Question about 2005 Ford Excursion

2 Answers

2005 ford excursion cam sensor location I need to change the cam sensor and the crank sensors on my excursion and i do not know where they are located

Posted by liebscher3 on

  • Anonymous Mar 12, 2014

    where is the cps located on a v10 2000 Ford Excursion

×

Ad

2 Answers

Paul Fernandez

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 13 Answers

Cam sensor bottom of engine p.s. before you replace part ford has a recall on the cam sensor and might replace free of charge

Posted on Jun 01, 2015

Ad

Charles Baker

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 62 Answers

On my 02 Excursion with the 7.3L Diesel, the Cam Position Sensor is located at the front bottom of the engine on the passengers side. There is one electrical pigtail plug that is attached and one bolt holds the sensor in position. It may be located in a similar location on your 05 Ex. I do not know where the crank sensor is located. I hope this helps.

Posted on Sep 27, 2010

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2003 Ford Excursion V10. Just replaced both crank and cam position sensors, and still won't start, but will crank over. I'm a DIY. Any suggestions on my problem?


Do u hear your fuel pump kick on the three thing needed for a vehicle compression fuel and spark one of those will stop your vehicle from starting so or single coil pack but I think there individual now

Nov 14, 2015 | Ford Cars & Trucks

1 Answer

1999 tahoe crank/cam sensor?


the 5.3 and 6.0 are famous for bad crank sensor. never a problem with cam sensor. the crank sensor is located behind the starter. you need to remove starter to get to it. ther is one bolt holding it in. check the wires going to the sensor because they are so close to the exhaust the get brittle and brake. if the wire is good change sensor and your car will run fine

Mar 21, 2013 | 1999 Chevrolet Tahoe

1 Answer

2005 for escape,, stopped running,, wont start,, changed cam and crank sensors,, mechanic said no signal coming from new cam sensor that checks good OFF of engine,, wiring has been checked,,crank sensor is...


P1381 Cam Timing Advance is excessive if it were that your check engine light would be on it would be throwing code were gonna test what hes saying

Dec 11, 2010 | 2005 Ford Escape

1 Answer

Where are the cam sensors (2) located on my 2005 chevy colorado


I have a 2005 and the things that go bad on it is when the sensor goes off then for the intake then where the butterfly is on the intake gets dirty and needs to be cleaned it is the venturi gets dirty and needs to be cleaned and if it is a cam crank then it is the cam actuator that needs fixed you can tell if you take it off and there a screen missing it is a good sign that it needs be replaced and it is on the left side of the engine you need to understand that if it gives you a code that tells you that it is a sensor that is telling you that what the sensor looks after is bad not the sensor

Apr 11, 2010 | 2005 Chevrolet Colorado

1 Answer

My enigne is getting fuel but will not start. It is a 7.3 diesel


Repairing the 7.3L PowerStrokes can be hit and miss, there can be a number of things wrong and even a combination of things. The first thing I would try changing, if engine is turning over, is to change the Cam Position Sensor (aka CMP sensor). This is a Ford recalled sensor that is easy to change. It is located on the front, bottom, passenger's side of the engine. It only requires that you remove the electrical plug-in on the sensor and remove one bolt and the sensor should come out with some wiggling. Install the new sensor the opposite way you took the old one off. If that does not work then come back to fixya and we'll help you figure it out.

Mar 04, 2010 | 2001 Ford Excursion

1 Answer

My Excursion stopped several times on freeway


If your Excursion has the 7.3L Diesel, what I first suspect is the Ford recalled item Cam Position Sensor (CMP sensor). If your nearby Ford dealership has not replaced it for free for you, then make an appointment and take the car in to have the sensor replaced. If this does not solve your stalling problem, come back to FixYa and I will assist you further.

Apr 06, 2009 | 2000 Ford Excursion

Not finding what you are looking for?
2005 Ford Excursion Logo

688 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14866 Answers

Mike

Level 3 Expert

4372 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...