Question about 2010 Ford Escape

Open Question

What is rear axle nut size? - 2010 Ford Escape

Posted by Jay Brown on

Ad

4 Related Answers

alicantecoli

Colin Stickland

  • 22485 Answers

SOURCE: WHAT SIZE SOCKET IS NEEDED

32mm

Posted on Nov 24, 2008


Ian Jones

  • 77 Answers

SOURCE: rear brake drums 1998 ford escort

hi to remove the hob nut you need a large bar about two feet long and i think they are 30mm but you will need to replace them with new ones and torque them correctly or you will encounter problems theyalso have to be pinned when torqued it really is not a diy job

Posted on Feb 04, 2009

Ad
warlock61

warlock61

  • 659 Answers

SOURCE: Axle nut torque spec

184 ft/lb

Posted on May 11, 2009

Bruce Hathcock

  • 3600 Answers

SOURCE: rear axle seal leak 2001 ford escape xlt

First check if the vent cap is plugged, to do that find the T shaped object on the housing spin the top of the tee if it does not move freely then pull it off and clean it. If it's leaking out of the front seal it's the drive line seal is leaking and will have to remove the drive line put Emergency brake on and block wheels and loosen 24MM nut to get to the seal you have to pop the seal off with a screw driver and you have to replace the crush bearing when you do this. However recommend you leave that to a professional or purchase a www.alldatadiy.com susbscription for your car so you know how to set up the bearings if it is needed, you will also have to have a tork wrench to tork the nut down. You will a new Nut for the pintal shaft that comes out of the front of the axle as well the nut is nut reusable once you remove it. Another note you have to have air impact to get the nut off or a torch t heat it just enoungh to get it off but warning fuel tank is right there so if your all thumbs don't mess with it. If it's not leaking from the front seal and is leaking from the back side of the differential then you must drain the oil and replace the gasket on the rear plate, this job is not to difficult but you mus be sue you put silicone on the cover and gasket and put silicone on the bolts as you put them in because if not you will get bolt leakage, these also require a tork wrench. the front seal nut and crush bearing will cost $45.00 the rear will cost $15.00 for the silicone and gasket. And warning if the differtal is leaking from the seal it is quite possible that the bearings will need to be replaced or set up again and this takes experince or it could cost you $750.00 to rebuild the differital. hope this helps.

Posted on Oct 09, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Axle nut size for a corolla 2010


Which axle front or rear?

Jul 30, 2018 | Cars & Trucks

1 Answer

How do I torque spindle nut 2008 escape rear axle


Torque the nut (must be new nut) to 214 foot pounds

Feb 10, 2017 | Ford Escape Cars & Trucks

1 Answer

How to replace 2006 ford escape left front axle shaft


How to Replace a CV Axle on a Ford Escape / Mazda ...

? 9:41
https://www.youtube.com/watch?v=_JxagNLBlQ4
Aug 29, 2013 - Uploaded by klowny1969
Axle nut should be torqued to spec..in the ford escape its around 205-220 lbs ft How To Change An Axle On A Front Wheel Drive Car ! SUBSCRIBE ! ... How to Replace a Front Axle Half Shaft - Duration: 14:37. ... Alternator replacement 2005 2006 Ford Escape 3.0L DOHC All Wheel Drive - Duration: 13:15.

Front axle replacement Ford Escape 2003 Right front CV ...

? 8:46
https://www.youtube.com/watch?v=JQK8SPj6Qsk
Mar 29, 2014 - Uploaded by Fixing cars and stuff
Front axle replacement Ford Escape 2003 Right front CV axle install remove replace This Channel provides ...

Feb 03, 2016 | Ford Cars & Trucks

1 Answer

What size axle nut for 2000ford taurus se


Axle nut size? - Taurus Car Club of America : Ford Taurus Forum

www.taurusclub.com > ... > Suspension, Handling and Brakes
Jul 23, 2011 - 8 posts - ‎5 authors 1996 Mercury Sable front axle nut. I have read that the size is 30mm but the socket that I rented (30mm in a ... 2000 Duratec SE White Wagon Axle nut torque question. - Taurus Car Club of America ...
11 posts
May 4, 2012
CV Axle nut size
11 posts
Dec 9, 2011
Why Does The Axle Nut Need Such A Big Torque
11 posts
Dec 7, 2009
2000 Ford Taurus Front Wheel Bearing And Half-axle ...
11 posts
Apr 18, 2009
More results from www.taurusclub.com

Sep 28, 2015 | Cars & Trucks

1 Answer

Axle nut size


Measure the nut & divide by .0395 to get metric mm

34,35 or 36 mm are the most common

Mar 18, 2014 | Cars & Trucks

1 Answer

How do I replace drivers side front axle on a 2003 Ford Escape ?


remove the right front wheel. remove the axle nut. remove the ball joint bolt and nut. remove the ball joint from the knuckle. drive the axle out of the hub. remove the 2 carrier bearing nuts. pull the axle out. make sure you torque all bolts and nuts.

Sep 17, 2011 | 2003 Ford Escape

3 Answers

What size socket fits the front axle nut on a 2003 ford escape


For a 2002 Escape the hub nut is 32 mm. The torque specification is around 175 ft.-lbs.

Feb 22, 2011 | 2003 Ford Escape

1 Answer

What weight rear axle differential gear oil is required for a ford 2001 escape?


4 wheel drive? size motor? shows either 75-90 or 80-90 depending if its 4 wheel or size motor

Jan 30, 2011 | 2001 Ford Escape

3 Answers

What is the size of the nut on a 05 ford escape, on the crank sha


once you remove the caliper and bracket the rotor comes off. the center nut is for the axle shaft and doesn't get removed.

Jan 10, 2009 | 2002 Ford Escape

Not finding what you are looking for?
2010 Ford Escape Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14866 Answers

Mike

Level 3 Expert

4372 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...