-
Oldsmobile Master
2,993 Answers
- Posted on Aug 25, 2009
Re: 1990 cutlass ceira how do you replace drivers door...
Outside Mirrors
REMOVAL & INSTALLATION
Standard
- Remove the door trim panel and detach the inner panel water deflector. With the glass in the down position, pull out the front portion of the glass run weatherstrip.
Fig. 1: Unfasten the attaching nuts from the mirror base studs, then remove the mirror
- Remove the attaching bolts and screws from the front glass run channel lower retainer to filler, then rotate retainer rearward.
- Remove the noise control patch to gain access to the screw at the belt, then remove the screw.
- Remove the filler attaching screws at the top front of the window frame, then remove the mirror and filler from the door.
- Remove the attaching nuts from the mirror base studs, then remove the mirror.
To install:
- Be sure that the mirror gasket is aligned.
- Replace the mirror and filler on the door. Install the filler attaching screws at the top front of the window frame. Attach the nuts to the mirror studs and tighten.
- Install the screw at the belt, then insert the noise control patch.
- Insert the retainer, then install the attaching bolts and screws to the front glass run channel lower retainer to filler.
- Replace the front portion of the glass run weatherstrip, insert the inner panel water deflector, then reinstall the door trim panel.
Manual Remote
- Remove the mirror remote control escutcheons and door trim panel. Detach the inner panel water deflector.
NOTE: Right side remote mirror may require detaching part of the instrument panel.
- With the glass in the down position, pull out the front portion of the glass run weatherstrip.
- Remove the attaching bolts and screws from the front glass run channel lower retainer to filler and rotate retainer rearward.
- Remove the noise control patch to gain access to the 0.3 in. (7mm) screw at the belt and remove the screw.
- Remove the filler attaching screws at the top front of the window frame.
- Remove the mirror base with mirror and cable assembly from the door.
- Remove the mirror to filler attaching nuts and remove the mirror and cable from filler.
To install:
- Be sure cable is routed around front glass run channel retainer and installed to clip.
- Install and connect the cable to the filler.
- Attach the filler nuts to the mirror, then tighten to 72 inch lbs. (8 Nm).
- Install the mirror base with the mirror and cable assembly to the door.
- Insert the filler attaching screws to the top of the window frame, then install the screw to the belt.
- Secure the noise control patch.
- Attach the bolts and screws to the front of the glass run channel lower retainer and filler.
- Install the glass run weatherstrip.
- Attach the inner panel water deflector, door trim panel and mirror remote control escutcheon.
Electric Remote
- Disconnect the negative battery cable.
- Remove the mirror remote control escutcheons and door trim panel. Detach the inner panel water deflector and the electrical connector for the mirror.
NOTE: Right side remote mirror may require detaching part of the instrument panel.
- With the glass in the down position, pull out the front portion of the glass run weatherstrip.
- Remove the attaching bolts and screws from the front glass run channel lower retainer to filler and rotate retainer rearward.
- Remove the noise control patch to gain access to the 0.3 in. (7mm) screw at the belt and remove the screw.
- Remove the filler attaching screws at the top front of the window frame.
- Remove the mirror base with mirror and electric connector from the door.
- Remove the mirror to filler attaching nuts and remove the mirror and electric wire from filler.
- To install, reverse Steps 1 through 6. Be sure electric wire is routed around front glass run channel retainer and installed to the clip. Tighten the nuts to 72 inch lbs. (8 Nm).
- Connect the negative battery cable, then reset the clock, radio and any other accessories if required.
×