Question about Toyota Prius

Open Question

2010 (2ZR-FXE). What are torque specs and tightening pattern for cam shaft/housing?

Posted by Jesse Torres on

  • Jesse Torres
    Jesse Torres Jan 16, 2021

    Yes, that would be helpful right? I have a 2010 Prius (2ZR-FXE). Thanks.

×

Ad

5 Related Answers

Anonymous

  • 1 Answer

SOURCE: head bolt torque specs and timing marcs for a 94 volvo 960 6cyl

you do 14 foot pounds then 45 foot pounds then a 120 degree turn.if aluminum heads are what you have

Posted on Nov 18, 2008

Ad

Richard Scordino

  • 6982 Answers

SOURCE: Need torque specs for oil pan gasket

There likely is a spec for oil pan but unless you are a finatic, you really don't need to know what it is. Simple rule: Don't crank down ******* any fastener. If corners near crank ends have larger fasteners, you can tighten them a bit more than on siderails. Before tightening anything, install all bolts finger tight, to ensure that they are not cross threaded. To avoid warping pan, tighten from the center of the pan, working towards both ends, alternating from side to side as you go. When you are finished, go over it again, using the same amount of force on each bolt. As I said, end bolts can if larger in diameter, be tightened more but be careful not to tighten so much that you will either split or push the gasket out the sides.. Anywhere two gasket ends **** together, I recommend using a sensor -safe dab of silicone. An oil pan is not under any mechanical stress or pressure. I have used this method for many years and NEVER had one leak. If you really need #s, small fasteners get about 12-15in lbs, larger ones about 20.

Posted on Dec 31, 2008

Ad
chuck943

Chuck Martin

  • 783 Answers

SOURCE: Head bolt torque specs needed for 96 tbird 3.8

Head bolts are torque to yeild so you MUST use new bolts.
Tighten cylinder head retaining bolts in numerical sequence in three steps as follows:

  1. 20 Nm (15 lb-ft).
  1. 40 Nm (30 lb-ft).
  1. 50 Nm (37 lb-ft)
Loosen retaining bolts one at a time two to three revolutions and retighten as follows:

Long bolts:
  • Tighten to 40-50 Nm (30-37 lb-ft).
  • Rotate an additional 175-185 degrees.
  • Go to next bolt in sequence.
Short Bolts:
  • Tighten to 20-30 Nm (15-22 lb-ft).
  • Rotate an additional 175-185 degrees.
  • Go to next bolt in sequence.
Here is a pic of the sequence
http://i253.photobucket.com/albums/hh43/chuck943/Headboltsequence38L.gif

Posted on Mar 19, 2009

Patrick Miller

  • 154 Answers

SOURCE: specs

Well I just looked up the specs for you for the 2.7 ltr. I hope this is what you want.
Cam Caps 105 in.lbs.
Cam Sprocket 250 in.lbs.
Crank Dampener 125 ft.lbs.
Cylinder Head Cover 105 in.lbs.
Here is an illustration of the timing chain set up. Be aware these marks are lined up with the three sets of plated links on the chain. You should easily identify them if you have a new chain. You may have to clean an old chain to see them.
Good luck with this and let me know how it goes for you.
bfc672e.gif

Posted on Apr 06, 2009

Norman Green

  • 312 Answers

SOURCE: 2008 Impala axle shaft torque spec

118 ft lbs

Posted on Jan 11, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will u please help me with cylinder head and cam shafts torque specs for 2013 1.3 toyota corolla 1nr engine


(1) Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.
f050595e03-5f1mvaj5g1pcfjy4nobxv3ia-4-0.png (2) Using several steps, uniformly install and tighten the 10 cylinder head set bolts and plate washers with a 10 mm bi-hexagon wrench in the order shown in the illustration. Torque:
70 N·m {714 kgf·cm, 52ft·lbf} (c) Mark the front of the cylinder head bolts with paint.

a098364e01-5f1mvaj5g1pcfjy4nobxv3ia-4-1.png (d) Further tighten the cylinder head bolts 90° as shown in the illustration.
(e) Check that the paint mark is now at a 90° angle to the front. cam bearing caps; Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.

a098174e07-a-5f1mvaj5g1pcfjy4nobxv3ia-4-3.png Torque:
No. 2 Bearing cap -
30 N·m {301 kgf·cm, 22ft·lbf}
No. 3 Bearing cap -
9.0 N·m {92 kgf·cm, 80in·lbf}

Feb 23, 2018 | Toyota Cars & Trucks

1 Answer

Toyota 80 series GLX auto landcruiser 1996 need head bolt torque a nd cam shaft torque settings


Torque setting Toyota Land-cruiser 80 Series 4.5 1995-98
Engine code: 1FZ-FE, 1HD.
Stage 1: 20 Nm (Start tightening bolts from center to outwards)
Stage 2: 39 Nm
Stage 3: Rotate each bolt by 90 Degrees.
Stage 4: Further rotate each bolt by 90 Degrees

Nov 22, 2014 | 1996 Toyota Land Cruiser

2 Answers

1995 ford windstar thermostat housing bolt torque spec


Most people don't bother using a torque wrench to tighten a thermostat housing.

