Question about 1996 Jeep Grand Cherokee

2 Answers

1996 Jeep Grand Cherokee No Start

Vehicle crank but no start /No Gauges
No crank signal/ no spark -- replaced coil/ crank sensor.
No Injector pulse signal at injector -- have cam sensor output signal.
Scan tool no communication -- all fuses good/ power and grounds to DLC good
Tried manual scan (key on, off sequence) -- no lights flash
Tried unplugging sensors(cam/ crank/ coolant temp/ Coil/ ABS/ Trottle Position/ MAP/ IAC/ a/c Pressure/ Ambiant air Temp/ Injectors -- Gauges did not return.
Replaced -- Plugs/ Wires/ Cap/ Rotor/ Pickup(cam sesor under distributor)/ Coil/ Crank Sensor

Please Help starting to get pricy

Posted by SupR_Tune on

Ad

2 Answers

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 2 Answers

I would be thinking that there is a good chance that you need to be checking out replacing the computer, if you aren't getting any communication with the proper scan tool then the computer isn't communicating with anything in the vehicle...... I would have guessed first off that the ignition control module might be bad but that is obviously part of the computer also, I would be looking in that direction.

Posted on Sep 19, 2009

Ad

april

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

I have a 1996 jeep grand cherokee and im not getting spark to the plugs.i replaced the crankshaft sensor and ignition coil already and still having problem.if i replace the camshaft sensor would that fix the problem ??? Or what should i do ???

Posted on Jul 23, 2012

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 Jeep Grand Cherokee Laredo 4.8l V8 Camshaft Position Sensor Replacement. How can I tell if mine had a spacer on the mounting bolt.


I looked at info for 4.7L engine. I would have checked the cam sensor wiring circuits, before replacing anything. Three wire connector, ref voltage--ground--signal.
Some of these vehicles, the computer needs to see both the cam and crank sensor signals or it won't start.
Engine cranking do you have spark at the plugs--proper fuel pressure--fuel injector pulse?
I don't think I have ever seen a spacer on the sensor mounting bolt, but, I haven't seen everything.

Feb 18, 2018 | Jeep Cars & Trucks

2 Answers

1996 jeep grand Cherokee will turn over but not start. weak spark. fuel at fuel rail. replaced PCM 1 month ago. replaced crank shaft sensor 3 months ago....


See if your getting spark at the ign. coil first (passengers side on that year) if you are change the crank shaft sensor making sure you mount it as close to the engine as possible so it never gives you trouble again.

Aug 20, 2013 | 1996 Jeep Grand Cherokee

1 Answer

I have a 1996 grand cherokee. engine cranks but wont start. getting nothing on dashboard gauges and getting nothing but dashes on overhead digital gauges except temp. recently had new alternator put on. is...


More than likely needs a crank sensor, Try cranking with the crank sensor disconnected, you should not get the dashes in the cluster. The crank sensors take out the communication system of the vehicle

Jul 20, 2010 | 1995 Jeep Grand Cherokee

2 Answers

Grand cherokee 2000 starting probs


you need to see if you have spark and check all fuses and see if you have fuel pressure and injector pulse if no spark and no injector pulse suspect crank sensor or ignition control module if no fuel pressure check fuses then relays and then suspect pump

Aug 18, 2009 | 2000 Jeep Grand Cherokee

3 Answers

1996 jeep grand chrokee turns over will not start, replaced cam shaft censor and ECM, and coil. distibuter cap looks bad has some white dust inside and contacts burnt. could it be that?


If you did not replace the CRANK sensor on the back side of the motor this most likely is the problem and a very common one at that.this controls spark and injector pulse,unlike the cam sensor which just shows when #1 cilyder is up.

Jul 03, 2009 | 1996 Jeep Grand Cherokee

2 Answers

96 grand cherokee crank no start, no spark from


have the crank sensor replaced this controls the spark and injector pulse it is located on the drivers back side of the engine above the transmission housing!

Jun 08, 2009 | 1997 Jeep Grand Cherokee

1 Answer

Engine wont start seems to be a fuel injector problem ,not fuel pump,has fire to coil and plugs.5.2 v-8


It is the VATS system (vehicle anti theft system). The codes need to be cleared out and lock and unlock the drivers door from the outside with the key. This is most likley the problem if the injectors are not geting pulse or check the crank sensor with a scan tool in datastream, it will show RPMs if it is getting crank signal.

Apr 04, 2009 | 1994 Jeep Grand Cherokee

1 Answer

Car has no spark or injector pulse(new ecm,crank sensor)


Check the fuse for the injectors, some vehicles have the injectors and coil running on the same circut, at the same time check the fuse for the ignition.

Jan 30, 2009 | 1996 Dodge Avenger

Not finding what you are looking for?
1996 Jeep Grand Cherokee Logo

1,006 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14850 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...