Question about Ford Cars & Trucks

Open Question

I have a1974 ford with HEI DIST AND VOLT REG IT WILL NOT CHARGE.

Posted by RONALD LOPER on

Ad

1 Related Answer

moparownr

Jeff Hammack

  • 667 Answers

SOURCE: 460 points out hei in

The setting for the plug gap on a model with HEI ignition is 0.44. Hope this helps, let me know.

Posted on Oct 26, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What do the symbols P and S stand for on terminals of the tachometer? 1978Chev.305 gas engine with distributor and coil.......jn my boat


tach hook up for chevy with hei distribitor is 1)white wire ; 12volt source 2)red wire -12 volt ignition switch (+) 3)black wire -battery ground (-) green wire ; to tach terminal on dist. / if it not hei with points just put green wire to neg. (-) side of coil

Nov 05, 2010 | Chevrolet Caprice Cars & Trucks

1 Answer

Wire my stewart-warner tach into a CHEV HEI ignition


Most HEI dist are labeled on the coil cover where the module/ power plugs in on the side of the cap It should be the only unused space there , unless you had a factory tach. You will need a plain female spade on you tach input wire and it should plug right in

Mar 14, 2010 | 1987 Chevrolet V30

2 Answers

460 points out hei in


I would run .044 to .052.

Oct 25, 2009 | Ford F-250 Cars & Trucks

1 Answer

Wiring an hei distributor


You shouldn't need a spark box because thee coil is located in the dist. cap. You need to run a 12v switched power source to the side of the dist. cap that is marked dist. if it isn't maked it is the term. that is on the front right of the conector pad. the one on the left is for hooking up a tach.

Oct 04, 2009 | 1986 Chevrolet C1500

3 Answers

1990 Jeep YJ 6 cyc. Won't Start---No Spark From Coil


It would be great if you could find the Ignition Control Module!!! From my experience on my Jeep...90 YJ 4.2 liter carb. it does not have one...Computer controlled only...

May 17, 2009 | 1990 Jeep Wrangler

1 Answer

Need wireing diagram to change 72 nova over to hei distributor


Hey , just take the positive wire from the coil you are removing and feed it to the + terminal on the HEI dist. cap.the other terminal under there is for your tachometer. If you are mounting a master kill switch in the bumper for drag racing- attatch the kill wire to the tach terminal also.
Thats it you just plug the three wire pigtail from the dist. base(pickup) to the cap and you are off.
Remember firing order is 18436572 in a clockwise direction. to find #1 remove #1 plug and have someone"bump" the engine over while holding your finger over the hole-carefull. then line up the slotted mark on the crank pulley with the big notch on the timing indicator. Good luck

Aug 31, 2008 | Chevrolet Chevy Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...