There are only 2 places that you have the problem on the inside door handle. one is at the handle,and the little plastic holder that holds the rod to the handle broke, or the plastic clip the the door lock mechanism broke. the first can be removed without taking the door apart. the inside door handle has a screw holding it in place. you can remove the handle and see if its broken. the second requires you to remove the door panel, to replace the clip that hold the rod to the lock. I door handle in the car is a dealer item only(sorry to tell you that), the clip for the lock, you can get at the auto parts store. hope this helps

Jan 11, 2011 | 1991 Acura Integra Hatchback

1 Answer

Door lock assembly

Toyota Corolla 1988-1997 Repair Guide Door Locks - REMOVAL & INSTALLATION
(see Figure 1)

Disconnect the negative battery cable.
Remove the door panel and watershield. Remove the service hole cover.
Disconnect the door outside opening linkage. Remove the two mounting bolts and remove the door handle if in need of replacement.

Fig. 1: Power door lock control system component locations

Disconnect the lock cylinder control linkage.
Remove the lock knob and the child protector lock lever knob.
Remove the lock assembly retaining screws and remove the door lock. If equipped with power locks, disconnect the electrical harness.
To remove the lock cylinder, remove the lock cylinder retaining clip and pull the cylinder from the door.

To install:

Coat all the door lock sliding surfaces with multi-purpose grease.
Install the outside handle with the two retaining bolts, if removed.
Install the door lock solenoid linkage to the door lock.
Connect the link to the outside handle.
Install the lock knob and the child protector lock lever knob.
Install the door opening control link tighten the mounting bolts to 48 inch lbs. (5 Nm).
Install the door lock cylinder control linkage.
Install the door panel and watershield.
Reconnect the negative battery cable.

Hope help with this; remember rated this post and thank you for using Fixya.

May 20, 2010 | 1991 Toyota Corolla

2 Answers

91 4runner power window fuse s are good but none of the door windows work and only the passenger power door lock works

replace the power window master switch and chances are the lock actuators are bad. replace as neccessary. happy holidays

Dec 28, 2009 | 1991 Toyota 4Runner

1 Answer

1991 toyota camry

double check the fuses, etc first to see if anything blew. there should be circut breakers to check as well (consult your manual). have someone look at your wiring to make sure it hasn't corroded inside the doors.

Jun 12, 2009 | 1991 Toyota Camry

1 Answer

1991 Toyota electrical issues with alarm system and battery, dead car sometimes and dash lights at others. Now won't start at all. Door locks lock at odd times by themselves.

disable or remove the alarm and see if problem gone especially ifits an aftermarket fitment alarm system.sounds like this job is one for an auto elec.
have had central door lock modules cause this

May 30, 2009 | 1991 Toyota Camry

2 Answers

Sliding passenger door will not unlock/ open

I assume you mean a 1991 Previa (that was the first year of the model). It is likely you have broken a small spring inside the door that connects the handle to the latch. The only way to tell is to remove the inner door panel (two screws: one under the door handle and one midway along the upper part of the interior door structure then pull out and up).

Apr 04, 2009 | 1991 Toyota Previa

1 Answer

1991 Toyota Camry DX - Front Passenger Door Lock won't disengage

Your power door locke solenoid is seized. You will need to replace it. You are going to have to get the entire door panel off, and then reach in to manually pull the solenoid arm to retract the lock mechanism. Then the door will open.

Mar 06, 2009 | 1991 Toyota Camry

1 Answer

I replaced the outside door handle plate and after I was done the door locks with the remote and with the key on the paseenger door but not the driver's door. What did I forget to do?

you forgot to hook the manual lock rod into its proper plastic clip for the driver's door lock assembly. An easy fix but you'll have to go back inside the door again.

Feb 17, 2009 | 1991 Toyota Camry

2 Answers

In my 1991 toyota camry, both, the power locks and windows stopped working. I can't seem to locate their fuses

There is no fuse. The circuit is controlled by a circuit breaker, and they never fail. What I would be looking for, from personal experience, would be a broken wire between the door and the body. The wires break inside the harness, right between the body and the door.

Dec 18, 2008 | 1995 Toyota Camry

Not finding what you are looking for?

View Most Popular

Cars & Trucks

Need to wire the driver side door lock switch

1990 Toyota Camry

Open Questions:

0 Answers

Ask a Question

Usually answered in minutes!

1991 pickup. How can I replace door lock holder?

Add Your Answer

Attachments: Added items

Related Questions:

Need to wire the driver side door lock switch