It is more important to be careful and tighten each bolt a little at a time. You do not want to warp, crack, miss align the part you are bolting.

It does not take a lot of torque to seal a thermostat housing. I would guess somewhere between 15 and 20 ft lbs.

It is often hard to find such torque specs for specific vehicles.

For bolts that you cannot find a specified torque spec, you can refer to a standard bolt torque chart. The charts are based on the diameter of the bolt threads not the wrench size used to fit the bolt head. The charts also depend on the hardness of the bolt material. Also keep in mind the material you are bolting into.

Here is one such chart...
http://www.dansmc.com/torque_chart.htm

Keep in mind that thermostat housing bolts are just sealing a gasket. They are not holding the entire car together.

After turning wrenches for many years, most mechanics just know by feel.

There are cases where a torque wrench is mandatory. Like head bolts, wheel bearing/hub nuts, rod caps, main bearing, etc.

Jul 16, 2014 | Ford Windstar Cars & Trucks

1 Answer

2008 forenza 2.0 cam shaft torque specifications


most likely the torque specs are the same as the other model engine that is in your manual just be sure to tighten them slowly and equally back in forth in small increments because those cam shafts can snap very easily

Jan 02, 2013 | 2008 Suzuki Forenza

2 Answers

I have replaced the stabilizer links on my 2008 Pontiac G6 base model and I cant find the torque specs for the nuts.


Thanks for using FixYa.


Stabilizer Links

Removal & Installation

  1. Raise and support the vehicle.
  2. Remove the front tire and wheel assembly.
  3. Disconnect the stabilizer link from the stabilizer shaft.
  4. Disconnect the stabilizer link from the strut assembly and remove from the vehicle.

To install:
  1. Connect the stabilizer link to the strut assembly.
  2. Tighten the stabilizer link nut to 48 ft. lbs. (65 Nm).
  3. Connect the stabilizer link to the stabilizer shaft.
  4. Tighten the stabilizer link nut to 48 ft. lbs. (65 Nm).
  5. Install the front tire and wheel assembly.
  6. Lower the vehicle.

Mar 04, 2011 | Pontiac G6 Cars & Trucks

1 Answer

Torque spec for 2002 daewoo leganza for half shaft nut


THE LEGANZA MODELS TIGHTEN THE HALF SHAFT NUT TO 111 - 155 FT LBS .LOOSEN THE NUT RETIGHTEN TO 37 FT LBS.RETIGHTEN AN ADDITIONAL 60 DEGREES.STAKE THE NUT WITH A PUNCH AND HAMMER.THE NUT WILL NOT BE LOCKED IN PLACE UNTIL THE NUT HAS BEEN STAKED.

May 13, 2010 | 2002 Daewoo Leganza

1 Answer

Hello. Could you please advise me what the camshaft torque tightening specs are for a 1993 SEAT IBIZA . Thank you


CAM SHAFT BEARING CAPS 15 FT LBS. DRIVE SPROCKET BOLT 58 FT LBS. CAMSHAFT END PLAY IS 0.006 in. WARNING THIS IS THE 2.8L ENGINE WHEN TORQUEING CAM SHAFT BEARING CAPS YOU HAVE TO TIGHTEN THE BOLTS 2 TURNS AT A TIME IN A DIAGONAL PATTERN TO DRAW THE CAMSHAFT DOWN AGAINST THE VALVE SPRING.

Sep 29, 2009 | 2002 Volkswagen Golf

1 Answer

What is torque spec for 2004 Ford 4.0 thermostat cover bolts? Replaced black ''plastic'' thermostat housing and inlet cover. Thanks


Normally these bolts are about 20-24ft lbs. You don't want to over tighten them as they should have a rubber washer/gasket to help provide a good seal. These cast aluminum housing will easily strip so just use care when tightening. Just snug both bolts and run the vehicle til it reaches operating temp then check for leaks. You can also purchase a Chiltons/Haynes manual for your vehicle at any auto parts store for $15 they normally give you the torque specs as well as some other valuable tipe

Aug 06, 2009 | 2004 Mercury Mountaineer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14866 Answers

Mike

Level 3 Expert

4372 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...