Question about Cars & Trucks

1 Answer

How. Do you install auto saver 88 fog lights kit

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 30,888 Answers

Videos and text-based help in general terms. As expressed, fog light kits don't come with instructions as too many variables.

https://www.google.com/search?q=install+auto+saver+88+fog+lights+kit

Posted on Feb 05, 2020

Ad

3 Suggested Answers

brainyass

Brainyass Rabbit

  • 242 Answers

SOURCE: 1996 jeep cherokee sport.

If it's a lighted switch, you should have 3 terminal connections on it. One for the "ignition on" wire (from your fuse box). One going to the fog lights to turn them on when you flip the switch and one ground for the switch light to work. If your switch doesn't light, you should only have 2 terminal connections (no ground).

Find an "ignition on" plug on your fuse panel. It is only hot when you turn your ignition to the on position (not crank position). With your keys out, it should not have any power to it. Hook your "hot" wire from fuse panel to switch, take your keys out of the ignition first to be safe. Now hook the other wire from the switch to the "hot" on your fog lights. You will have to find a pass through rubber grommet on your firewall to go through. Use a clothes hanger to help fish it through. Now ground your fog lights to a grounding screw somewhere in the engine bay. There should be a few you can use, possibly one of the bolts that hold the front shroud on. Make sure it's a metal surface and use sandpaper to scrape off paint to get a metal to metal contact. Cover area with petrolium jelly to ward off rust. If your switch is lighted, hook to ground wire on fuse panel. Test with ignition on. If it doesn't come on, check your grounds again.

Posted on Oct 16, 2008

Ad

Anonymous

  • 203 Answers

SOURCE: How can install fog light on chevy cavalier 2002

is there 2 blanks on the bumper that need to be cut out. did you get instructions.

Posted on Nov 22, 2008

phatboy29

  • 117 Answers

SOURCE: looking for fuse for fog

Check your instructions with the fog lamps, I believe you will need to take your car to a dealer to have them activate the fog lamp driver in the Totally Integrated Power Module.

Posted on Jan 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Red wire broke off connector on left front fog light on Oldsmobile 88


Hi, there is 2 things you can do, like Ted sad it just a light, so you can just go 2 any auto store explained what happened and just get an extention wire 4 Yr red1 with connections and isolation that you can just connect 2 Yr broken wire and clamp it with just plyers with out any soldering tools. Or get any similar wire and just tire up 2 Yr broken wire with the plyers and use some electrical tape over it so it doesn't short with the ground. That's all. G/luck.

Dec 08, 2013 | 1997 Oldsmobile 88

1 Answer

Signal lights dont work and want to know where the fog light switch is at


With the switch in sidelight or dip

position, pull the switch to its first

position to turn on the front fog lights.

Pushing the switch in or turning it to OFF
or AUTO will turn off the front fog lights (this is for the front)


With the switch in any position except

OFF or AUTO, pull the switch to its

second position to turn on the rear fog

lights. This will also turn on the front fog

lights unless main beam is selected.

Pushing the switch in or turning it to OFF
or AUTO will turn off the rear fog lights (this is for the rear)

Exterior lighting

Exterior lighting switch

A. OFF.

B. Side (parking) lights.

C. Headlights.

D. Auto.

E. Front fog lights.
F. Rear fog lights.

It is the round knob nest to the steering colume

Aug 18, 2011 | 2003 Jaguar X-Type

1 Answer

Looking for fuse for fog lights on a 2008 dodge charger. we installed a fog light kit. the car is pre-wired for them. we replaced the head light switch with the one from the kit. fog lights arent...


Check your instructions with the fog lamps, I believe you will need to take your car to a dealer to have them activate the fog lamp driver in the Totally Integrated Power Module.

Jan 23, 2011 | 2008 Dodge Charger

1 Answer

How to install original factory fog lightson ford escpae xls 2010 I purchase the original fog lights butcanot find the harness or connectors. Do I need to purchase another harness?


hi when you purchased these they should have come with a wiring kit supplied, if not then you will have to go to ford and ask them for the wiring kit for them, on most replacement fog lights not ford made come complete with wiring included...hope this helps

Aug 01, 2010 | 2008 Ford Escape

2 Answers

How do you change the headlight bulb on 1996 olds delta 88? I cannot get to the bulb assembly.



