Question about Geo Cars & Trucks

1 Answer

Finding the tcm on my 97 geo metro lsi - Geo Cars & Trucks

Posted by Jarod ernest on

Ad

1 Answer

Arnie Burke

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Geo Master
  • 6,857 Answers

Autoparts can assist

Posted on Mar 15, 2020

Ad

5 Related Answers

emissionwiz

Marvin

  • 85239 Answers

SOURCE: location of fuses for 97 geo metro

It's either under the dash by your left knee or down on the drivers side kickpanel.

Posted on Dec 05, 2008

Ad
emissionwiz

Marvin

  • 85239 Answers

SOURCE: High-beams not working

U are going to have to replace the mulitfunction switch if the bulbs are not the problem

Posted on Dec 09, 2008

JOHN BOURQUIN

  • 8 Answers

SOURCE: where to fill gear oil in manual 5 speed 1990 geo lsi

It should be the same place as a 1991 Metro, on the back side of the transaxle there is a plug that takes a 15/16 wrench to remove. the plug faces the drivers side tire. If oil drips out when you remove the plug it is full. Otherwise use your finger to see if you can touch the oil. Fill with some type of syringe. jeb

Posted on Jan 23, 2009

Anonymous

  • 21 Answers

SOURCE: install anti rattle clips 97 Geo Metro

Disk brake parts, otherwise known as pad springs. They're on there from the factory. Unless someone was drunk at work again, then the caliper comes off just like changing the pads and the clips go in first, then the pads snap in and caliper goes back on.

Posted on Jul 23, 2009

ZJLimited

ZJ Limited

  • 17970 Answers

SOURCE: Need firing order diagram for 1997 Geo Metro Lsi

1997 Geo Metro 1.3 liter L4 VIN "9"

831ccd3.gif


Hope helps. (remember rated and comment this).

Posted on Sep 10, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

On my 97 geo metro lsi it will not down shift but will shift through gear if you use the gear shift like a manual ans my turn signals stop working when this happened

W age of car..trans has internal issues..will need a fluidpressure test. First chec level n cond of fluid at a partstore free. U cud also hav computer n module problms. Gitta scan also
0helpful
1answer

COMPUTER CUTTING OUT, STOPPING CODES

Should get this checked out professionally before you ruin something.
0helpful
1answer

Egr not working 97 geo metro lsi

H3LL most of those old 90s car it does not work now.
(ive cured many) (some take 5hours hard labor De-carbonizing the thing)

how do you know that,?
guess:
1 P0400 DTC errors?
2 pinging?
3 fails smog?,,.
is it too hard to tell the story>?

This is Suzuki swift if you had not notices
open hood lookup see that sticker, says SUZUKI
clear as day, and means parts more easy to find.
In the USA we got G engines. G10,G13 top sizes
all suzuki's this era
have horrible Rube Goldberg EGR
vacuum and cat backpressure, magic,err horrors
test 1.
find the EGR main,
see rear and the skeleton-ized frame?
hot engine, we use vacuum tool on its nipplefitting
and it stalls the engine or near, 800 goes to 400. rpm.
that means the 5hour labor part is ok.
leaving vacuum parts or electric VSV

if the diaphram fails to move the valve is bad.
if it moves fully (1/4" or more ok.
so remove it, and clean the carbon seen here.
valve ports. put back pass stall test now?
if hot the hidden exhaust path is blocked.

end, im not doing the vacuum/elect, cat pressure side now.. until you report stall test results.
this test here 1 test cuts the job in half.
0helpful
1answer

I have a 1992 geo metro LSI convertable that is missing the triangle shaped trim piece under the driver door mirror.I am told this piece is specific to 1990-1993 geo convertables and no longer available....

they have junkyards for that. there are many people on ebay who will go out and scavenge parts for a price. tough to find a car more then 15 years old though.

search for used geo parts on ebay, find someone who has a lot of them for sale and send him a question about finding you one and how much.

or you can just get your phone book out, find the auto used parts section and call them all until you find someone with an old geo sitting in his yard that you can go look at.
9helpful
1answer

Need firing order diagram for 1997 Geo Metro Lsi 1.3 liter 4 cilinder

1997 Geo Metro 1.3 liter L4 VIN "9"

831ccd3.gif


Hope helps. (remember rated and comment this).
0helpful
1answer

Do the valves need to be adjusted on a 92 geo metro lsi

No. Geo Metros use hydraulic lifters which can not be adjusted. If you Metro is making excessive valve noise, the lifters are probably worn out or the oil level is low.   
3helpful
1answer

Where to fill gear oil in manual 5 speed 1990 geo lsi

It should be the same place as a 1991 Metro, on the back side of the transaxle there is a plug that takes a 15/16 wrench to remove. the plug faces the drivers side tire. If oil drips out when you remove the plug it is full. Otherwise use your finger to see if you can touch the oil. Fill with some type of syringe. jeb
Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

46 views

Ask a Question

Usually answered in minutes!

Top Geo Experts

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6928 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14944 Answers

Greg Bernett
Greg Bernett

Level 3 Expert

2993 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...