Question about GMC Cars & Trucks

Open Question

I kooke the cable up backward on my 16 black widow gmc now it wont start

Posted by Ashlie Lichtenwalner on

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On a 2002 4Runner a connector is not working


Starter good, battery good, still wont start... - YotaTech Forums

www.yotatech.com/f2/starter-good-battery-good-still-wont-start-251448/
Mar 26, 2012 - 96 4runner V6 4wd wont start... first I had the battery checked, it was fine. then I ... 95.5-2004 Tacomas & 96-2002 4Runners 4th gen pickups and 3rd gen 4Runners ... Just had this problem with my 94... turned out 2 wires going to the back of ..... I have 12V at my starter connector and main cable from battery. 4Runner cranks but won't start
Feb 24, 2013
Fuel injectors & CSI not firing, crank only / no start
Mar 25, 2012
4runner fuel pump electrical problems
Mar 16, 2011
No Start Condition: Ignition and Coil Test Info for 3VZE (89-95 ...
May 10, 2003
More results from www.yotatech.com

How To Replace A Toyota 4runner Starter Relay - Made Man

www.mademan.com/mm/how-replace-toyota-4runner-starter-relay.html
Sep 21, 2010 - To replace a Yoyota 4Runner Starter Relay you will need: ... As with any electrical procedure on a car or truck it is best to remove the negative battery cable of the Toyota 4Runner to prevent any electric shocks when working on it. ... If it does not start straight away, rock the car backwards and forwards with ...

please help. 94 4runner wont start. not starter or battery - Car ...


Jan 08, 2016 | Cars & Trucks

2 Answers

2003 Pontiac sunfire wont turn over new battery dash lighs up


Pontiac Sunfire Questions - car won't start - CarGurus

www.cargurus.com > Questions > Pontiac > Sunfir

CarGurusAug 16, 2011 - car won't start - replaced ignition lock on 2002 pontiac sunfire antitheft light is ... system goes into fail safe mode and you won't have any more problems. ...lock cylinder on 2003 pontiac sunfire....when new lock cylinder was ...

Sep 10, 2015 | Pontiac Cars & Trucks

2 Answers

What do i do after installing starter and still no start but al other elec works and battery good? Could I have put wires to starter on backwards? 1994 GMC Suburban 1500.


generally the cables to the starter posts and the lengths of the wires help you put them on correctly, so i doubt that is the issue. why did you replace starter in the first place? what were the symptoms exactly?

Aug 04, 2015 | GMC Cars & Trucks

1 Answer

I have a 2000 gmc w3500 gas motor that has spark and fuel in the fuel bar but wont start,,and even if i put ether in the intake it won't start


How is fuel pressure? He must try to start with ether, If you turn crank by hand forward and backward you feel how much play in timing chain?

May 04, 2014 | 2001 GMC W3500

1 Answer

Why wont my yukon start after replacing gas pump and filter


If you replaced the fuel pump, you may have a line reversed or the fuel filter is backwards. Check for kinks. Make sure the new pump is working too. Sometimes it is possible to get a bad part.

Feb 05, 2013 | GMC Yukon Denali Cars & Trucks

1 Answer

Put batt. in backwards by accident, replaced alt. and alt. hot wire as they were burnt up. but wont start, motor turns over but wont crank. could it have burnt up solenoid


check ignition module, you may have fried it, if motor turns over the solenoid is o.k. -- your probably not getting any fire to the plugs, check to see if you are getting any spark at plugs

Jan 08, 2012 | 1989 GMC Sierra

1 Answer

Car alarm installed. Car wont start.


im sure you cut the starter wire in the ignition switch. usually white. put it back and check. if it starts check the programming configuration of the black widow

Jun 03, 2009 | 1995 Jeep Grand Cherokee

2 Answers

Remove battery from 99 yukon


your gonna need either a 5/16 or 8mm wrench.  loosen the negative battery cable (black cable) off first and move it to the side where it wont touch the battery or anything metal.  then loosen and take off the positive (red) cable off and then just loosen the battery hold down bolt and the battery should left out. just like a top post battery make sure you dont touch anything metal with the wrench while loosing the bolts.

Feb 24, 2009 | 2008 GMC Yukon

1 Answer

98 sentra not starting.


check fuses under the hood main fuse

Jan 24, 2009 | 1998 Nissan Sentra

1 Answer

Gmc jimmy wont start but battery seems fine


sounds like the side post terminals are not tight enough check them by putting a 5/16 inch wrench on the bolts and tightening them up.

Jun 28, 2008 | 1996 GMC Jimmy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Ryan Lutton
Ryan Lutton

Level 3 Expert

1255 Answers

john h

Level 3 Expert

23504 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...