Question about Mazda Cars & Trucks

Open Question

T3500. What is the main bearing crankshaft torque and camshaft torque?

Posted by Mitchell Ricky on

Ad

5 Related Answers

Anonymous

  • 104 Answers

SOURCE: bolt torque for 2004 camshaft and crankshaft gear

if your installing your crankshaft the Torque: 27 N·m (275 kgf·cm, 20 ft·lbf). And for your camshaft the 25mm bolts [2] are 7.5 N·m (80 kgf·cm, 69 in.·lbf) and the rest are 16 N·m (160 kgf·cm, 12 ft·lbf)

Posted on Jun 28, 2009

Ad
hardinfarms

Jerry Hardin

  • 144 Answers

SOURCE: 2003 mazda 6 3.0 need the main bearing torque specs

I'm sending you the torque specifications for your main bearings and also your head bolts. I also sent you main bearing and cylinder head tightening sequence. I hope this will be useful2c713bf.giffce6623.gif
Main Bearings Torque specs. 40-43 Ft. Lbs.
Cylinder Head Torque specs. 56-60 Ft. Lbs.

Posted on Oct 05, 2009

Testimonial: "thank you so much! couldnt find this information anywhere, even called the local mazda dealers!"

Ad
Dirt Dobber

Dirt Dobber

  • 253 Answers

SOURCE: need torque for a 2000 Toyota Celicia GT 1.8L

Crank Main caps Tightening Torque

For the 12 Pointed Head Bearing Cap Sub-Assembly Bolts
Start from center bolts and tighten in a clockwise rotation working out
Step 1 all bolts 22 Nm or 16 ft lb
Step 2 all bolts 44 Nm or 32 ft lb
Step 3 all bolts 45 degrees additional clockwise rotation using an angle indicator.
Step 4 all bolts 45 degrees additional clockwise rotation using an angle indicator.

Hexagon Head Bearing Cap Sub-Assembly Bolts
1ZZ-FE Engine 18.5 Nm (14 ft.lb)
2ZZ-GE Engine 18 Nm (13 ft.lb)

Connecting rod:
1. Apply a light coat of engine oil on the threads and under the heads of the connecting rod cap bolts.
2. Install and alternately tighten the 2 connecting rod cap bolts in several passes. Torque: 1ZZ-FE: 20 Nm (204 kgf-cm, 15 ft. lbs.) 2ZZ-GE: 30 Nm (306 kgf-cm, 22 ft. lbs.) If any of the connecting rod cap bolts does not meet the torque specification, replace the connecting rod cap bolts.
3. Retighten the cap bolts by 90° more
4. Check that the crankshaft turns smoothly.

moz-screenshot.pngmoz-screenshot-1.png

Posted on Mar 19, 2010

Roger Foster

  • 701 Answers

SOURCE: need the crankshaft main bearing torque specs and

Hello tlittle3: My name is Roger and I will help you.See the attached image. Be sure to follow steps as it is very inportant. You will notice that you need to index some of the bolts. That is merely turning the bolt a specified degree. The crankshaft tie bolts are the bolts that are in the side of the block. install horizontal. Shold you need further help please just ask. Please rate the answer you received. Thank You for using Fix Ya. Rogera32a1ae.jpg

Posted on Apr 26, 2010

Testimonial: "thanks that what i needed"

ZJLimited

ZJ Limited

  • 17970 Answers

SOURCE: I need the 2003 Mazda

zjlimited_34.jpg

Fig. Loosen the remaining camshaft cap bolts using this sequence-2.3L (KJ) engine


zjlimited_35.jpg

Fig. Tighten the camshaft cap bolts using this sequence-2.3L (KJ) engine

Posted on Nov 09, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque for nissan patrol 2010 model crankshaft main bearing and camshaft main bearing??thank you!


If you've got it that far apart why haven't you invested in a shop manual? Looks like you need it. Haynes or Chiltons, or possibly an online download.

Sep 27, 2016 | Nissan Cars & Trucks

1 Answer

NEED DIAGRAM FOR LOCATIONS OF CRANKSHAFT PULLY,OIL SLINGER AND SPRING.FOR 1983 MAZDA 2.2L DIESEL


Here is the procedure:-


  1. Remove setscrew from side of cylinder block.


  2. Remove oil pipe attaching bolts.


  3. Remove oil pump and strainer.
TIMING GEAR COVER



  1. Remove timing gear cover to case attaching bolts.


  2. Remove timing gear cover and gasket.

CAMSHAFT, CRANKSHAFT, IDLER & INJECTION PUMP GEARS



  1. Remove oil slinger and washers from crankshaft snout.
Using puller set 49 0839 425C or equivalent, remove crankshaft timing gear, Fig. 3.


