What is the gap on the spark plugs for 2000 grand am

Spark Plug Gap - AutoZone

www.autozone.com/.../specificationsMain.jsp?...Spark+Plug+G...

AutoZone2004 Mercury Grand Marquis 4.6L SFI 8cyl ' Specifications ' Spark Plug Gap.

AstroSafari.com • Spark plug gap size?

www.astrosafari.com/viewtopic.php?f=43&t=81409

Jul 27, 2015 - You're doing a '96? I think EARLIER 2nd Gen 4.3's used a .045" gap ; I believe it changed in 2000 or 2001 but don't quote me on that. All i'm ...Missing: gov

AstroSafariVans.com • View topic - spark plug gap question

astrosafarivans.org > ... > ENGINES GENERAL/PERFORMANCE

Nov 28, 2012 - 15 posts - ‎4 authors
My question is do I gap the spark plugs per 89 4.3 specs or do I use the 95 .... The vortec heads for a V8 chevy are 1996 and up however there ...Missing: gov

What is the proper sparkplug gap? - CarGurus

www.cargurus.com > Questions > GMC > Jimmy

CarGurusMar 16, 2013 - My Haynes manual and various places I've seen online say the gap is .045 inches ... spark plug gap for 1992 4.3 160 HP? ... Used GMC Safari".Missing: gov

[PDF]2000 GMC Safari Owners Manual - GM Extended Warranty

www.vadengmpp.com/owners-manual/gmc/2000-GMC-Safari.pdf

distributor --.025"
efi electronics .055"

Your best bet is manual or manufaturer. Try pre-set gaps - you might be lucky if you use OEM spark plugs or the brand similar to vehicle .

Most, if not all, spark plugs today are factory set for your car. That's because cars are using "standard" spark plug settings, usually around 40 or 45 thousandths of an inch. It's been about 20 years since I needed to gap a new plug.

all new spark plugs pre gapped and the plugs can not be gapped. all new cars use a spcial plug

Hi, the spark plug gap is .035...

Hello, here is the spark plug gap for this vehicle.

Spark Plug Gap: 2.2L Engine LN2 0.00157mm.(.040 in.)
2.4 quad engine Spark Plug Gap: 1.27 mm (050 in)

The plug gap is .040

The spark plug gap should be posted on the emissions sticker under the hood. The gap setting posted on the sticker is good for all brands and types of plugs for your vehicule

Hello, I hope this info helps...(subytech1)...REMOVAL
In this engine, each individual spark plug is located under each ignition coil.

1. Prior to removing spark plug, spray compressed air around base ofignition coil at cylinder head. This will help prevent foreign materialfrom entering combustion chamber.
2. On this engine each individual ignition coil must be removedto gain access to each spark plug. Refer to Ignition CoilRemoval/Installation.
3. Check condition of coil O-ring and replace as necessary.

1. Inspect spark plug condition. Refer to Spark Plug Conditions.

CLEANING
Theplugs may be cleaned using commercially available spark plug cleaningequipment. After cleaning, file center electrode flat with a smallpoint file or jewelers file before adjusting gap.

CAUTION: Never use a motorized wire wheel brush to clean sparkplugs. Metallic deposits will remain on spark plug insulator and willcause plug misfire.

ADJUSTMENT

Setting Spark Plug Gap - Typical
Check spark plug gap with a gap gauge tool. If the gap is not correct,adjust it by bending ground electrode. Never attempt to adjust gap bybending center electrode.

INSTALLATION

CAUTION: This engine is equipped with copper core groundelectrode spark plugs. They must be replaced with the same type/numberspark plug as the original. If another spark plug is substituted,pre-ignition will result.

Special care should be taken when installing spark plugs into cylinderhead spark plug wells. Be sure plugs do not drop into plug wells asground straps may be bent resulting in a change in plug gap, orelectrodes can be damaged.

Always tighten spark plugs to specified torque. Over tightening cancause distortion resulting in a change in spark plug gap or a crackedporcelain insulator.

1. Start spark plug into cylinder head by hand to avoid cross threading.
2. Tighten spark plugs to 27 Nm (20 ft. lbs.) torque.
3. Before installing coil(s), check condition of coil O-ring andreplace as necessary. To aid in coil installation, apply silicone tocoil O-ring.
4. Install ignition coil(s). Refer to Ignition Coil Removal/Installation.