Question about Jeep Cars & Trucks

Open Question

Will throwing the code B0006 Cause a 1996 Jeep Grand Cherokee not to start

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 41 Answers

SOURCE: engine code 95 jeep grand cherokee lerado

12 is a battery disconnect within the last 50 start cycles and 55 means the end of the diagnostic cycle.  Basically the computer found nothing wrong. The 12 code may seem incorrect if you haven't disconnected the battery recently, but from my experience the 12 code shows up almost all the time regardless.

Posted on Dec 16, 2008

Ad
motor1258

Mike Butler

  • 6674 Answers

SOURCE: heated seat 1996 jeep grand cherokee

C1 & C2 in your panel are most likely one of the culprits, if no power at heater at seat. Sounds like testing for power at seat switch is easier to do than get at these circuit breakers in the panel. If you have power at switch at seat, then it's not the fuse/circuit breaker. Good reading at this link for you.


http://www.wjjeeps.com/seats/seats.htm#HEATED

Posted on Dec 29, 2008

Anonymous

  • 55 Answers

SOURCE: serpintine belt

This link will take you to a picture of the diagram. If the link doesn't work contact me and I can email you the picture directly.

http://autorepair.about.com/library/illustrations/bl506a-lib.htm

Posted on Jan 10, 2009

Patrick Miller

  • 154 Answers

SOURCE: LOCATION OF LIGHTER FUSE FOR 1996 JEEP GRAND

If you have the owner's manual look up fuses in the index, good illustration. If you don't, I do. It shows a relay and a 15 amp fuse. Look at the passenger kick panel, pull the cover, and it is #2 fuse (second from the top on the left) The see the relay you may have to pull the panel (two screws and a clip) the relay is the third cavity down, third row from the firewal side.
Let me know if this works for you?

Posted on Apr 03, 2009

EnginEar

EnginEar

  • 57 Answers

SOURCE: 2001 Jeep Grand Cherokee. Malfunction light came on. What is the cause?

You can do one of three things.1. buy a scan tool 2. go to a dealer and pay to have the codes read and diagnosed 3. go to your local parts chain to have it read for free. (call first to verify). The code will tell you what system is malfunctioning and what the malfunction is. The parts store option is my choice, because you can also get the part to fix it if needed and you are not out the $ for diagnostics, nor did you need an appt to get it in.

Posted on Apr 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is it safe to leave thermostat off on 1996 jeep grand cherokee


it won't cause damage but the engine will never get to a high enough operating temperature which won't be good for fuel econommy and may throw up a few codes ie o2 sensors not hot enough , i would'nt leave it out , why do you want to ?

Jul 29, 2014 | Cars & Trucks

1 Answer

What is the abs code 23 valve feed failure for a 1996 jeep grand cherokee


Need to start with intake air sensor , voltage problem .
check p codes 112,113 ,1291 they are aftermarket codes for your code 23 9d57c844-7124-4940-83c9-28a86a03e49d.jpg

Apr 09, 2014 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Can only start jeep when gas pedal is to the floor


If it's not throwing any codes its probley clog injectiors

Jul 31, 2013 | 1996 Jeep Grand Cherokee

1 Answer

What would cause my 96 Jeep Grand Cherokee 4.0 to Quit


Most times the symptoms you have are the beginning stages of either a fuel pump failure, crank position sensor or a bad ignition switch. Unless you catch it at the right time though, it will be difficult to diagnose (this is the part that shops hate the most...when testing will show everything is good but everyone knows its not.)
Hopefully it may have set a stored code which will make that easier.

Oct 17, 2009 | 1996 Jeep Grand Cherokee

1 Answer

96 Jeep Cherokee Sport Hard Starting


The Engine coolant temp sensor would ABSOLUTELY cause a hard start, but don't guess get the codes check again at Auto_Zone to make sure. Another cause of that kind of hard start is a dirty throttle body/ intake manifold. Use INTAKE cleaner and a rag clean the intake esp[eciall in the throttle body area. Good Luck

Dec 28, 2008 | 1996 Jeep Grand Cherokee

3 Answers

1996 Jeep Grand Cherokee - Will Not Start or Run


they have crankshaft sencers on the transmission on jeeps. it would be up high on the drivers side on front of transmission. they will cause it to not get fuel or fire and can run then quit.

Jul 19, 2008 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...