Question about 2006 Chevrolet Colorado

2 Answers

How to replace 2006 chevy colorado thermostat

Posted by morales_esth on

Ad

2 Answers

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Find where top hose comes from the radiator into the engine block, then drain some of the coolant out and remove hose and thermostat from the block. remember which way the termostat sits in the block and install new one. its always a good idea to flush your cooling system before putting in a new thermostat. if the old one was plugged up, the gunk thats in your system will just plug up the new one in time too. you can get a bottle of radiator flush from most auto parts stores.

Posted on Aug 23, 2009

  • 1Cecelia1 Sep 10, 2011

    Ok so that sounds real easy. If you have acctually tried to change one of these you would know that you can't even get your hand in to where the hose clamp and bolts are to take the think off. So the first explaination would be how to get to it.

×

Ad

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

How do you remove the clamp, i cant seem to take it off. is there a trick to it?

Posted on Aug 07, 2011

  • 1Cecelia1 Sep 10, 2011

    Were you successful at getting your hand to the clamp? I'm not able and I have a small hand.

×

Ad

5 Related Answers

alicantecoli

Colin Stickland

  • 22485 Answers

SOURCE: I need to replace the blower resistor on my 2006

around the blower motor ,its all in one

Posted on Dec 27, 2009

Anonymous

  • 1 Answer

SOURCE: 2006 colorado intermittently fails to start. It

Clean all the electrical connections you can get to under the hood with automotive electronics cleaner,dry with compressed air and pack each connector with di-electric grease.

Posted on Nov 13, 2009

c17hydro

Greg Bernett

  • 2993 Answers

SOURCE: how do i change out the knock sensor on a 2006 chevy colorado

You didn't list your engine size so please pick the applicable to your motor size:

Removal & Installation 2.8L & 2.9L Engines To Remove:

  1. Lift the vehicle high enough to gain access to the knock sensor (KS) through the left front wheelhouse.
  2. Remove the left front wheel and wheelhouse liner.
Knock sensor (KS) (A), Engine harness (B), Knock sensor (KS) connector (C)


e44e83f.gif
  1. Disconnect the knock sensor (KS) connector.
  2. Detach the knock sensor (KS) from the engine block.
To Install:
  1. Attach the knock sensor (KS) to the engine block.
    • Tighten the bolt to 18 ft lbs (25 Nm).
  2. Connect the knock sensor (KS) connector.
  3. Install the left front wheelhouse liner and wheel.
  4. Fully lower the vehicle.

Posted on Sep 03, 2009

Anonymous

  • 1 Answer

SOURCE: 2006 chevy colorado install brake shoes

how do you replace brake pads

Posted on Oct 10, 2010

Anonymous

SOURCE: Gas cap off on 2006 chevy Colorado and check

You have other EVAP System issues

The Gas Cap, being okey would turn off the light

Posted on Dec 15, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Replace camshaft postion actuator solenoid 2006 chevy impala

Have any codes ? Chevy Colorado P0017 Case Study Part 1 Doesn't matter if this is a Colorado . Same on impala VVT - variable valve timing .
0helpful
2answers

2006 cheevy colorado reduced powereduced power wont run 2006 chevy colorado pick up code 600 and 601

Those are communication and internal computer failures. You likely need a new PCM
1helpful
1answer

My 2006 chevy colorado is making a clicking sound and won't turn over

Your Main Battery is Flat, get a jump start if its safe or remove the battery and hook it up to a charger. Maybe you left your lights on, or your alternator isnt charging the battery properly when your driving around. Sometimes this can be the bushes located in the alternator.
0helpful
1answer
0helpful
1answer

Gas cap off and engine light came on in 2006 Chevy Colorado. Replaced gas cap now how do I get check engine light off?

If all it was is that you did have it off it will reset by the 3rd drive cycle. It may take between 50 & 200 miles.
3helpful
1answer
0helpful
1answer

Plugs on 3.5 Chevy Colorado

Have him go to The Local Auto Parts Store and Purchase a Haynes or Chilton Book on this Truck. Costs 25.00 But, will tell you how to fix ANYTHING that goes Wrong. You can get them also at their Websites.
Not finding what you are looking for?
2006 Chevrolet Colorado Logo

7,834 views

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6928 Answers

john h

Level 3 Expert

24971 Answers

Ryan Lutton
Ryan Lutton

Level 3 Expert

1267 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...