Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Axle shaft will not pull out of hub 2007 Monte carlo ss hub is released from housing, can not get it to slide off of the shaft. Did one side no problem, other side wont release.

2 Answers

The jack of all trades

Expert 145 Answers
Posted on Nov 30, 2020

The jack of all trades

Expert

Joined: Nov 14, 2020

Answers

145

Questions

Helped

41686

Points

407

May need to remove brake caliper and remove two bolts from upper control arm at bottom of strut to get rotar to flex down enough to remove the shaft completely if it just stuck then like other suggested replace nut back wards and hit with hammer to break loose

Rocky

Cars & Trucks Master 341 Answers
Posted on Nov 30, 2020

Rocky

Cars & Trucks Master

Joined: Apr 04, 2014

Answers

341

Questions

Helped

41941

Points

1619

Spray some lubricant...put the nut back on it enough to cover the treads and hit it with a hammer

Rocky Nov 30, 2020

Something like this

Something like this

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

0helpful

1answer

How to front trans axle seal 1998 Monte Carlo

you have to pull the half shaft out on the side the seal is leaking then pop out the seal and install new seal. this means r&r the wheel, brake, separate the lower ball joint, remove the half shaft axle nut, remove the half shaft from the spindle and pull out half shaft from trans. install in reverse order.

Read full answer

Jul 10, 2015 • Cars & Trucks

0helpful

1answer

Humming sound coming from rear drivers side of 97 Monte Carlo LS

Check axle hub bearings they could be worn out

Read full answer

Apr 15, 2014 • 1997 Chevrolet Monte Carlo

0helpful

1answer

How to remove clip on shift lock on a 2006 Monte Carlo

I was having the exact same issue with my monte carlo ss just this week.

You obviously have taken it all apart so you can now see the harness. The release for the clip is situated in a difficult place.

There is a 1.5 inch thin strip of plastic that covers the shifter shaft. Slide this up and either use an elastic band or tape it to the shifter, just to hold it up and out of the way.

Now shine a flash light down and to the right and you will see the back of that stupid gray clip. Use a flat head or some thing similar to dislodge the clip.

Now you will have to remove the blue things on the clip and remove the old broken wire out of the harness. Make sure you document which colored wire goes where.

You will however have to attach new terminals to the ends of the wires before inserting them into the harness again. You can purchase these from any auto parts place. (I just grabbed some from my friend's shop.)

Read full answer

Jan 19, 2012 • 2006 Chevrolet Monte Carlo

1helpful

1answer

How do I remove the bearing pack from the front driver side of a 2007monte carlo??

Loosen the 32mm axle bolt (size varies) while the wheel is still on the ground so you can loosen it, then there are three hub retaining bolts from the back that are 13mm i think, then you can use a hub puller and some persuasion to get it off the axle. and the three bolts have loctite, you might wanna replace them with new. ....

Read full answer

Oct 27, 2011 • 2007 Chevrolet Monte Carlo

11helpful

3answers

How to replace rear Axle seal on 4x4 chevy

this is very hard if you do not know what you are doing. Ill try to step you through this

pull wheels
drain pun-kin case
pull rear cover
in between the spider and axle sets pull C ring with needle nose pliers
pull hub and axle out CAREFULLY as there are roller bearings on the end of the axle housing
pull seal out at the end of axle housing
tap in new seal CAREFULLY and straight DO NOT BEND IT or it will be junk
replace axle carefully as the roller bearings are still there
replace C clip to original position
replace axle diff cover and replace the gasket with a new one
refill diff case
install tire
your good to go

Read full answer

May 03, 2010 • 2002 Chevrolet Silverado

0helpful

1answer

How to replace front passenger side barings?

take off wheel. remove tie rodend, remove control arm at ball joint. remove axle nut pull axle out of hub, take brake caliper and rotor off should be bolts holding hub in place.

Read full answer

Feb 05, 2010 • 1997 Chevrolet Monte Carlo

1helpful

1answer

Fix front wheel bearing 2001 monte carlo ss

Remove the wheel, remove the axle nut, remove the brake caliper and bracket, remove the brake disc, remove the three bolts that go through the back and hold the bearing assembly in the knuckle, disconnect the abs connector and slide the bearing assembly out. Reverse the procedure to install the new one.

