Question about Honda Cars & Trucks

Open Question

2000 honda gl1500 goldwing replace headlight assembly

Light not working,still not working, took off the assembly and cannot fit it back

Posted by Anonymous on

Ad

5 Related Answers

Anonymous

  • 34 Answers

SOURCE: 2000 Honda Accord Headlight Assembly

what i suggest i can suggest is, buy a clear sealant, and seal the sides of the headlights.

the reason why is air can creep in tha lamps that's why it gets moisture (foggy) and dirty.

hope it helps.

Posted on Aug 27, 2008

Ad

Anonymous

  • 1 Answer

SOURCE: headlight assembly

you will have to remove the front bumper cover to get to 2 bolts and also the grille to get another bolt off also there are are a total of 5 bolts that hold it in. be careful taking it out as you can crack the mounting brackets for the assembly just be patiece it will come out.

Posted on Dec 09, 2008

Ad

Anonymous

  • 93 Answers

SOURCE: how to assemble a 2000 honda accord headlamps

Its actually pretty straight forward. Disconnect the headlight. Then their are two bolt on the top the the headlight. Remove those then remove the wheel of the car. Then their are three more bolts bellow the headlight All three facing from the outside of the fender to the center of the car.

Then once you have those 5 bolts out. Pull the headlight forward and up. Their are two tabs that go into the fender.

Posted on Dec 09, 2008

Anonymous

  • 837 Answers

SOURCE: REPLACE HEADLIGHT ASSEMBLY IN 2000 LINCOLN TOWNCAR

Open the hood and make sure the car and the lights are off.
Remove the plastic protective cover.There are 3 knobs,turn halfway and pull.Put aside and out of the way.
Remove the three pins that are holding the light assembly in place.These are flat rods with a little bend at the end.
Twist and un-plug the lights,now you can remove the whole lens.
The light bulbs can also be removed and replaced from this point.
Make sure all the bulbs are working before you put it back together.

Posted on Mar 13, 2009

dllowy

  • 4 Answers

SOURCE: Headlight bulb replacement for 2000 Caviler

Actually, you do not have to break it. Use a screwdriver to bias the assembly up over the oval hold where the tab goes it

Posted on Sep 19, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Adjust headlights


the bulbs are pre-set in focus and if fitted correctly in the head light assembly they will be focused and adjusted correctly. Try adjusting the whole head light assembly by the 3 screws / adjusting knobs at the back of the assembly to aim the head lights correctly.

Dec 24, 2013 | 2000 Volvo S70

1 Answer

Lights will not turn on


HEADLIGHTS NOT WORKING


It can be faulty headlight switch or issue with its wiring. Or its faulty head light fuse.


==========

To troubleshoot the issue i suggest you few help links with appropriate solution. So you can follow the test and confirm what exact problem is there in your case of headlights not working:-----

Click the link below: -----


All headlights not working?

http://repairhelpcenter.blogspot.com/2012/01/all-headlights-not-working.html

----------

Working of Headlight switch?
------------
Both headlight bulbs blow together?

------------
Car headlight bulbs don't last long?

---------------

2007 Dodge Caliber: Low Beam Headlight Not working

http://technoanswers.blogspot.in/2012/06/2007-dodge-caliber-low-beam-headlight.html

----------

2003 Toyota Camry: Headlights Work Intermittently?

http://technoanswers.blogspot.in/2012/04/2003-toyota-camry-headlights-work.html

----------

Chevy Tahoe: Low Beam Lamps are not working?

http://technoanswers.blogspot.in/2012/04/chevy-tahoe-low-beam-lamps-are-not.html

----------

2001 Chevrolet Tahoe: Headlights not coming ON?

http://technoanswers.blogspot.in/2012/04/2001-chevrolet-tahoe-headlights-not.html

--------

2004 Dodge Ram: High Beam Light is DIM?

http://technoanswers.blogspot.in/2012/04/2004-dodge-ram-high-beam-light-is-dim.html

----------

2001 Chevrolet Tahoe: Both Low Beam Lamps Not Working?

http://technoanswers.blogspot.in/2012/04/2001-chevrolet-tahoe-both-low-beam.html

------------

Low beam headlights Modification?

http://schematicsdiagram.blogspot.in/2012/04/low-beam-headlights-modification.html

---------
How to Replace a Headlight

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight.html

------------
How to Replace a Headlight Bulb


http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-headlight-bulb.html

-----------
How to Replace a Headlight Switch

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-headlight-switch.html

----------
How to Replace a Headlight Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight-assembly.html


How to Replace a Park Light Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-park-light-assembly.html

-----------

Low beam headlights Modification?

http://schematicsdiagram.blogspot.in/2012/04/low-beam-headlights-modification.html

----------

Headlight Assembly Removal On Honda Accord

http://technoanswers.blogspot.in/2012/06/headlight-assembly-removal-on-honda.html

---------------

Honda Headlight Assembly Removal
http://schematicsdiagram.blogspot.in/2012/06/honda-headlight-assembly-removal.html

-----------

How to Replace a Headlight Door

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight-door.html

----------

How to replace HID headlight bulbs for lexus 400h?

http://schematicsdiagram.blogspot.com/2012/01/how-to-replace-hid-headlight-bulbs-for.html

----------------

These will help.

