2003 Dodge Intrepid Logo
Posted on Aug 21, 2009
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

THE CAR THAT WON'T STOP BREAKING

I AM SO SICK AND BROKE OVER THIS CAR. I'VE REPLACED THE CRANK CENSOR,WATERPUMP,HEAT CENSOR, AND EVERYTHING ELSE THAT HAS FELL OFF OF THIS CAR. I CAN'T AFFORD TO LET IT GO BACK,BUT I CAN'T KEEP FIXING THIS CAR EVERY PAYDAY. AND YET IT IS STILL RUNNING HOT . ANY IDEAS?

Answer This Question
  • Anonymous May 11, 2010

    your cars engine size matters in this question. does your car have a 2.7 engine? please let me know, and we'll find out what's going on. it really does matter what size the engine is on this particular car. thanx

×

2 Answers

Henry Linley

Level 2:

An expert who has achieved level 2 by getting 100 points
Hot-Shot:

An expert who has answered 20 questions.
Corporal:

An expert that has over 10 points.
Mayor:

An expert whose answer got voted for 2 times.

  • Expert 44 Answers
  • Posted on Aug 28, 2009
Henry Linley
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points
Hot-Shot:

An expert who has answered 20 questions.
Corporal:

An expert that has over 10 points.
Mayor:

An expert whose answer got voted for 2 times.

Joined: Jul 19, 2009
Answers
44
Questions
0
Helped
19685
Points
120

Check your themorstate make sure the water is circulating in the radiater.

Anonymous

Level 2:

An expert who has achieved level 2 by getting 100 points
MVP:

An expert that got 5 achievements.
Governor:

An expert whose answer got voted for 20 times.
Scholar:

An expert who has written 20 answers of more than 400 characters.

  • Expert 113 Answers
  • Posted on Aug 28, 2009
Anonymous
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points
MVP:

An expert that got 5 achievements.
Governor:

An expert whose answer got voted for 20 times.
Scholar:

An expert who has written 20 answers of more than 400 characters.

Joined: Jun 03, 2009
Answers
113
Questions
3
Helped
48491
Points
273

Test your coolant if it is in specs.(you can get coolant tester from local auto part store for a low price) if it is not drain the coolant and use proper 50/50 mix coolant.
water pump and coolant temp sensor you had change already . get new pressure cab and make sure you dont have any leak from coolant system and run the car and check coolant fan works when engine reach or past the normal operation temp. if it not working you have to fix the fan but it is runing and you still have over heat should be pressure cab.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

96 jeep laredo stopped running gages quit and won't start even after replacing crank shaft sensor but it turns over like it wants to start
Crank sensor wont have any effect on starting, Cam position sensor would. Also check all your fuses.
Read full answer
Mar 27, 2013 • Cars & Trucks
0helpful
1answer

The Heat only works on defrost and on the floor. Cannot get the heat to come out of the vents.
If you have heat then you need look no farther with coolant. The only problem you have is with the damper that is controlled by the switch method on dash. Either something is undone or stuck. Sometimes a vacuum line is disconnected. Good luck. Oh, don't force anything under dash, plastic breaks easily.
Read full answer
Feb 23, 2013 • 1993 Cadillac Eldorado
0helpful
1answer

Just dies, sometimes won't start. Changed crank shaft censor, still no good
ihave a 98 grnd chrk lrdo had to replace computer on fire wall, periodicly i spray all electrical connections w/ crs electric contact spray.
Read full answer
Jun 01, 2012 • 2000 Jeep Grand Cherokee
0helpful
1answer

Replaced the crank shaft censor, coil, wires, plugs, cap and roter, fuel pump and filter. Drove fine for a couple weeks and now won't start and getting no spark...what could I do or try??
I did that job once on my car, then the same thing happened.. you most like'lly installed it wrong.. pull it apart and see if pieces broke off it... what kind of car is it ?
Read full answer
Apr 22, 2012 • 1992 Jeep Wrangler
0answers

92 plymouth laser rs turbo won't will crank but not start
Read full answer
Be the first to answer Apr 02, 2017 • Cars & Trucks
0helpful
1answer

I put in a trans the crank position censor wire is broke can i by pass it or does it have to be hooked up
Almost a foolish question

It won't even start without a CPS Signal

How would the PCM know where the pistons
where, at any given time?

Solder & heat shrink the damaged wires
Read full answer
Jun 11, 2011 • 1995 Jeep Grand Cherokee
0helpful
1answer

I was driving and my car lost all power and won't restart I've been told the engine is seized solid and the timing chain is broke and that's why it wont work but the wheel's didn't lock...
I assume your S class is an automatic gearbox ,hence the roll to a stop when engine seize/cam chain break.the symptoms of a camchain break would be the valves will hit the pistons causing major damage to valves, pistons,cylinder head, conrods, bores and possibly crank.Its possible that the engine seized first causing the chain to break,either way it would be a seriously expensive/terminal engine problem.
Read full answer
Jun 01, 2011 • 2001 Mercedes-Benz S-Class
0helpful
2answers

Do the valves have clearance if timing belt breaks, or are the valves bent?
Hi,
some cars had the 'free wheel" feature if the cam belt broke, thus saving the valves. I do not think that your vehicle had the feature. However, if you gave more info0, ie, is the car running or not, then there might be an easy way to check the head out.
Read full answer
Jan 31, 2011 • 1988 Toyota Camry
0helpful
1answer

Mystery car
it sounds to me like a bad censor...you would probably have to take it to a shop for them to run a diagnosic test, that should tell you what censor.
Read full answer
Jun 18, 2009 • 2000 Dodge Stratus
0helpful
1answer

Cranks but wont turn over
you know. i took it to a mechanic and actually.... The timing belt cut the Crank Shaft Censor... So it was the crank shaft censor again. The wires were routed wrong from the first mechanic that "fixed" the car.
Read full answer
Aug 01, 2008 • 2000 Hyundai Sonata
Not finding what you are looking for?

View Most Popular

2003 Intrepid

  • Cars & Trucks

Related Question

96 jeep laredo stopped running gages quit and won't start even after replacing crank shaft sensor but it turns over like it wants to start

  • Cars & Trucks

Related Topics

81 views

Ask a Question

Usually answered in minutes!

Popular Questions

NECESITO, VER COMO VA LA CADENA DEL TIEMPO DE

2000 Dodge Intrepid

2002 Dodge Intrepid transmission not shifting

1997 Dodge Intrepid

Location of camshaft sensor on a 3.5 dodge intrepid

2002 Dodge Intrepid

Need diagram to replace timing

Dodge Intrepid Cars & Trucks

2002 Dodge Intrepid transmission not shifting

2002 Dodge Intrepid

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Dodge Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...