Question about Cars & Trucks

1 Answer

When trun on i have t ajust the blub t get it to come on and it might stay on for a while or just foe a short time till i have to do it again

Posted by brenda on

Ad

1 Answer

ray gallant

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 66,956 Answers

Go see a good mechanic perhaps he or she will know what you want to know .

Posted on Mar 26, 2020

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Horn&trunsigle &wipers quit working


Since all three work independantly of each other, you have a short somewhere. Replace all fuses and see if they short out again. If so, you need to find the short before putting in the fuses again.

Sep 11, 2012 | Cars & Trucks

1 Answer

Day time runin lights flashin when you start the car and will not stay on also has blown the blubs on dim


the reason your lights flash like that is a warning that you have some problem with the lights.. i had the same problem, if you fix the blown blub it will stop

Jan 12, 2011 | 2001 Chevrolet Cavalier

1 Answer

Had to replace distributor need to set timing,need basic timing degrees? its a 98 dodge dakota 5.2l


Take the number one plug out and put a screw driver in the hole and trun it over by hand till the piston hits the screw driver and then take the screw driver out and trun it just a lil more. Then when you put the distributor in make sure there Is a rotor on it and face the ponit of the rotor to the number one piston and bolte it in and you may have to turn it lift and right to get it right one time. Hope that helps.

Dec 17, 2010 | 1998 Dodge Ram 1500 4WD

1 Answer

My left blinker on the dash stays lit up when headlights r on and blinker doesnt work. what do i do?


sounds like you have a light bulb in backwards. or the filament in a bulb is shorted together, check all turn signal blubs.

Nov 16, 2010 | 1987 Chevrolet Caprice

1 Answer

I need to install the belt back, I am working to install the water pump


Make Sure Your Adjusting is loose and your Belt correcly sitting on the Sleave From the Bottom of the Cranck Pully I See So Many People Re-ajust belt then When Star Engine Belt Broke ...So That Why I insist Sorry For That ... Then check all pully for belt sitting
Slowly Adjust Belt Till it Safe ..Then Turn Engine by Putting A extension Rachet then turn Main Crank Shaft Slowly Complite turn If the belt stay on correcly ..Then Start engine then stop Check again For Belt Position if it Ok ..Your car it fix ... Good Luck

Oct 07, 2010 | 2003 Toyota Camry

1 Answer

2002 XG 350. License plate bulb out. How do I pull bulb, wiring is too tight. Thanks Joe B


2002 HYUNDIA XL 350, LIC. PLATE BLUBS CAN NOT GET ASSEMBLY DOWN TO REPLACE BLUBS, DUE TO THE FACT THE WIRES ARE TOO SHORT TO PULL UNIT DOWN. ANYH IDEAS?

Oct 30, 2009 | 2002 Hyundai XG350

1 Answer

2006 pontiac torrent shut down car will just crank, not start


The factory alarm is not to be tampered with as you can reset it but not disconnect it as it's part of the main fuel injection system. Do you have the right key? Just because it turns and cranks doesn't mean it has the right code. the security light off with the key on ut not cranking? If it stays on you do have a security problem. The system can be reset ( if the battery is good, and hot. Trun the key to crank and letgo the security light will but on or blinking . Leave the key on till the light goes out (around 15 minutes. Once it's out turn the key off then back on and the security light will be back on again. again wait till it goes out turn off then on again till the light goes out. Now turn the key off wait a few seconds trun it on and crank the engine. If it starts then it's reset. Sometimes I've had to do this more than three times to get it to reconize the key as the right one. rember a store cut key won't ever work as it doesnt have the (brain in it the the factory key does. Lets say your wrong, about the security system. The fuel pumps go bad like crazy and its thier season to fail. They fail quicker if you $5 the car alot. (runing on empty) Was the check engine light on as it ran the last time it was running? If so the codes need to be retieved and repaired. A scanner will find the security enabled on too.

Aug 28, 2009 | 2006 Pontiac Torrent

1 Answer

Cruise Control


Most at the time its a brake/cruise control swich located above brake pedal.Its might be shorted or pedal not pushing swich back enough for cruise to work.Anyway the swich is ajustable or replaceable.Ajust it so buton goes about 1/2 of its lengt in.

Nov 17, 2008 | 2000 Ford F250 Super Duty Crew Cabs

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

john h

Level 3 Expert

22569 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...