Question about Chevrolet Cars & Trucks

Open Question

How to install rpm sensor of chevrolet cuze? - Chevrolet Cars & Trucks

Posted by AQUILINO RIVERA on

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 corvette running too rich black smoke and coughing low rpm


the brake servo needs refitting and ensuring correct torque

Jun 11, 2013 | 1994 Chevrolet Corvette

1 Answer

What is the ohms that my mass airfflow sensor is to be at?


there is no ohms chart for your car in order to test the sensor you need a scanner and with a scanner you read the MASS voltage at differant RPM's.or in grams of air per second for example 1000 RPM = 23 grams, 2000 RPM = 32 grams and so on at idl the voltage should be around 0.2 volts and very up to 5 volts as the RPM incresses.

Aug 28, 2011 | 1999 Chevrolet Lumina

1 Answer

How to fix p1345 obd code on 97 chevy 1500 5.7 Lt.


P1345 is "Crankshaft position sensor / Camshaft position sensor correlation"

Code P1345 determines if the distributor is installed incorrectly, or if a mechanical malfunction is present in the engine. The light will trigger when the engine is running and the camshaft sensor reference pulse is not detected at a correct relative position with the crankshaft pulse. Most likely causes for this Chevy check engine light code include a faulty crankshaft position sensor, a wiring concern or an improperly installed distributor. A quick check on the crankshaft sensor is to monitor the RPM value with a scan tool while revving up the engine. If the reading is close to twice the expected RPM, then the sensor is likely faulty. There are other less likely concerns possible, such as base engine or computer related issues, but these involve more in depth testing. I hope this information is useful.

May 27, 2011 | 1997 Chevrolet K1500

1 Answer

Where is the crankshaft position/crank angle sensor located on a 2005 kia sedona


Hi, at the front of the crankshaft. if its near time for the timing belt, you want to replace it along with any pullies, tensioner and water pump


The crankshaft position sensor is mounted on the engine near the crankshaft.

Operation

The crankshaft position sensor is a Hall-Effect sensor that senses the crank angle (piston position) of each cylinder and converts it into a pulse signal. The signal from the sensor is relayed to the ECM to indicate engine rpm and the position of the crankshaft.

Removal & Installation

  1. Disconnect the negative battery cable.
  2. Disconnect the connector from the sensor.
  3. Remove the bolt that retains the sensor in place.
  4. Remove the sensor from its mounting. To install:
    1. Installation is the reverse of the removal procedure.
    2. Clearance between the sensor and the sensor wheel should be 0.020-0.059 inch. 2002-2005
      1. Properly connect the scan tool.
      2. Start the engine and allow it to idle.
      3. Be sure the idle position switch is ON.
      4. Specifications are as follows:

        Temperature - 4°F, test specification 1500-1700 RPM Temperature 32°F, test specification 1350-1550 RPM Temperature 68°F, test specification 1200-1400 RPMTemperature 104°F, test specification 1000-1200 RPM Temperature 176°F, test specification 650-850 RPM

Mar 16, 2011 | 2003 Kia Sedona

2 Answers

Power at engine module and power to good coil packs but no spark


Sounds like a bad crank sensor or a bad ignition module. If you have a scanner that can read sensor data, you can crank the engine over and see if there is an "RPM" reading. If there is an RPM reading, then the crank sensor is good...Throw the module away. If there is no RPM, replace the crank sensor.

Jan 11, 2011 | 1998 Chevrolet Cavalier

1 Answer

2004 Trailblazer is hard to to steer when the RPM's of the vehicle drop to idle speed. It acts like it doesn't have power steering but if you raise the RPM's it's fine. Supposedly had a new pump installed...


There is a sensor in the hydralic steering line that tells the PCM to raise the engine RPMs when power is called for when idling. Check to see if the wire connector is attached, if so you may need to have the sensor replaced.

Jan 07, 2011 | Chevrolet TrailBlazer EXT Cars & Trucks

2 Answers

Replaced crank shaft position sensor from autozone. erased all codes. still showing code p1345. ive been told to use acdelco. am i doing something wrong?


Code p1345 is the crankshaft variation learn.You need to get the crankshaft variation learn done for the code to clear.You will need a scan tool.This should take care of the check engine light.Hope this helps.Good luck.

Mar 16, 2010 | 1996 Chevrolet C1500

1 Answer

Engine RPM is 1800 with gas peddle almost to the


Ck or replace your MAF sensor. First sensor in the duct coming out of air filter. It controls the air/fuel ration

Jun 14, 2009 | 2000 Chevrolet Silverado

1 Answer

Error code po113


the error P0113 still comes up even after a new sensor was installed and the transmission shifts very hard. Found a break in one of the wires to the sensor. Soldered it back to gether. Found that the engine has a limit to the rpm when rev-ing in neutral.
Thanks
rkbids

Aug 05, 2008 | 2002 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

john h

Level 3 Expert

23504 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...