one near by.

Hope this is of some help.
Ed

Posted on Apr 21, 2009

Ad
ghost4548

Paul McGrath

  • 776 Answers

SOURCE: interior fan control knob doesn't work

you have to remove the AC panel from the back side... the virtical console pops out and you can disconnect it (wire harness connectors) to get to it.

Posted on May 31, 2009

Anonymous

  • 87 Answers

SOURCE: 2002 hyundai santa fe front transmission leak

swap w/rear radiator rear doesn't require fluid.

Posted on Jul 28, 2009

Anonymous

  • 84 Answers

SOURCE: Change serpentine belt 2004 Hyundai Santa Fe

it uses a spring loaded tensioner.use a breaker bar to rotate the tension and it should just come off.if u need a pic or anything else to do it let me know,

Posted on Oct 05, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Loud clunk/Knocking noise underneath front end while driving straight
Have the front end inspected by a pro. Possible broken/loose sway bar link...motor mount... control arm bushing.... ball joint.... strut assembly

Apr 25, 2015 | 2002 Hyundai Santa Fe

1 Answer

How hard is it to replace the front sway bar bushings on my 04 camry se
Here are general instructions for replacing this part.
Instructions
    • 1Park the vehicle on a paved level surface. Apply the parking brake and release the hood latch. Place a wheel chock behind of the rear tires and open the hood of the vehicle. This will help to allow some light down into the engine compartment for you when you're underneath it.
    • 2Lift the left front quarter of the vehicle with the floor jack and place a jack stand in a safe and secure location. A front frame rail would be ideal if applicable. Repeat this step for the right front quarter to elevate the front axle.
    • 3. Put on the safety glasses, grab the tools, replacement bushings, and creeper and crawl under the front of the vehicle.
    • 4Locate the sway bar bushings by following the sway bar from the links behind the front tire(s) to where it is mounted to the undercarriage of the car by a bracket. In some vehicles, it may be necessary to remove heat shield, brackets or other components to obtain access to the sway bar brackets for removal. If this is the case, remove anything to help you gain access. The brackets are mounted by one or two bolts. Sometimes the bolt may be steadied with a nut or sometimes it may be screwed into a fixed threaded hole in the undercarriage. Remove the bolts using the ratchet, socket and hand wrench if necessary. One bolt sway bar brackets will have a hinged top or bottom that you'd swing away once the single bolt was extracted.
    • 5Slide the old bushing along the sway bar to a location that's easy for you to extract it from the sway bar. Pry the slotted opening of the bushing using the pry bar to convince it off of the sway bar. The bushing are generally a rubber coated steel bushing so they're going to come off stubbornly. Place the new bushing onto the sway bar in the same fashion. Since they're new, they're going to be even more stubborn than the old one(s).
    • 6Position the bushing back in the correct location on the sway bar and replace the brackets. Tighten with the ratchet, socket and hand wrench as necessary.
    • 7Replace any components that you may have had to remove. Collect all the tools and debris from under the vehicle and crawl out. Lower the vehicle, close the hood, and remove the wheel chock.

Sep 18, 2012 | 2004 Toyota Camry

1 Answer

I need to remove the front hub from a 2005 Santa Fe to replace two lug bolts
that os not nesessary . remobe the caliper and the base and on the base area you have space to remobe one by one.

Sep 02, 2012 | 2005 Hyundai Santa Fe

3 Answers

Safety says i need sway bar bushings.what and where are these?
the sway bar is a bar that runs acrossed the front of the van from strut to strut. It is bolted to the cradel and then has links that run from the bar to the strut to increase stability. The sway bar bushings are rubber mounts that hold the bar down to the cradel. The bar runs though the mounts one each side where the bar and the cradel meet. If they are wore out you will normally hear a clucking noise from the front end when you hit bumps. To remove and replace them there is two bolts that hold a steel cap on top of them on each side. Remove the cap from both sides then the rubber mounts will have a split in them so you can get them off the bar. To install them is just the reverse of the removal. Good luck! 4 thumbs up is appeciated if this helps.

