Question about Suzuki Cars & Trucks

1 Answer

2013 Swift. How many camshaft position sensors does it have?

Posted by Neil Preskey on

Ad

1 Answer

Simon Atkinson

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Suzuki Master
  • 1,893 Answers

There is usually One for each cam shaft fitted. Most Suzuki engines are "twin cam". This means there will be 2 on your engine.

Posted on Dec 01, 2020

Ad

5 Related Answers

davesmith_37

dave smith

  • 94 Answers

SOURCE: P0340 Code Camshaft Position Sensor


The Camshaft Position (CMP) Sensor detects the position of the camshaft in order to identifiy when piston No. 1 is on its compression stroke. The CMP sensor is used for ignition timing in the Ford DIS igntion system, but not in the EDIS igntion system. Both DIS/EDIS use the CMP signal for synchronizing the firing of sequential fuel injectors.

On the 3.0L vulcan engine, the CMP signal is generated by a single Hall-Effect magnetic switch, activated by a single "vane" spinning around by virture of a synchronized shaft which is driven by the camshaft. 

The CMP sensor & synchronizer/shaft are located behind the intake manifold (i.e., back near the firewall on a Ranger) on the top of the cylinder block. If you just need to replace the sensor, it is a simple job of unplugging the electrical connector and removing the screws holding the sensor in place. Here is a sketch of the sensor to give you an idea what to look for:

Posted on Feb 27, 2009

Ad

Anonymous

  • 218 Answers

SOURCE: Camshaft Position Sensor Location

IF U GO TO THE RIGHT SIDE OF THE ENGINE AND LOOK 4 INCHES BEHIND THE BELT IT WILL BE ON TOP OF THE TIMING COVER.THE WIRES WILL BE RED/WHITE,BLACK,BROWN/WHITE

Posted on May 05, 2009

Anonymous

  • 1 Answer

SOURCE: camshaft position sensor

The camshaft position sensor is on the rear cylinder head on the left end (the serpentine belt end of the engine - passenger side). It is a son-of-a gun to get at. When it is bad or the connector is intermittant or bad, the symptom will be irregular idle from 500 to 750 RPM or so.

Posted on Aug 22, 2009

bs77bird

  • 144 Answers

SOURCE: Where is the camshaft position sensor located in a 2001 VW Passat

when you are looking at the engine pull off the plastic cover on top then the front cover that covers you timing belt there is a wire harness tha goes right to it in the left upper coner two ten mil bolts and it comes off careful not to drop bolts down in belt that could be bad. it is that easy

Posted on Sep 01, 2009

ZJLimited

ZJ Limited

  • 17970 Answers

SOURCE: Where is camshaft position sensor on 2001 Saturn

Hi there:
This vehicle doesnt have a camshaft position sensor, it uses the crankshaft position sensor .. image link HERE.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Posted on Aug 24, 2012

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the intake camshaft position sensor located on a 2013 Malibu 2.4 ecotec?


P0010, P0011 (Intake/Exhaust Camshaft Solenoid) 2013 Chevy Malibu
https://www.youtube.com/watch?v=-RhsWasBAXA
Replacing a Camshaft Position Sensor on a Chevrolet 2.4 Ecotec P0340
https://www.youtube.com/watch?v=uF9l2gtDYIk
GM 2.4 Ecotec Camshaft Position Sensor - How To Test & Replace
https://www.youtube.com/watch?v=dOvwSncdP0g
2011 Chevy Malibu 2.4 camshaft senors location
https://www.youtube.com/watch?v=YCNRrv4r2Uk
2013 Chevy Malibu P0014
https://www.youtube.com/watch?v=VLNnc8v8TVw




Sep 06, 2018 | Cars & Trucks

2 Answers

Where is the crankshaft position sensor on my 2010 srx 3 liters


Camshaft/Crankshaft Position Sensor Replacement - Cadillac Forums

www.cadillacforums.com/.../261074-camshaft-crankshaft-position-senso...