Read full answer

Jan 07, 2010 • 2001 Chevrolet Monte Carlo

0helpful

1answer

ABS and Traction control warning lights come on independtly and jointly. I believe the problem is the hub mounted sensor. How do I replace it.This is on a 2003 Monte Carlo SS.

hi if you know for sure it's a wheel speed sensor
remove that wheel
remove the caliper and caliper bracket
remove the brake rotor
there are 3 bolts on the other side of the knuckle(13mm)
remove them
remove the axle nut(1 5/16)
remove the hub bearing assembly(you may need to use a hammer on the hub flange)
hope this helps

Read full answer

May 25, 2009 • 2003 Chevrolet Monte Carlo

2helpful

2answers

Rear end

Did you pull the pin at differential just to be sure? If it's non-"C" clips, you'll need a slidehammer attached to hub, over studs & use wheel nuts to hold it on there. Get er done !

Read full answer

Apr 24, 2009 • Chevrolet Monte Carlo Cars & Trucks

0helpful

3answers

Removing front axle 1991 ford escort

do you mean the drive shaft. if so you just need a good lever bar to prise the drive shaft out of the transmission.if you mean you want the drive shaft out of the front wheel hub then you may need a good pller to femove it as it can be very tight on the splines

Read full answer

Apr 22, 2009 • 1995 Ford Escort

Not finding what you are looking for?

View Most Popular

Cars & Trucks

How to front trans axle seal 1998 Monte Carlo

Cars & Trucks

35 views

Ask a Question

Usually answered in minutes!

Related Topics:

Trustworthy Expert Solutions

Axle shaft will not pull out of hub 2007 Monte carlo ss hub is released from housing, can not get it to slide off of the shaft. Did one side no problem, other side wont release.

2 Answers

The jack of all trades

Rocky

Add Your Answer

Attachments: Added items

Related Questions:

How to front trans axle seal 1998 Monte Carlo

Humming sound coming from rear drivers side of 97 Monte Carlo LS

How to remove clip on shift lock on a 2006 Monte Carlo

How do I remove the bearing pack from the front driver side of a 2007monte carlo??

How to replace rear Axle seal on 4x4 chevy

How to replace front passenger side barings?

Fix front wheel bearing 2001 monte carlo ss

ABS and Traction control warning lights come on independtly and jointly. I believe the problem is the hub mounted sensor. How do I replace it.This is on a 2003 Monte Carlo SS.

Rear end

Removing front axle 1991 ford escort

Not finding what you are looking for?

Cars & Trucks

How to front trans axle seal 1998 Monte Carlo

Ask a Question

Check Out the Latest Top Trucks Report!

Top Cars & Trucks Experts

ZJ Limited

john h

Arnie Burke

Are you a Car and Truck Expert? Answer questions, earn points and help others

Manuals & User Guides

DIS9_Full.pdf. user-manual-1994...

DIS9_Full.pdf. user-manual-1994...

Rhonda_Docs.pdf. user-manual-2001...

Related Topics:

Trustworthy Expert Solutions

Axle shaft will not pull out of hub 2007 Monte carlo ss hub is released from housing, can not get it to slide off of the shaft. Did one side no problem, other side wont release.

2 Answers

The jack of all trades

Rocky

Add Your Answer

Attachments: Added items

Related Questions:

How to front trans axle seal 1998 Monte Carlo

Humming sound coming from rear drivers side of 97 Monte Carlo LS

How to remove clip on shift lock on a 2006 Monte Carlo

How do I remove the bearing pack from the front driver side of a 2007monte carlo??

How to replace rear Axle seal on 4x4 chevy

How to replace front passenger side barings?

Fix front wheel bearing 2001 monte carlo ss

ABS and Traction control warning lights come on independtly and jointly. I believe the problem is the hub mounted sensor. How do I replace it.This is on a 2003 Monte Carlo SS.

Rear end

Removing front axle 1991 ford escort

Not finding what you are looking for?

Cars & Trucks

How to front trans axle seal 1998 Monte Carlo

Ask a Question

Popular Questions

Toyota dashboard CD player won't eject

4.3 Firing order diagram for 4.3L v6 Chevy engine

BMW X5 Trans Fail Safe Program,

Diagram of 1996 ford ranger fusebox which fuse is

What does my check engine light trouble code $7e8 mean?

Check Out the Latest Top Trucks Report!

Top Cars & Trucks Experts

ZJ Limited

john h

Arnie Burke

Are you a Car and Truck Expert? Answer questions, earn points and help others

Manuals & User Guides

DIS9_Full.pdf. user-manual-1994...

DIS9_Full.pdf. user-manual-1994...

Rhonda_Docs.pdf. user-manual-2001...