Question about 2007 Nissan Quest

Open Question

07 nissan quest side door won't pull open. The metal wire that I guess pulls it in just hangs down from the side when I manually open the side door. Any suggestions?

Posted by Raymond Accordino on

Ad

5 Related Answers

Anonymous

  • 1 Answer

SOURCE: 2004 Nissan Murano, back door can't open

I had a similar problem with a sienna and sometimes the cable ( inside the door) between the handle and the latch gets stuck in the sleeve. Kind of like the brake cable on a bike.
take the panel off by removing all the screws you can see on the panel and pull the panel off. There will be plastic pins holding it. Some of them may pop off and some will break off.
Drip oil down the sleeve so the cable slides freely. I used bike chain oil. Do not use WD40. This is **** and will not work for very long. Try the handles a few times before you put the panel back.

Posted on Mar 03, 2009

Ad

Anonymous

  • 147 Answers

SOURCE: power window problems!!!!! window stuck down and it looks like

use the switch from the other side connect just use it and unplug it..it the switch does not work go to motor

Posted on May 08, 2009

Ad

Anonymous

  • 1 Answer

SOURCE: VW Beetle door won't open

2002 VW Beetle doors wont open from outside after changing battery

Posted on Nov 06, 2009

ricebike

  • 42 Answers

SOURCE: I have also broke off my 2001 Nissan Quest sliding

the child lock rod may have been extended...
open the driver side door, and with a skinny finger, push that child lock rod back in towards the rear of the sliding door
use the passenger side as reference
once you pushed it in, you can now open it from the inside handle

Posted on Jun 17, 2010

foster

  • 2 Answers

SOURCE: 2007 Kia Spectra Manual Door Latch

Well you must take off the inside of your door, the door panel. look for the screw holes and unscrew it.

Posted on Jun 24, 2012

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Nissan Quest 1999 Van - rear wiper seems to be running even if there is no key in the ignition and drains the battery, pulled RR Wiper fuse 10 Amp and it did not help. When the key was inserted into rear...


If you pulled the correct fuse for the rear wiper (Under the Dash) (or under the hood?) sometimes there are 2 fuses. But if you pulled the correct fuse and you still have power going to the wiper, I would pull the fuse on either side of the wiper fuse socket. With the wiper fuse socket empty, pull the fuse on the left or right one at a time, check for power at the wiper motor each time a fuse is pulled. When you find the power source then you'll need to trace your wiring where the wipers and say for example the dome light meet. I can almost bet the wires have rubbed or something like that and are feeding power to each other. Maybe a melted wire or like what I found on my sons car was that the back side of the fuse block had melted from him running all those high power stereos. He melted the block and the connection melted together. Hope this helps.

Jan 16, 2013 | 1999 Nissan Quest

1 Answer

Part of the driver side outside door handle for my 1999 Nissan Quest broke and it is still attached but will not allow me to open the driver door from the outside. Nissan no longer makes this part and I...


you need to remove door trim panel for access. Ford has one but you will have to paint it. buy a psray can of paint at an auto astore. paint code on your driver door opening sticker.
quest & villager are same van, built at same plant by Ford, Nissan powertrain.

Go to our site and read files. everything about villfewr quest. 3000 members. I was Ford manager of service issues on this van. I can get you part number and you can order from tascafordparts.com at discount. I also have shop manual & wiring book for sale $20. Let me know.

http://groups.yahoo.com/group/villagerquest/

Dec 13, 2010 | 1999 Nissan Quest

1 Answer

Programming garage door opener in the visor of the 1999 nissan quest


here is a link to the owners manual for a 1999 nissan quest. The instructions for programming a garage door are on page 2-27. Copy and paste the link in your address bar. I hope it helps.


http://www.nissan-techinfo.com/refgh0v/og/quest/1999-nissan-quest.pdf

Oct 08, 2009 | 1999 Nissan Quest

1 Answer

How do you remove the drivers side door panel on a 2000 nissan quest?


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls.

Sep 27, 2009 | 2000 Nissan Quest

1 Answer

Driver Side Sliding Door Won't Open at All - 07 Quest


Either it has rusted up or the mechcanisim has been bent,take door panel off check it out if rusted use some wd40 work lock untill it moves.

Jun 19, 2009 | 2007 Nissan Quest 3.5 Minivan

1 Answer

2007 Quest: The passenger side sliding door will not open


There is a wiring problem on your drivers side passanger door switch.

May 10, 2009 | 2007 Nissan Quest 3.5 Minivan

1 Answer

Replace driver side mirror on 2001 Nissan Quest


SECTION 501-09: Rear View Mirrors 2001 Villager Workshop Manual REMOVAL AND INSTALLATION Mirror —Exterior Rear View Removal
  1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
  1. Remove the upper speaker.
    1. Disconnect the electrical connector.
    1. Remove the bolts.
    1. Remove the speaker.
  1. Position the watershield aside.
  1. Remove the exterior rear view mirror access panel.
  1. Disconnect the exterior rear view mirror electrical connectors.
    • Release the wiring harness locator.
  1. Remove the exterior rear view mirror.
    • Remove the bolts.
    • Feed the wiring harness through the door opening.

Mar 31, 2009 | 2001 Nissan Quest

1 Answer

1994 Nissan Altima Passenger Door won't open


Since you have the door panel off, pul the rod for the door lock manually inside the door, this should unlock it, if it does not, there is a small push button, basicly a little peice of metal on the latch itself on the door latch inside the door, push it down this should pop the door open, you may need to spray all of the mechinisms with white lithium grease in a arosol can.....

Nov 12, 2008 | 1994 Nissan Altima

3 Answers

How to access brake tail light to change


Tail light replacement is not as hard as it seems.
Tools needed:flat head screwdriver and a deep 5/32 socket(a pair of pliers will work).
Step 1: open trunk and pull back truck liner at tail light.There is a small button clip on liner.Use screwdriver to pop up the center of button clip,pull clip out of hole.
Step 2:You will see a black wire attached to the body of car with 2 white clips.Use screwdriver to pop clips off of studs.
Step 3:Remove the nuts from the studs and pull tail light assembly straight back away from car.The outer side of the light just snaps in and out of place.
Step 4:Turn light socket counter clockwise 1/3 turn and pull out.
Step 5:Pull bad bulb straight out and replace.Reverse steps to reassemble.

Oct 24, 2008 | 2007 Nissan Sentra 2.0 SL Sedan

Not finding what you are looking for?
2007 Nissan Quest Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...