May 29, 2012 - 8 posts - ‎4 authors
I have a 2004 CTS - 3.6L and am trying to get the camshaft position ... at my local Auto Zone and it simply shows camshaft position sensor A. Code P0340 Camshaft Position Sensor
14 posts
Mar 23, 2013
How to change the camshaft and crankshaft position ...
6 posts
Oct 9, 2011
Where is camshaft position sensor on 2003?
7 posts
Dec 28, 2009
Crankshaft Position Sensor 3.6L 04 CTS
5 posts
Jul 15, 2008
More results from www.cadillacforums.com

2004 Cadillac DTS crankshaft position sensors - YouTube

? 3:22
https://www.youtube.com/watch?v=jbjLJZzF3xA
Sep 16, 2013 - Uploaded by Rogelio Cervantes
Quick overview crankshaft position sensor replacement for a 2004 Cadillac DTS 4.6 liter North Star. ... 2003 Cadillac CTSCrank Position Sensor Part 3 Done!!! - Duration: 8:21. 2LateIWon 8,433 views. 8:21. How To Check .

Jan 16, 2016 | Cars & Trucks

2 Answers

Where is the location of the camshaft position sensor ? aka: CMP.


images for 1997 geo metro camshaft position sensor

1993 Geo Metro Camshaft Position Sensor Unraveled ...

? 5:18
www.youtube.com/watch?v=XXA1yFePM4w
Apr 8, 2015 - Uploaded by Jeff Dean
This is Part One of a series where I document my troubles with the Camshaft Position Sensor. This first

Sep 18, 2015 | 1997 Geo Metro

1 Answer

2001 ignis gl manual overhreating


Camshaft position sensor. I had the exact same problem. I changed it and it never stalled again.

Dec 18, 2013 | 2001 Suzuki Swift

2 Answers

P2135 07 Suzuki swift


fly by wire.
Throttle body failure, clean it and pray.
bad TPS wires at same place.
- Faulty electric throttle control actuator (TP sensor 1 and 2)
- Throttle Position Sensor harness is open or shorted
- Throttle Position Sensor circuit poor connection
- Faulty accelerator pedal position sensor
http://helpforcars.net/obd_codes/p2135_suzuki.html

Oct 15, 2013 | Suzuki Cars & Trucks

1 Answer

P0340 and Tach doesn't work


this is easy, 340 is fully cover here
http://www.alldata.com/
Camshaft Position (CMP) Sensor Circuit
the sensor is bad/dead or intermittent.
the modern engines, (some) can run a while with one or both RPM
sensors bad.(not both same time)
there are 2, the CMP and the CKP.
crank, and cam in english.
on some cars, the ECU goes to limphome when one dies.
btw , both need to work for OBD2 MISFIRE to work.
use alldata, look up the code for your year, then look up
Diagnosing, CMP ,

some cmp on suzuki are very smart, they have dual sensors inside.
this allows limp home to work better.
the cmp is at the rear of the cam on most suzuki.

Apr 29, 2013 | 2006 Suzuki Swift

1 Answer

Suzuki swift 1.3 single OHC runs fine when cold,


Check the valve timing.You might have some problems with your timing belt or camshaft sprocket. If timing is OK, check the resistance of your TP sensor, specially on the terminals for full throttle. Resistance should be 2 to 6.5 kilo ohms. Lower than this the ECM will not give the right avance ignition timing to your engine. Repositioning the mounting angle may correct the problem.

Apr 23, 2009 | 1993 Suzuki Swift

1 Answer

Vechile is getting no spark!


Is the ignition coil good (primary and secondary coil resistance alright)? Did the ignition unit (IGBT) passed the 3V battery test? If so, you may have an ECM problem.

Apr 20, 2009 | 1992 Suzuki Swift

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14852 Answers

john h

Level 3 Expert

23515 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...