Question about Ford Cars & Trucks

1 Answer

How to set timing on a ford 1.6 engine duratec. Belt broke cant see the timing marks on the cam pulleys

Posted by Donald Mvukela on

Ad

1 Answer

Arnie Burke

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,517 Answers

Library has chilton n mitchell shopbooks

Posted on Dec 03, 2020

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine Timing marks on a 4.0 ford ranger on a 2005


Rotate the engine so that No. 1 cylinder is at TDC on the compression stroke. Check that the timing marks are aligned on the camshaft and crankshaft pulleys. An access plug is provided in the cam belt cover so that the camshaft timing can be checked without removal of the cover or any other parts. Set the crankshaft to TDC by aligning the timing mark on the crank pulley with the TDC mark on the belt cover. Look through the access hole in the belt cover to make sure that the timing mark on the cam drive sprocket is lined up with the pointer on the inner belt cover.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/ernie_b93ee48ba0eab50b

Nov 02, 2011 | 2005 Ford Ranger

1 Answer

Need timing blet diagram 1992 ford ranger 2.3


Hi, the crankshaft marks are on the belt pulley and timing cover, so you have to mate it up to see them. The cam sprocket mark goes on the bottom, and aligns with another mark on the timing cover. There is a plug you pull out and hole to look thru to align the cam sprocket/shaft.


jturcotte_1801.gif


jturcotte_1802.gif


Rotate the engine so that No. 1 cylinder is at TDC on the compression stroke. Check that the timing marks are aligned on the camshaft and crankshaft pulleys. An access plug is provided in the cam belt cover so that the camshaft timing can be checked without removal of the cover or any other parts. Set the crankshaft to TDC by aligning the timing mark on the crank pulley with the TDC mark on the belt cover. Look through the access hole in the belt cover to make sure that the timing mark on the cam drive sprocket is lined up with the pointer on the inner belt cover.

Jun 01, 2011 | Ford Ranger Cars & Trucks

1 Answer

How do you set the timming on a 2.3 when your putting the new timming belt on


The IGNITION timing on your Ranger is computer-controlled and is not adjustable.


Should the camshaft drive belt/timing belt jump timing by a tooth or two, the engine could still run; but very poorly. To visually check for correct timing of the crankshaft, auxiliary shaft, and the camshaft follow this procedure:
There is an access plug provided in the cam drive belt cover so that the camshaft timing cam be checked without moving the drive belt cover.
  1. Remove the access plug.
  2. Turn the crankshaft until the timing marks on the crankshaft indicate TDC.
  3. Make sure that the timing mark on the camshaft drive sprocket is aligned with the pointer on the inner belt cover.

Never turn the crankshaft of any of the overhead cam engines in the opposite direction of normal rotation. Backward rotation of the crankshaft may cause the timing belt to slip and alter the timing.
REMOVAL & INSTALLATION

See Figures 1, 2 and 3


0996b43f80211842.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Timing belt cover on the 2.3L and 2.5L engine


0996b43f80211843.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Timing belt assembly on the 2.3L and 2.5L engine


0996b43f80211844.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Releasing the timing belt tensioner using a special tool

  1. Rotate the engine so that No. 1 cylinder is at TDC on the compression stroke. Check that the timing marks are aligned on the camshaft and crankshaft pulleys. An access plug is provided in the cam belt cover so that the camshaft timing can be checked without removal of the cover or any other parts. Set the crankshaft to TDC by aligning the timing mark on the crank pulley with the TDC mark on the belt cover. Look through the access hole in the belt cover to make sure that the timing mark on the cam drive sprocket is lined up with the pointer on the inner belt cover.

Always turn the engine in the normal direction of rotation. Backward rotation may cause the timing belt to jump time, due to the arrangement of the belt tensioner.
  1. Drain cooling system. Remove the upper radiator hose as necessary. Remove the fan blade and water pump pulley bolts.


Dec 11, 2010 | 1995 Ford Ranger Supercab

1 Answer

Timing belt broke ,just replace it but it won`t crank.it sounds like electric priblem


Only the 2.3 liter diesel is an interference engine. The 2.3 Liter gas is not an interference engine. I would guess the belt was not installed correctly. The belt broke so the cam was then out of alignment with the crankshaft. Unless you aligned it correctly it will not start. BTW, the belt must be replaced every 60,000 miles. I asume you have the timing cover off, put it back on and set the crankshaft at the 0 mark on the timing cover, remove the cover and don't touch the crank. near the bottom of the cam gear is a protruding piece of plastic with three raised areas, set the cam timing mark at the first pointer, closest to the passenger side . on the back part of the timing cover is a v shaped pointer set the distributor gear mark at the pointer, remove the distributor cap and verify that the rotor is pointing at #1. Loosen both bolts on the tensioner and using a pry bar carefully pry the tensioner away from the distributor gear, tighten the small bolt on the tensioner. install the new belt starting at the crank, then the distributor gear, then the cam, then over the tensioner pulley. loosen the small bolt and the tensioner will adjust automatically. tighten the tensioner bolts and turn the engine over by hand 2 or 3 times and make sure all marks line up ( the cam mark should now be at the center pointer with the crank at 0). I find it handy to paint a reference mark for the crank inside the timing cover.

Mar 16, 2010 | 1995 Ford Ranger Supercab

2 Answers

Need a picture of the crankshaft and cam shaft alignment marks


Fig. 1: Timing marks are located on the camshaft pulleys as shown-1.8L engines

72dd798.jpg

Fig. 2: Make sure that the crankshaft sprocket (timing belt pulley) and oil pump timing marks are aligned-1.8L engines

a41ca11.jpg

Fig. 3: Align the timing belt pulley mark with the tension set mark, at approximately the 10 o'clock position-1.8L engines

2022a8b.jpg

I hope helps with this (reemmber rated this help) Good luck.