REMOVAL & INSTALLATION

See Figures 1, 2, 3 and 4
  1. Disconnect the negative battery cable.
  2. Remove the fog lamp-to-bumper assembly retaining screws. Be careful not to disturb the adjusting screw.



0900c152800b1fa2.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Unfasten the 2 Torx® fog light retaining screws (1), making sure not to disturb the adjusting screw (2)
  1. Squeeze the bulb and socket assembly retaining clip prongs inward, and pull the bulb and socket from the rear of the fog lamp.



0900c152800b1fa3.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Squeeze the bulb and socket retaining clip prongs inward ...


0900c152800b1fa4.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: ... then pull the bulb from the rear of the fog lamp
  1. Unplug the fog lamp electrical connector.



0900c152800b1fa5.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 4: Unfasten the fog lamp electrical connector
  1. Install the assembly, retaining bolts and connect the negative battery cable.


AIMING

  1. Park the car on a level surface, at least 25 ft. (7.6m) from a wall that is perpendicular to the ground surface. Make sure there is no excess weight in the trunk, unless you normally travel with that amount of weight in the car. Bounce the car a few times to settle the suspension.
  2. Measure and record the distance from the ground to the center of each fog light lens.
  3. Turn the fog lights on and adjust so the hot-spots (lit area of most concentrated intensity) are 4 in. (10cm) below the height of the lenses. The ADJUSTING screw is located at the top right corner of the fog light.

Jan 25, 2010 | 1996 Oldsmobile 88

2 Answers

My car( neon 97) didnt have fog lights originaly and i dont know how to instal it


its not a bad job on a neon ,the fog light kit you will buy will come with a switch and the relay and wiring for installing them,they also came with a real good set of directions for doing this,if you need to get someone to help you with doing this,sometimes running the wires is tricky,but other than that the fog lights can be mounted in the same place as the originals was,and they look good,i sold my 97 neon and i had fog lights on it,they were after market but looked and worked excellent,with a little work and time anyone can install a set on any car,good luck.

Jul 25, 2009 | 1997 Plymouth Neon

1 Answer

Lights


FROM: Lusty Kid:

Your fog lights should not work with high beam... they should work with the low beams. they are connected wrong, which probably drew too much current through the light switch burning out the contact points for the parking lights in the switch

Start by Fixing the fog light connections to work with low beams. Appears to me this was not factory installed. Aftermarket kit maybe! Then see if your parking lights work. If parking lights don't work still and everything else works, replace the light switch $50 at the dealer. The switch works the fog lamps when you pull out the knob to turn on the fog lamps when the lights are turned on. When the fogs are on you will see a little amber light to let you know your fogs are on. When you switch to high beam the fog lamps go off. Again if its not working that way, then is wired wrong. Needless to say, there should be connectors in the harness of the lights for the fog lamps. Use those if possible with the kit that you can get at the dealer, or you can splice the connector with those blue splicing clips sold at the auto part store. Make sure ground is ground when splicing and water proof the connection sith silicone and tape.

Dec 13, 2008 | 2004 Ford F150

1 Answer

How can install fog light on chevy cavalier 2002


is there 2 blanks on the bumper that need to be cut out. did you get instructions.

Nov 22, 2008 | 2005 Chevrolet Cavalier

1 Answer

Replacement of Fog light for BMW 1997


Answer is on Bavarian Auto web site:
3 Series 92 to 98 Fog Light Replacement-
To install a fog light, insert a flat blade screwdriver through the front bumper grill and release the fog light retaining clip. Remove the fog light and disconnect the wiring harness. Installation is the reverse of removal.

http://www.bavauto.com/shop.asp#e36fog

Sep 01, 2008 | 1998 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

john h

Level 3 Expert

22486 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...