Thanks.

Nov 28, 2012 | 1986 GMC K1500

1 Answer

REPLACE HEADLIGHT 2008 SPRINTER


On some cases there are few hidden clips holding the assembly from under hood,that has to be released to remove headlight .

There are few troubleshooting help links showing how to replace car headlights,i suggest you to refer the links to solve these issue.

--------
Click the link below:------
How to Replace a Headlight http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight.html

------------
How to Replace a Headlight Bulb


http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-headlight-bulb.html

-----------
How to Replace a Headlight Switch http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-headlight-switch.html

----------
How to Replace a Headlight Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight-assembly.html


How to Replace a Park Light Assembly http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-park-light-assembly.html

-----------
Low beam headlights Modification? http://schematicsdiagram.blogspot.in/2012/04/low-beam-headlights-modification.html

----------
Headlight Assembly Removal On Honda Accord http://technoanswers.blogspot.in/2012/06/headlight-assembly-removal-on-honda.html --------------- Honda Headlight Assembly Removal
http://schematicsdiagram.blogspot.in/2012/06/honda-headlight-assembly-removal.html-----------
How to Replace a Headlight Door http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight-door.html

---------
All headlights not working? http://repairhelpcenter.blogspot.com/2012/01/all-headlights-not-working.html

----------
How to replace HID headlight bulbs for lexus 400h? http://schematicsdiagram.blogspot.com/2012/01/how-to-replace-hid-headlight-bulbs-for.html

----------
Working of Headlight switch?
------------
Both headlight bulbs blow together?
------------
Car headlight bulbs don't last long?



----------------
These will help.
Thanks.

Nov 23, 2012 | 2010 Mercedes-Benz Sprinter

3 Answers

Replace headlight bulb


  1. INSTALLATION GUIDE:
  2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
  3. Parts Identification:
  4. Projector Headlight
  5. Halo & L.E.D.
  6. Bottom of the Headlight:
  7. Ballast Bracket, Halo Wires(red/black)
  8. Turn Signal Adaptor
  9. TOOLS REQUIRE
  10. 10mm - 8mm socket
  11. Philip Screwdriver
  12. Crimper/Pliers
  13. For more information about how to install your vehicle, come visit our youtube page on
  14. http://www.youtube.com/spyderauto
  15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
  16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
  17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
  18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
  19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
  20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
  21. STEP:
  22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
  23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
  24. Factory Xenon Headlight
  25. Spyder Projector Headlight using Factory Xenon Lights
  26. STEP:
  27. PLS VOTE ME
BMW e46 HID Headlight Replace
replace-headlight-bulb-afy5cnsznmokzumyhdcbeseq-5-0.jpg

replace-headlight-bulb-afy5cnsznmokzumyhdcbeseq-5-2.jpg

Nov 23, 2012 | 2000 GMC Denali

2 Answers

How do I get to the front headlight to change it


Re: Replace headlight bulb

  1. INSTALLATION GUIDE:
  2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
  3. Parts Identification:
  4. Projector Headlight
  5. Halo & L.E.D.
  6. Bottom of the Headlight:
  7. Ballast Bracket, Halo Wires(red/black)
  8. Turn Signal Adaptor
  9. TOOLS REQUIRE
  10. 10mm - 8mm socket
  11. Philip Screwdriver
  12. Crimper/Pliers
  13. For more information about how to install your vehicle, come visit our youtube page on
  14. http://www.youtube.com/spyderauto
  15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
  16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
  17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
  18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
  19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
  20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
  21. STEP:
  22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
  23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
  24. Factory Xenon Headlight
  25. Spyder Projector Headlight using Factory Xenon Lights
  26. STEP:
BMW e46 HID Headlight Replace
get-front-headlight-change-afy5cnsznmokzumyhdcbeseq-5-0.jpg

get-front-headlight-change-afy5cnsznmokzumyhdcbeseq-5-2.jpg

Nov 22, 2012 | Cars & Trucks

2 Answers

Headlights wont work and dash and parking lights come when ignition switch is turned on. sometimes jiggling wires works. what is the problem?


Check out related help links with solutions to troubleshoot these problem.
Click the link below directly:---
Heater fan and headlights will not turn off with ignition off? http://technoanswers.blogspot.com/2012/01/heater-fan-and-headlights-will-not-turn.html

---------
High beams stopped working but headlights still work?

http://howtobyme.blogspot.com/2011/11/highbeams-stopped-working-but.html

---------------
Only one head light works on 2001 Dodge Caravan? http://howtobyme.blogspot.com/2011/11/only-one-head-light-works-on-2001-dodge.html

----------------
Headlight Assembly Removal On Honda Accord http://technoanswers.blogspot.in/2012/06/headlight-assembly-removal-on-honda.html ------------- Honda Headlight Assembly Removal
http://schematicsdiagram.blogspot.in/2012/06/honda-headlight-assembly-removal.html-----------
All headlights not working? http://repairhelpcenter.blogspot.com/2012/01/all-headlights-not-working.html