  1. Position a clean rag between camshaft and idler gears, then remove cam gear lock bolt and washers.


  2. Using puller set 49 0839 425C or equivalent, remove cam gear from camshaft, Fig. 3.


  3. Remove idler gear to spindle retaining nuts and washers, then remove idler gear and spindle assemblies.


  4. Remove injection pump drive gear.


  5. Remove timing gear case to cylinder block attaching bolts, then the timing case.



CAMSHAFT




  1. Remove tappets from cylinder block.


  2. Remove camshaft thrust plate to cylinder block retaining bolts and washers, then pull camshaft from block.



PISTON & CONNECTING ROD




  1. Remove connecting rod bearing cap retaining nuts and bolts, then separate bearing cap from connecting rod.


  2. Using the wooden handle end of a hammer, push the piston and connecting rod assembly outward until piston rings clear cylinder bore. Remove piston and connecting rod assembly through top of cylinder block.


  3. To separate piston from connecting rod, remove piston pin retaining clips, then press pin from piston using a suitable driver.



CRANKSHAFT




  1. Remove rear oil seal cap retaining bolts, then the cap and seal.


  2. Remove main bearing cap to cylinder block retaining bolts, then the main bearing caps and thrust washers.


  3. Lift crankshaft from cylinder block.



I’m happy to assist further over the phone at https://www.6ya.com/expert/uttamjeet_2f3adc18600f8ede

Mar 26, 2015 | Mazda Cars & Trucks

1 Answer

Torque settings on cranck sharf bearings


Torque settings for V-6 engine.
Main bearing cap bolts torque:
Torque: 27 N·m (275 kgf·cm, 20 ft·lbf)
Mark the front of the main bearing cap bolt with paint.
Re tighten the main bearing cap bolts by 90 degrees.
Check that the crankshaft turns smoothly.

Connecting rod cap bolts torque:
Torque: 24.5 N·m (250 kgf·cm, 18 ft·lbf)
Mark the front of the main bearing cap bolt with paint.
Re tighten the main bearing cap bolts by 90 degrees.
Check that the crankshaft turns smoothly.

Feb 11, 2014 | Toyota Land Cruiser Cars & Trucks

1 Answer

Main bearing cap torque 6g74


Torque Specifications

air intake plenum 11-14 ft lbs.

camshaft bearing cap 14-15 ft lbs.

connecting rod nut 37-38 ft lbs.

camshaft sprocket bolt 66-67 ft lbs.

crankshaft pulley bolt 108-116 ft lbs.

cylinder head bolts 65-72 ft lbs. ( 3.0L) 76-83 ft lbs. (3.5L)

drive plate ( flywheel ) 53-55 ft lbs.

exhust manifold 11-16 ft lbs.

intake manifold 11-15 ft lbs.

main bearing cap 55-61 ft lbs.

rocker shaft 14-15 ft lbs.

valve cover 27-35 in. lbs.

throttle body bolt 84-108 in. lbs.

May 17, 2012 | 1996 Mitsubishi Montero Sport

2 Answers

Rebuilding 4.2 v6 ford need torque spec for main bearing


V8 Engines Component Torque Camshaft Sprocket Bolt 40-45 ft. lbs. Camshaft Thrust Plate-to-Engine Bolts 9-12 ft. lbs. Crankshaft Pulley-to-
Vibration Damper Bolts 35-50 ft. lbs. Cylinder Head Bolts All Except 1993 Flanged Bolts Step 1 55-65 ft. lbs. Step 2 65-72 ft. lbs. 1993 Flanged Bolts NOTE 1 Exhaust Manifold Bolts All Except 1993 HO Cobra 18-24 ft. lbs. 1993 HO Cobra 26-32 ft. lbs. Flywheel/Driveplate-to-
Crankshaft Bolts 75-85 ft. lbs. Intake Manifold Bolts Note 2 Upper Intake Manifold-to-
Intake Manifold Bolts 12-18 ft. lbs. Main Bearing Cap Bolts 60-70 ft. lbs. Oil Filter Insert-to-Engine Adapter Bolt 20-30 ft. lbs. Oil Pan 1979 Step1 Large Bolts 11-13 ft. lbs. Small Bolts 7-9 ft. lbs. Step 2 Large Bolts 15-17 ft. lbs. Small Bolts 10-12 ft. lbs. 1980-87 9-11 ft. lbs. 1988 and up 6-9 ft. lbs. Oil Pick-up Tube-to-Main Bearing Cap Nut 22-32 ft. lbs. Oil Pick-up Tube-to-Oil Pump Bolts 1979-87 10-15 ft. lbs. 1988 and up 12-18 ft. lbs. Oil Pump Bolts 22-32 ft. lbs. Rocker Arm Fulcrum Bolts 18-25 ft. lbs. Thermostat Housing-to-Engine Bolts Through 1987 9-12 ft. lbs. 1988 and up 12-18 ft. lbs. Timing Chain Cover Bolts 12-18 ft. lbs. Valve Cover Bolts 10-13 ft. lbs. Water Pump Mounting Bolts 12-18 ft. lbs. NOTE 1 Step 1 Tighten bolts in sequence to 25-35 ft. lbs. Step 2 Tighten bolts in sequence to 45-55 ft. lbs. Step 3 Tighten bolts in sequence an additional ¼ turn. NOTE 2 Step 1 Tighten bolts in sequence to 23-25 ft. lbs. Step 2 After assembly, retorque all bolts in sequence to 23-25 ft. lbs.let me know if this helps and how about a rating.

