Question about 2010 GMC Sierra 1500

1 Answer

2010 gmc 1500 padlock on dash turn key on for 10 min then turn off for 2 min still will not start disconnect battery then hook back horn activate use key to turn it off

No line under P R D D M just won't turn over can it be the silinoted

Posted by Richard Wilson on

Ad

1 Answer

Jeff Armer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 1,932 Answers

Can it be the silinoted ???? Solenoid is the correct spelling . Your best bet , have it towed to a qualified repair shop . This is a computer problem , not the solenoid . The padlock light lit , anti-theft system problem , more then likely . Guessing is not the way to fix this . Hooking up a factory or some other professional type scan tool an checking code's in the anti-theft module an the ECM - engine control module . Your 10 min. key off an wait 2 min won't work on your vehicle . You need a factory scan tool to do a reset
10-Minute Immobilizer Relearn
This 10-minute relearn procedure will relearn the prerelease password and the challenge/response data between the theft deterrent module (TDM) and the engine control module (ECM).
Connect a scan tool to the vehicle in the pass-thru arrangement.
Turn ON the ignition, with the engine OFF.
Ensure that all power consuming devices are turned OFF on the vehicle.
On the Techline Terminal, select Service Programming System and follow the Techline Terminal on-screen instructions, using the Pass-Thru method. Ensure the correct programming selection is chosen based on component being replaced or programmed. For this procedure, go to the V.T.D. Vehicle Theft Deterrent Learn menu and choose the Vehicle Theft Deterrent Learn, ECM, or PK3 Replaced selection.
At this point the scan tool must remain connected for the duration of the 10-minute relearn procedure.
Important:
• The scan tool will initially display 12 Minutes. The first 2 minutes allow the scan tool to initialize the appropriate control module. The remaining 10 minutes is the relearn timer.
• On some vehicles the security indicator may be illuminated for the duration of the 10-minute relearn procedure.
Observe the scan tool, after approximately 10 minutes the scan tool will display "Programming Successful, Turn OFF Ignition". The vehicle is now ready to relearn the key information and/or the passwords on the next ignition switch transition from OFF to CRANK.
Turn OFF the ignition and wait 2 minutes.
With a master vehicle key, turn the ignition to the RUN position for 15 seconds, then start the vehicle. The TDM and ECM have now relearned the pre-release password and the challenge/response data.
With a scan tool, clear any DTCs.



Circuit Description (Key Start)
When the ignition switch is placed in the Start position, a discrete 12-volt signal is supplied to the body control module (BCM) notifying it that the ignition is in the Start position. The BCM then sends a message to the engine control module (ECM) notifying it that CRANK has been requested. The ECM verifies that the transmission is in Park or Neutral. If it is, the ECM then supplies 12 volts to the control circuit of the crank relay. When this occurs, battery positive voltage is supplied through the switch side of the crank relay to the S terminal of the starter solenoid.

The easiest way to check to see if this is all correct ,is by hooking up a scan tool an viewing data parameters .
The immobilizer system functions are provided by the theft deterrent module (TDM) and the engine control module (ECM). When an ignition key is inserted into the ignition lock cylinder and the ignition is switched ON, the transponder embedded in the head of the key is energized by the exciter coil surrounding the ignition lock cylinder. This exciter coil is part of the TDM. The energized transponder transmits a signal that contains its unique value, which is received by the TDM. The TDM then compares this value to a value stored in memory. If the values match, the TDM will send the prerelease password via the serial data circuit to the ECM. If the transponders unique value is incorrect, the TDM will send the fuel disable password to the ECM.
When the ECM receives the TDM prerelease password, the ECM will challenge the password. The ECM sends this challenge back to the TDM via the serial data circuit. Both the ECM and TDM perform a calculation on this challenge. If the calculated response from the TDM equals the calculation performed by the ECM, the ECM will allow vehicle starting.
The components of the theft system are as follows:
• TDM
• ECM
• Ignition key (Transponder)
• Security indicator

Your best bet , i say again , is have a professional technician sort it out . Or you'll waste your money buying parts your don't need .

Posted on May 25, 2019

Ad

5 Related Answers

countrysi248

Jerry Koski

  • 443 Answers

SOURCE: flashing security light in dash

pontiacs have a security key do you have another key you can try to make sure this is not the problem ?

Posted on Jan 25, 2009

Ad
shadtremonky

gerald darling

  • 353 Answers

SOURCE: i have a 1999 Gmc Jimmy and i think that i have

cycle key on/off 4 times, but don't start

Posted on Jul 05, 2009

kirtec auto

  • 1348 Answers

SOURCE: Engine won't start. Dash lights flash rapidly when key turned.

the battery says 12 volts but may be dropping to 4 or 5 under a load...i would suggest jumpstarting the car and see what happens.the battery should read in the high 12 volts and not less than 9.5 under cranking. the dash lights go out on your car when starting,and the alarm will go off ,and disable the ignition if the voltage is too low in cranking the car because the computer will shut it down and activate the anti theft.....check your battery posts are tight. best of luck

Posted on Jul 22, 2009

Anonymous

  • 2 Answers

SOURCE: car wouldn't start. jump started let run 10 min

get a better ******* car, daewoos **** ***

Posted on Oct 31, 2009

Anonymous

  • 212 Answers

SOURCE: 1999 GMC Savana 1500 5.7 L V8 won't start. It

CHECK TO SEE IF FUEL PUMP IS COMMING ON WHEN YOU TURN KEY ON.

