Question about Jeep Cars & Trucks

1 Answer

How to bleed a clutch on a 1993 jeep wrangler,step by step

Posted by Kevin jones on

  • Kevin jones Jul 08, 2020

    Thank you for the information, and I appreciate your support

  • Mike Duffy
    Mike Duffy Jul 08, 2020

    No problem, I forgot to say to keep the reservoir full

×

Ad

1 Answer

Mike Duffy

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 904 Answers

I think this will help you, have someone pump the pedal several times then hold pedal to the floor while you loosen the bleed screw at the end of the line and after a second tighten the bleed screw then pump pedal, continue this until only clear dot3 fluid without bubbles comes out. Take care
How to bleed a clutch on a 1993 jeep wrangler,step - 1651f622-069d-443f-8d6c-46e1286ab66c-undefined-undefined-0.gif

Posted on Jul 08, 2020

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After changing transmission and clutch in 91 Wrangler, clutch goes to floor. Tried bleeding line but didn't work.


The clutch should go to the floor =) But if it's not disengaging the clutch disk, there's definitely a problem between the pedal and the clutch disk. I'm guessing you have a hydraulic clutch?

Apr 19, 2012 | 1991 Jeep Wrangler

1 Answer

Where do you bleed the clutch at on a 1997 jeep wrangler what is the location of it


This all depends if this is a hydraulic clutch or if its cable operated, you can only bleed hydraulic clutches, to bleed it you would bleed at the ******, you will see the bleeder screw on the slave cylinder that operates the clutch fork.

Sep 03, 2011 | 1991 Jeep Wrangler

1 Answer

My 1993 jeep wrangler clutch keeps giving out even after i bleed the line..any thoughts? it works fine for a little while then goes to the floor again


replace the CLUTCH MASTER and SLAVE assembly! Age of that classic jeep needs NEW CLUTCH MASTER and SLAVE! That part together w/ clutch slave should be change! Personally i have experience replacing the kit only, it didn't last longer than expected and even got me in trouble, and I spend like i bought a NEW one! So its up to you to decide? taaah!

Nov 10, 2010 | 1995 Jeep Wrangler

1 Answer

Clutch is soft and at time gears grind when shifting my 93 Jeep Wrangler


might need to bleed the clutch hydraulics. good luck!

Nov 06, 2010 | 1993 Jeep Wrangler

1 Answer

How do you do you bleed a clutch line on a 1993 jeep wrangler?


Just like you would bleed brakes. Fill the reservior with brake fluid, open the bleeder screw and have a friend press the clutch pedal in. Close the bleeder screw and let up on the clutch. Do that until the clutch pedal has a good feel. Be sure to check the reservoir frequently as they don't hold much fluid and if you let it get low you'll **** more air into the system.

Jul 31, 2010 | 1993 Jeep Wrangler

1 Answer

1993 jeep cherokee clutch


Take a turkey baster or similar item and **** the fluid out of the clutch master, refill it. Then open the bleed valve on the slave cylinder, have someone step down on the clutch, close valve. Repeat several times till fluid is clean coming out. Do not permit the master to run dry while bleeding. Top off when finished.

Apr 29, 2009 | 1993 Jeep Cherokee Country

1 Answer

Brake fluid seems to be full


bleed brake lines they have air in them

Mar 21, 2009 | 1993 Jeep Wrangler

2 Answers

1991 jeep wrangler not shifting into gear could this be clutch


I would first bleed the tranny lines, if that doesnt work then your tranny is out and need to get it replaced. FYI with Jeep Wranglers, It is better to get a new transmission then to rebuild them

Feb 09, 2009 | 1991 Jeep Wrangler

1 Answer

Push down on clutch pedal can't get car into gear


Likely, you have a hydraulic clutch system. Check clutch master cylijnder for fluid and leakage, check hydraulic line and slave cylinder for leaks. If fluid low or empty, bleed as you would a brake wheel cylinder. If full,have someone work the clutch while you watch slave cylinder to make sure it is moving clutch fork. If system full and little or no movement, the master may be "bypassing" internally (replace) Also, check pedal mechanical linkage. Not often but sometimes these parts can break! Could also be athat clutch itself is worn, but this does not happen overnight and you would have noted slip long before this!

Dec 29, 2008 | 1993 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...