Dec 29, 2009 | 1997 Ford Escort

1 Answer

Timing belt broke. Is this an interferance engine?


your in luck this is a freewheeling engine and should have no engine trouble after the new belt goes on.looking at the belt side the cam pulley marks line up at the bottom towards the right and the crank towards up to the right just look for the marks on the pulleys and block.Good luck let me know how it went.

Jun 03, 2009 | 1993 Ford Mustang

2 Answers

Trying to set timing but cant figure out how to set top of timing


here is the entire procedure tart to finish.
Required tools:
13mm open end wrench 10mm shallow and deep socket 8mm socket long flathead screwdriver 17mm deep socket T50 torx socket 1/4", 3/8ths and 1/2" ratchets and extensions E10 inverted torx sockets 6mm Allen wrench 15mm open end wrench 7mm socket 12mm open end wrench 14mm socket 12mm socket 8mm, 9mm and 10mm Allen head sockets 19mm socket pry bar needle nose pliers
If you are doing this because your timing belt broke you will also need to buy a complete cylinder head, head gasket set, and both idler pulleys. ALL DAEWOO MODELS WILL BREAK THE INTAKE AND EXHAUST VALVES WHEN THE TIMING BELT BREAKS.
Start by removing the air cleaner assembly from the throttle body, remove the air filter and housing jack up the vehicle and remove the wheel, remove the plastic shielding in front of the accessory drive belt assembly, remove the accessory drive belt, place a jack with a block of wood on top underneath the engine oil pan remove the front engine mount, remove the crank shaft pulley ( the 4 Allen head bolts only not the 17mm bolt in the center.) remove the metal plate behind the engine mount bracket on the engine, remove the plastic timing belt cover 3 clips on top 2 10mm bolts on bottom. Rotate the engine until the #1 cyl. is at Top Dead Center on the compression stroke or line up the crankshaft timing mark with the mark on the inner timing belt cover ( notch in cover with notch in pulley) on the camshaft pulleys -- ( intake cam line up the line on the pulley with the line on the inner cover)( exhaust cam line up the arrow on the pulley with the arrow on the inner cover) loosen the 13mm bolt in the belt tensioner and using the Allen wrench rotate the tab until there is slack in the belt. Remove the belt. At this time I would recommend you replace the water pump, both plastic idler pulleys as they tend to overheat and lockup, and the belt tensioner. Make sure all your marks are lined up, you may need a helper to hold the Exhaust Cam in place as it tends to move during belt installation. Put the timing belt underneath the crankshaft pulley, install the belt leaving the intake cam for last and NO BELT SLACK on the right side between the crank and the exhaust cam. Once the belt is installed rotate the crankshaft over 2 revolutions and make sure is rotates freely, and your timing marks are aligned perfectly if not the engine will not run properly, tension the belt as needed. Installation is the same as removal.

To clarify, on the DOHC engine, the intake cam gear has a line on it, and the exhaust cam gear has an arrow on it. These should be lined up with the corresponding line and arrow on the VALVE COVER, pointing straight up. I just went through this process over the weekend, and spent quite a bit of time looking for these marking as I had removed the valve cover. Once I found them, it was plain and simple.
In addition, be sure to not over tighten the belt when reinstalling. The tensioner has markings on it for "old" and "new". DO NOT adjust past "new", as the car will sound like a jet engine, and the belt will not last for very long.
One more item that you may as well replace while you are in there is the cam position sensor if you have not already, as there have been issues with them, and the timing housing has to be opened to get to it

Apr 07, 2009 | 2001 Daewoo Lanos

1 Answer

My timing belt broke on my '99 Ford Escort ZX2. Please tell my husband how to replace it. Than k you



 
 
Timing Belt
REMOVAL & INSTALLATION
1.8L Engine
Disconnect the negative battery cable.
Remove the timing belt covers.
Rotate the crankshaft and align the timing marks located on the camshaft pulleys and the seal plate.
Remove the crankshaft pulley and hub.
If the timing belt is to be reused, mark an arrow on the belt to indicate its rotational direction to enable correct re-installation.
Loosen the timing belt tensioner lockbolt and remove the timing belt.
To install:
Temporarily secure the timing belt tensioner in the far left position with the spring fully extended, then tighten the lockbolt.
Make sure the timing marks on the timing belt pulley (crankshaft sprocket) and the engine block (oil pump housing) are aligned.
Make sure the timing marks on the camshaft pulleys and the seal plate are aligned.
Install the timing belt.
Loosen the tensioner lockbolt. Using a suitable prying tool, position the timing belt tensioner so the timing belt is taut, then tighten the tensioner lockbolt.
Turn the crankshaft two turns clockwise and align the timing belt pulley mark with the mark on the engine block.
Fig. 1: Timing marks are located on the camshaft pulleys as shown — 1.8L engines


 
Fig. 2: Make sure that the crankshaft sprocket (timing belt pulley) and oil pump timing marks are aligned — 1.8L engines


 
Fig. 3: Align the timing belt pulley mark with the tension set mark, at approximately the 10 o'clock position — 1.8L engines


 
Fig. 4: Check the timing belt deflection at the location shown — 1.8L engines

Mar 28, 2009 | 1999 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14852 Answers

Mike

Level 3 Expert

4372 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...