Question about 1990 Dodge Spirit

1 Answer

I replaced the timing belt , Need to know where the mark is for cranshaft?

Posted by evealv72 on

Ad

1 Answer

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 65 Answers

It should be on the pulley on the end of the crankshaft, should indicate zero on the index mark on the pulley

Posted on Aug 22, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the timing marks for a 1994 Mecury Capri?


need to aling timing marks for the camshaft to the marks on the valve cover marks and the dot on the cranshaft gear to the oil pump housing mark

Sep 05, 2014 | 1994 Mercury Capri

1 Answer

My engine keeps sputtering. I have a 2005 pontiac grand am 3.4 liter V6. I've replaced the spark plugs due to a misfire, I've replaced the cranshaft sensor, I checked the timing on the timing


fuel pump could be going bad check fuel pressure that will make it sputter,if that not the case check fuel filter.
do a compression test on cylnders

Mar 01, 2013 | 2001 Pontiac Grand Am SE

1 Answer

The timing belt is broke, how can reemplace and


Take off the alternator belt, tensor, fan and cap of timing belt, review the mark of cranshaft pulley must be in 10grades BTC The grades are on the cap, then review the mark valves pulley and put the timing belt (Note disconect the battery in order to delete the failure) placement again all the parts and thats all.

Jan 12, 2010 | 1991 Ford Ranger Supercab

1 Answer

We are replacing timing belt and need to know the markings to aline the timing belt up correctly.


Ok Block this brand right in the bracket of the alternator. Block cover the time left is belt.Cranshaft witha brand that is in the oil pump

Oct 18, 2009 | 1999 Dodge Caravan

1 Answer

Cylinder head removal


IF YOUR ENGINE IS A 3.0 V6 3VZ-E YOU REMOVE AIR INTAKE PIENUM,AND ALL SURROUNDING COMPONENTS REMOVE THE FUEL RAIL THE INJECTORS ATTACHED ,REMOVE INTAKE MANIFOLD,THEN YOUR EXHAUST CROSSOVER PIPE,EXHAUST MANIFOLDS REMOVE ALL BELT'S AND PULLEYS ,TIMING COVER .....BEFORE REMOVING YOUR CRANSHAFT PULLEY ,ALIGNMENT YOUR TIMING MARKS ,ON CAMSHAFT TIMING PULLEY LT,RT ,CRANKSHAFT TIMING PULLEY,THEN REMOVE TIMING BELT TENSIONER ,REMOVE ALL CAM SHAFTPULLEY'S AND CRANKSFT . REMOVE DISTRIBUTOR.REMOVE HEADCOVERS,CAMSHAFT,THEN YOU COULD GET TO THE HEAD BOLTS.

Apr 02, 2009 | 1993 Toyota Pickup

1 Answer

Put new oilpump and hadto remove timeing belt and gears. i need t


For the 1986 Dodge Ram 50 2.0L AND 2.6L 4-Cylinders:

Firing Order:
1-3-4-2

Cylinders:
(back)
...4
...3
...2
...1
(front)

Distributor:
.(back)
3.......4
1.......2
.(front)

For the Timing Marks: Click on the following Link. It has the Position of the Cranshaft and Camshaft and their respective marks.

http://www.2carpros.com/car_repair_information/year/1986/make/dodge/model/ram_50/1986_dodge_ram_50_timing_belt_diagram_marks.htm

Jan 02, 2009 | 1986 Dodge Ram 50

1 Answer

1999 nissan quest


Rigoe the points for the timing belt are usually located on the sprokets in conection with marks or dots on the engine block some where around the sprockets that hold the timing belt. Remenber to bring the piston number one to TDC (top dead center), this means you have to locate the piston number one, take the spark plug out and turn the cranshaft (the one with the pulley) by hand until the piston is all the way up. On the distributor the rotor should point to the spark-plug wire number one (you can make a mark outside of the distributor cap where the number one spark-plug wire is pointing so when you take the cap off you can see if the rotor is pointing the same direction). With the timing belt cover off you are going to be able to aling all this points at the exact locacation all together. So we have: Piston number one at TDC, The rotor(enside the distributor cap) pointing to the number one spark-plug wire, and the mark of the sprockets pointing the marks of the engine block( litle dot or dash). If you get all this right you are have done a good job and ready to make a trip you can get all this just by turning the cranshaft by hand with a rachet and a big socket. God bless you.

Dec 06, 2008 | 1999 Nissan Quest

1 Answer

Instaling a timing belt on 2002 daewoo lanos


I have a 2001 Lanos and I've replaced my belt twice (after breaking the first one at speed and having to replace the engine). The two cam gears have timing marks that should point towards each other. If you hold a ruler up with the edge of it passing through the center of the cam shaft bolts, the timing marks on each cam should be lined up on with the edge of the ruler and pointing towards each other. The crankshaft gear (not the big pulley) has a small triangle timing mark on it that should point almost straight down. There is a V cut into the oil pan that actually should line up with the cranshaft timing mark. BE VERY CAREFUL because if you rotate the crankshaft independently of the cams, you can tear up the valves very quickly.

Dec 05, 2008 | 2002 Daewoo Lanos

2 Answers

Crancshaft pullt jamming up


You must have #1 on TDC and the camshafts on the timing mark to fit a new belt , I rekon yer valves are fouling the piston .
Ignore the mark on the pump pulley .

Nov 25, 2008 | 1998 Isuzu Trooper

1 Answer

Is my timing correct?


it was good to check how timing is before you removed old belt.
anyway first before you fited new one rotate the engine by hand look front crankshaft timing mark,
put piston number one should top dead center look cranshaft mark.when you done.
second step is to set up camshaft check timing mark on the camshaft follow the marks fisr cylinder.

Sep 17, 2008 | 1999 Hyundai Accent

Not finding what you are looking for?
1990 Dodge Spirit Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...