Apr 23, 2011 | Ford F-150 Cars & Trucks

1 Answer

I need the 2003 Mazda 6, 2.3 - 4 cylinder main bearing torque specs and sequence asap please.


zjlimited_34.jpg

Fig. Loosen the remaining camshaft cap bolts using this sequence-2.3L (KJ) engine


zjlimited_35.jpg

Fig. Tighten the camshaft cap bolts using this sequence-2.3L (KJ) engine

Nov 09, 2010 | 2003 Mazda Mazda6

1 Answer

2004 mazda 6 3.0L V6 main bearing caps(bootom end) has 16 bolts need torgue specs please!


Okay, the main bearing caps only have 10 bolts, i think your looking for the connecting rod caps, they have 16 bolts, i will list them both, theres a tightening sequnce for the main bearing caps, these are the caps that hold the crankshaft to the engine block, the connecting rod caps hold the pistons to the crank and they have 16 nuts,For a 2004 mazda 6 with the 3.0 engine the torque specs are as follows.
Connecting rod bolts step 1) 19.2 - 23.6 ft lbs.
step 2) tighten an additional 80 - 100 degrees

Main bearing caps step 1) 32.5 - 33.9 ft. lbs.
step 2) tighten an additional 175 -185 degrees.
heres a diagram for main caps to tighten in order.
hope this is helpful.fc3bff9.gif

Aug 20, 2010 | 2003 Mazda Mazda6

1 Answer

V6 T3000 need torque specs has throttle body injector


3.0L and 3.5L V6

Torque Specifications

air intake plenum 11-14 ft lbs.

camshaft bearing cap 14-15 ft lbs.

connecting rod nut 37-38 ft lbs.

camshaft sprocket bolt 66-67 ft lbs.

crankshaft pulley bolt 108-116 ft lbs.

cylinder head bolts 65-72 ft lbs. ( 3.0L) 76-83 ft lbs. (3.5L)

drive plate ( flywheel ) 53-55 ft lbs.

exhust manifold 11-16 ft lbs.

intake manifold 11-15 ft lbs.

main bearing cap 55-61 ft lbs.

rocker shaft 14-15 ft lbs.

valve cover 27-35 in. lbs.

throttle body bolt 84-108 in. lbs.

Aug 15, 2010 | 1994 Mitsubishi Montero

1 Answer

01 mazda protege camshaft torque specs


CAMSHAFT BEARING CAPS TORQUE TO 125 INCH POUNDS. CAMSHAFT SPROCKETS - 44 FT LBS. YOU NEED A REPAIR MANUAL LIKE A CHILTON WITH CAMSHAFT TORQUE SEQUENCE DIAGRAM. YOU HAVE 20 CAMSHAFT CAP BOLTS THAT HAVE TO BE TORQUE IN SEQUENCE.

Mar 21, 2010 | Mazda Protege Cars & Trucks

2 Answers

2003 mazda 6 3.0 need the main bearing torque specs


I'm sending you the torque specifications for your main bearings and also your head bolts. I also sent you main bearing and cylinder head tightening sequence. I hope this will be useful2c713bf.giffce6623.gif
Main Bearings Torque specs. 40-43 Ft. Lbs.
Cylinder Head Torque specs. 56-60 Ft. Lbs.

Oct 05, 2009 | 2003 Mazda Mazda6

Not finding what you are looking for?

Open Questions:

Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14866 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6571 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...