Question about 2002 Mitsubishi Lancer

Open Question

Hi,i dont know what is the head torque of my mitsubishi lancer 4g15 2002 model pleae help me thanks.

Posted by Anonymous on

Ad

5 Related Answers

emissionwiz

Marvin

  • 85239 Answers

SOURCE: head torque settings

The torque is 90 foot lbs, and they want you to use new bolts, the old ones are stretched and CAN NOT be reused, tighten 20 lbs at a time in proper sequence as outlined in service manual.

Posted on Dec 03, 2008

Ad

Anonymous

  • 122 Answers

SOURCE: need cylinder head gasket torque specs.

looks like there is special sequence to reassemble and tightening, a quick note replace any bolts that have two punch marks.tighten as follows: x x x x x 10 4 2 6 8 x x x x x 7 5 1 3 9 torque all down to 15 ft lbs torque to 30 ft lbs plus 90 degrees. Good luck!

Posted on Sep 18, 2009

Ad

tberan1

  • 523 Answers

SOURCE: Torque specs for mighty max

Per my Chilton's manual tehe bolts should be (cold engine) 65 to 72 FT. Pnds., the cam shaft bearing bolts should be 8x25 = 15 - 19 Ft pnds and the 8x65 should be 14 - 15 Ft Pnds.

The sequence is as follows for the (10 ) head bolts:

7 - 5 - 2 - 4 - 10

9 - 3 - 1 - 6 - 8

I hope this may help,
Tom

Posted on Oct 15, 2009

Oyelade Gbenga

  • 713 Answers

SOURCE: hi..where can i download repair manual for lancer GLXi 2005

Hi,you can download the manual for your mitsubishi at www.manualsonline.com,www.manualnguide.com and www.mitsubishi.com. please don't forget to rate this solution positively Thanks and good luck

Posted on Apr 19, 2010

heimlich

David Belcher

  • 1978 Answers

SOURCE: Hi, I need to know when I need to change the

The owners manual says nothing about ATF change intervals. The warranty manual says check it regularly. In the severe service section of the warranty manual it says for severe duty change it at 30,000 miles(48,000 kilometers). I would consider changing the ATF no later than 50,000 miles(80,000 kilometers). Mitsubishi cars use there own Diamond ATF SP III. If you do not change it by 60,000 to 70,000 miles (96,000 to 113,000 kilometers) the transmission may start to act funny when shifting. Regular changes will keep you from experiencing this problem. Be sure to use genuine Mitsubishi Diamond ATF SP III or a synthetic equivalent.

Posted on Sep 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Engine torque settings mitsubishi 4d32


im looking for information by a 4d32 Mitsubishi , help!!!!!! thanks

Apr 03, 2012 | 1988 Mitsubishi Cargo

1 Answer

Torque the cylinder head bolts for mitsubishi lancer 2002


Try this
I dont know which engine you have.

420a
1. Torque all center bolts to 25 ft-lbs, torque the 4 corner bolts to 25 ft-lbs
2. Torque all center bolts to 50 ft-lbs, torque the 4 corner bolts to 50 ft-lbs
3. Re-Torque all center bolts to 50 ft-lbs, re-torque the 4 corner bolts to 50 ft-lbs
4. Tighten all bolts in the sequence from #1-#10 an additional 1/4 turn.

7-Bolt 4G63
1. Torque all bolt to 58 ft-lbs in order
2. Loosen all bolts completely to 0 ft-lbs
3. Torque all bolts to 15 ft-lbs in order
4. Tighten all bolt 1/4 turn in order
5. Tighten all bolts an additional 1/4 turn in order.

ARP Head Studs
1. Tighten all bolts to 40 ft-lbs
2. Tighten in steps of 10 ft-lbs increments until the specified torque that you are looking for is reached. This can vary with the amount of boost you plan on running.

Jun 30, 2011 | 2002 Mitsubishi Lancer

1 Answer

Hi i want to know how to remove the air con. filter of my mitsubishi lancer mx 1998. and also how to make the air cooler inside. thanks


you make the air cooler by adding freon but too much will be same as too little dont over due it and air conditioners air filter is called a cabin air filter and you pull out your glove box and theres two bolts to remove the cover for cabin air filter hope this helps

Sep 16, 2010 | 2003 Mitsubishi Lancer

1 Answer

I want to remove the cylinder head bolts on a 2003 Mitsubishi Lancer?


Get the factory repair manual it will give you the correct procedure and torque values for the bolts.

Mar 29, 2010 | 2004 Mitsubishi Lancer

1 Answer

Need torque spec for axle nut 2003 lancer


THE BIG NUT DONT TORK IT SHOULD HAVE HAD A CARTER PIN IN IT THAT KEEPS IT FROM BACKING OFF BUT U JUST SNUG IT UP TIGHT THIN TURN 1/2 TURN PUT CARTER PIN IN THE HOLE IF U TIGHTING THIS NUT REAL TIGHT THE BEARING WILL GET HOT AND LOCK UP ON U GOOD LUCK PLEASE RATE THIS

Apr 05, 2009 | 2003 Mitsubishi Lancer

2 Answers

Planning to buy a 2001 lancer, auto gear...am I doing right?


the lancer get's about 23-26 miles per gallon it is a low maintenance vehicle and as long as you change the oil and do regular maintenance on it the vehicl will last a long time... please rate this

Oct 03, 2008 | 2002 Mitsubishi Lancer

Not finding what you are looking for?
2002 Mitsubishi Lancer Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...