Dec 30, 2010 | 2002 Dodge Caravan

2 Answers

What proper size tires are on a 2004 santa fe
find the options sticker in the vehicl.door frame,glove box good starting places.

Nov 21, 2010 | 2004 Hyundai Santa Fe

1 Answer

How do you replace bushes on sway bar
Remove the bolts on the clamps around bushing where it is bolted to the fram. The bushings are split , you will see when you get them down.

Nov 09, 2009 | 2001 Hyundai Santa Fe

2 Answers

2004 Hyundai Santa Fe 3.5L V6 What all do I have to take off to replace a Crankshaft Position (CKP) sensor
Removal & Installation
  1. Disconnect the negative battery cable.
  2. Disconnect the connector from the sensor.
  3. Remove the retaining bolts.
  4. Remove the sensor from its mounting.
To install:
  1. Installation is the reverse of the removal procedure.
  2. Clearance between the sensor and the sensor wheel should be 0.020–0.059 inch.
Crankshaft Position Sensor The crankshaft position sensor is located at the front of the engine near the timing belt.

30c0fde.jpg

Oct 31, 2009 | 2004 Hyundai Santa Fe

1 Answer

Hyundai santa fe 2004 how can i install two front seat,
2 bolts in each of the seats' floor rails... total of 8. Wire harness connectors may not be the same power seat control harness, seat heaters, etc. Research of connectors shows floor harness connectors are identical between 04 & 05. However, optional features like seat warmers in the wire harness of the 05 model may not exist in the other and vise versa.

Sep 03, 2009 | 2004 Hyundai Santa Fe

1 Answer

I need some guidance as to how to replace the windsheild washer pump on the 2004 Hyundai Santa Fe
unhook the negitive battery terminal, then simply take the bolts out holding the pump on and unplug the wire harness and hose and replace new one. it may be easier if you take out the whole washer tank to get at it. usually 3 bolts.

Aug 08, 2009 | 2004 Hyundai Santa Fe

1 Answer

Wondering if anyone knows what the fuel pressure shoule be on a hyundai santa fe, 2004 4cyl
30 to 50 p.s.i. g. ideally; 45 p.s.i.

May 20, 2009 | 2004 Hyundai Santa Fe

Not finding what you are looking for?

View Most Popular

2004 Santa Fe

  • Cars & Trucks

Related Question

Loud clunk/Knocking noise underneath front end while driving straight

  • 2002 Hyundai Santa Fe

Open Questions:

0 Answers

I have a 2004 Hyundai Santa Fe and I need to change an assembly?

Jan 12, 2019 | 2004 Hyundai Santa Fe

0 Answers

What is the capacity of automatic transaxle fluid for Hyundai Santa Fe 2004

Sep 21, 2018 | 2004 Hyundai Santa Fe

0 Answers

how to remove rear driveshaft from 04 hyundia santa fe

Jul 23, 2017 | 2004 Hyundai Santa Fe

0 Answers

Hyundai Santa Fe 2004 Tracking device Installation. Where to find the constant power source and where to ground? I have a GPS tracking device(TK103 (B) GPS TRACKER) and I need to know where the constant power source is to install the red wire and where to ground the black wire. Any info on this, and where it is accessible would be helpful. Thanks.

Jul 14, 2017 | 2004 Hyundai Santa Fe

See all 2004 Hyundai Santa Fe Questions

2004 Hyundai Santa Fe Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

5 Answers
Car won't start after filling up the gas tank.

2004 Hyundai Santa Fe

2 Answers
Hyundai santa fe starter were

2004 Hyundai Santa Fe

2 Answers
Dome lights don't come on

Hyundai Santa Fe Cars & Trucks

2 Answers
Check the accelerator position sensor on the pedal!

2004 Hyundai Santa Fe

3 Answers
2004 Hyundai Santa Fe problems- Help!

2004 Hyundai Santa Fe

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14866 Answers

Brad Brown

Level 3 Expert

18596 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...