----------
Headlight wiring diagram for 1997 Lincoln Town Car?

http://technoanswers.blogspot.in/2012/02/headlight-wiring-diagram-for-1997.html

-----------
Dash Lights And Front Marker Lights Flashing On And Off http://schematicsdiagram.blogspot.com/2012/10/dash-lights-and-front-marker-lights.html
---------- 2001 Chevrolet Tracker: Headlights and Dash lights Pulsating? http://whoisbyme.blogspot.in/2012/06/2001-chevrolet-tracker-headlights-and.html
--------- No parking lights and headlights not turning OFF? http://technoanswers.blogspot.com/2012/01/no-parking-lights-and-headlights-not.html
------------- How to replace HID headlight bulbs for lexus 400h? http://schematicsdiagram.blogspot.com/2012/01/how-to-replace-hid-headlight-bulbs-for.html
--------- Head Lights Comes ON by Itself? http://whoisbyme.blogspot.in/2012/07/head-lights-comes-on-by-itself.html
--------- Only high beams work but head lights not working on Ford F350?

http://howtobyme.blogspot.com/2011/11/only-high-beams-work-but-head-lights.html

-------------


Only high beams working on GMC Savana?---------
Working of Headlight switch?

----------
Both headlight bulbs blow together?
--------

Car headlight bulbs don't last long?


--------
How to replace Headlight Bulbs on Lincoln Town Car?

http://howtobyme.blogspot.com/2011/12/how-to-replace-headlight-bulbs-on.html


How to change headlight?

http://repairhelpcenter.blogspot.com/2011/12/how-to-change-headlight.html

-------------
Both headlights and turn signals not working? http://schematicsdiagram.blogspot.com/2011/12/both-headlights-and-turnsignals-not.html

----------
Headlights will not turn OFF on Ford expedition and car trailer?

http://technoanswers.blogspot.com/2012/01/headlights-will-not-turn-off-on-ford.html

----------
Headlight Assembly Removal on 2010 buick lacrosse? http://technoanswers.blogspot.in/2012/04/headlight-assembly-removal-on-2010.html
--------- Headlights flickering and car hesitates to start?

http://howtobyme.blogspot.in/2012/02/headlights-flickering-and-car-hesitates.html

---------
Hummers headlights flashes while start?

http://technoanswers.blogspot.in/2012/02/hummers-headlights-flashes-while-start.html

----------
Using non-AFS headlamp assembly for AFS assembly?

http://schematicsdiagram.blogspot.in/2012/02/using-non-afs-headlamp-assembly-for-afs.html

------------

How to replace Headlight Bulb on 2001 mitsubishi magna
http://www.howtorepairguide.com/2012/10/how-to-replace-headlight-bulb-on-2001.html

---------
These details will help.
Thanks.



Nov 22, 2012 | 1996 Pontiac Grand Am

1 Answer

Dirt inside my headlight


  • Open the hood of your Honda Civic, and identify the headlight assembly that has the dirt inside of it. Depending on the year of your Civic and side of the headlight, you may need to move the power steering reservoir to gain access to the light assembly.
  • 2 Squeeze the clips on both sides of the headlight assembly to release the headlight connectors. Use your fingers to loosen the headlight, and pull the small plastic tab to loosen the rubber gasket from the frame.
  • 3 Unplug the wiring harness from the back of the bulb. Twist the bulb, to remove it from the headlamp assembly.
  • 4 Locate, and remove, the screws that hold the headlight casing in place. Once the screws have been removed, gently guide the headlight casing from the location.
  • 5 Inspect the assembly under a bright light, identifying any cracks that may be in the casing. If there is a crack, use a silicone sealant to seal the crack.
  • 6 Dry the assembly, using a towel and or hairdryer.
  • 7 Replace the assembly back into your Honda Civic, and secure it by replacing the screws you removed.
  • 8 Replace the rear gasket where the bulb is inserted with a new gasket. Insert the bulb, and twist it into place.
  • 9 Reattach the bulb wiring harness.
  • 10 Turn the lights on, and re-aim the light assembly. good job your done

  • Dec 18, 2010 | 2004 Honda Civic

    2 Answers

    Honda accord repair manual


    The closest discount auto store should have it, or Haynes.com at this link http://www.haynes.com/products/productID/194

    Mar 13, 2010 | 2000 Honda Accord

    1 Answer

    Have a 2000 honda accord sedan. need to know


    Pop open the left side and follow the same pattern. ;o)

    Sep 15, 2009 | 2000 Honda Accord

    2 Answers

    Headlight lens removal


    Open hood and look at top back of the assembly and you will see 2 clips. Pull them up and remove,then release the lower clip and pull assembly out.

    Apr 08, 2009 | 2000 Ford F250 Super Duty Crew Cabs

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    29 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Honda Experts

    Marvin
    Marvin

    Level 3 Expert

    85239 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    14852 Answers

    Vincent G
    Vincent G

    Level 3 Expert

    2363 Answers

    Are you a Honda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...