Question about Daihatsu Cars & Trucks

1 Answer

Cylinder head bolt torque specs, Daihatsu Mira

What are the torque settings for Daihatsu Mira cylinder head bolt settings FK engine @

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

  • Daihatsu Master
  • 60,902 Answers
Ad

6 Suggested Answers

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 98 Answers

SOURCE: how to rebuilt the cylinder head of daihatsu charade 3 cylinder engine

Which motor?

Posted on Sep 04, 2008

SOURCE: need to know cylinder head bolt torque specs

Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Posted on Feb 07, 2009

Anonymous

  • 1 Answer

SOURCE: Angle Torque settings head bolts

Use new bolts, tighten in the following stages 1. 20Nm 2. 100Nm 3. wait 3 mins 4. slacken bolts 1&2 retighten to 20Nm +110 degrees 5. carry out stage 4 for bolts 3,4,5 & 6 then bolts 7,8,9 &10 Sequence, 8 4 1 5 9 7 3 2 6 10 Bolts 9 & 10 are flywheel side of the engine.

Posted on Mar 17, 2009

Anonymous

  • 8 Answers

SOURCE: need cylinder head bolts torque settings for nissan 3.2d

what nissan model do you need the head torques for

Posted on May 01, 2009

inspectmycar

Chris Biddle

  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is torque settings for head bolts on Kia pregio 2001


What are the cylinder head torque settings for a KIA K2700

www.answers.com > ... > Categories > Cars & Vehicles > Asian Cars > Kia
What is the torque specification for the cylinder head on a 2002 Kia Sportage? ... the correct torque for cylinder head bolt of kia pregio 2.7 diesel is 130-135ft-lbs. ... Thehead bolt torque settings, on your Kia 2.7 diesel engine, is 70 pounds per ...

Aug 17, 2015 | Kia Cars & Trucks

2 Answers

What is the cylinder head bolt torque settings fir a 4g69 mitsubishi engine ?


BOLT INSTALLATION


Apply engine oil to the thread of the bolts and to the washers.
Tighten the bolts to the specified torque, using the tightening sequence shown.
Tightening torque: 54 ft-lb +/- 2 ft-lb
Loosen all bolts fully in the reverse order of tightening.
Re-tighten the loosened bolts to the specified torque in the tightening sequence shown.
Tightening torque: 15 ft-lb +/- 1 ft-lb
This step is to make it easier to ensure you are making 90 degree turns. Make a paint mark across each bolt head and cylinder head.
Tighten the cylinder head bolts 90 degrees in the specified order.
Tighten the bolts another 90 degrees in the specified order and check that the paint marks on the cylinder head bolts are aligned with the paint marks on the cylinder head.
Link to the guide for this engine: http://www.mivec.co.nz/tech/4G9x_Engine_Manual.pdf



Aug 04, 2014 | 2007 Mitsubishi Outlander 2.4

1 Answer

Daihatsu g200 engine head torque settings when replacicg head gasket


not many of these around nowdays ,65lbs for the head bolts

Apr 06, 2011 | 1992 Daihatsu Charade

1 Answer

Correct pressure for torque the head of mazda pickup 1998


Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.


Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.



B2500 4 Cylinder

Torque sequence: --------- ' 10 6 2 4 8 ' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51 Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final tighten all bolts an additional 90 to 100 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.







B3000 3.0 6 Cylinder

Torque sequence ---------- ' 6 4 2 8 ' ' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque to 73 Ft/Lbs









B4000 4.0 6 Cylinder

Torque sequence --------- ' 5 1 3 7 ' ' ' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs Step 3: turn cylinder head bolts in sequence an additional 90-degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.


Good luck with this job!

Feb 06, 2011 | 1998 Mazda Pickup

2 Answers

Torque setting cylinder head bolt 4 cylinder KIA sportage


I need the torque settings and pattern for a Kia Sportage 2.2

Nov 24, 2009 | 2001 Kia Sportage

2 Answers

1994 Daihatsu Mira L200 repair Manual


how to overhaul mira l2 gear box??

Apr 17, 2009 | 1992 Daihatsu Charade

2 Answers

Need to know cylinder head bolt torque specs


Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daihatsu Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Daihatsu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...