Posted on Feb 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Getting spark fuel but won t start


If it is a fuel line you would smell and see gas drip where you park most likely, unless it is up over frame and drying prior to hitting the ground which is possible. Smell gas while parked? Get up under it and look for wet spots on fuel line. Are you getting fuel through line? Pull from under hood and check pressure.

Mar 03, 2014 | GMC Suburban Cars & Trucks

1 Answer

Grounded out wires and it won't crank over


A/T or M/T transmission, they are wired diffr.!
I guess, you know flashing is bad wiring , right?

but this no crank page solves this.
takes only $20 voltmeter to be , effective.

to crank takes but 1 wire. (starter good)
the ST line or start line.
suzuki calls this 1 wire the Start line, (amazing fact)
at the key switch a black-red wire.
then after passing through the (clutch/ or A/T park switch)
the color changes, 1 time to blk-yell, then lands on the starter.
its very simple and fully show here, in details.

http://www.fixkick.com/nocrank.html

Mar 31, 2013 | 1994 Geo Tracker

1 Answer

I just put a new battery in my 1995 buick lesabre But It won't start. It turns over great but it won't fire up. Is there a fuse Ior a circuit breaker somewhere under the hood I checked the fus


there should be an ignition fuse in the fuse panel that mite be it
also you need to make sure it is gettin fuel and fire to narrow the problem
down . how long has the car been sitting ?

Feb 16, 2013 | 1995 Buick LeSabre

1 Answer

Car won't start when cold, Volkswagen passat


check battery and battery connection,fuel filter,air filter.

Feb 16, 2013 | Cars & Trucks

1 Answer

My nissan patrol 88 gq won't start after sitting


there is a filter in the injector pump, under the inlet line. could be blocked.

also try cracking the injector line and cranking the car to bleed the lines.

Sep 30, 2012 | Cars & Trucks

1 Answer

Fuel pump issues, car won't start, but cranks. I want to know where the fuel pump is and how I can see if it is working properly. How do you diagnose the fuel system issues.


the fuel pump is located in the fuel tank.

I assume you don't have a fuel pressure gauge so the first thing you can do is climb under the vehicle and disconnect the plastic fuel line where it connects to the metal line about in the center of the van up where the front seats would be. Have a drain pan under this area to catch any fuel and be ready to be sprayed if there is fuel pressure in the line. Safety glasses would be a good idea and you can wrap a rag around the line right before you fully disconnect the two lines to help avoid spraying gas everywhere.

keep the drain pan under the area of the disconnected line. Turn the key on but do not start the vehicle. You should see gas spray out of the plastic line. If you don't you're on the right track.

If there is no fuel, reconnect the lines and look back by the fuel tank. You will see the harness. find the dark green with white wire. It is the power supply to the fuel pump. Check for power on that wire. If you have power than you have a bad pump.

If you have any questions let me know. Thank you for using Fixya.com!

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Oct 14, 2011 | 1999 Plymouth Voyager

1 Answer

Won't start after short trip like its vaper locked


STARTING / IDLING PROBLEMS / MISSING

Your problem may be one of the following:
First check or just replace the fuel filter. Usually located under the car in front of the rear axle, drivers side.
Next, the fuel pump may be worn out. Usually they just stop working (running).
Next, check the fuel pressure regulator. Usually located on the front fuel rail, drivers side.
Is the vacuum line attached? Not leaking or rotted?
Also, do you smell a strong fuel odor when it won't start? May be one or more stuck-open injectors, or the coil pack is bad.
Checking these in the order listed will more than likely fix your problem.
The clicking noise indicates the battery can no longer run the starter, which also means the fuel pump won't run either.

It could be a fuel issue. How old is the fuel filter? Can you hear the pump run for a few seconds when you turn the key on? Try turning the key to ON without trying to start engine three times waiting for the pump to stop running each time. Then try to start the engine. If it starts, Its a form of Vapor lock caused by the extreme heat we have had lately.

If none of this works, try a new fuel filter first. From there have someone check the fuel pressure regulator and then the pump. If you are in need of a new pump, take my word for it and spend the money to get one from FORD, and not from your favorite parts store. Most parts store parts are made in China and they are JUNK.

Have you hooked a scanner to the computer and checked the oxygen sensor(s)? If they are bad they could lean out the engine.

VAPOR LOCK
Check the following:
Cooling system working properly including fans.
Under hood fuel lines touching coolant or heater hoses.
Fuel lines under vehicle close to or not shielded from exhaust pipe, converter, muffler. Fuel lines pinched or crushed.
Fuel filter changed recently.
Fuel pump pressure.
Cheap(Bad) gas.

Aug 26, 2011 | 2003 Ford Taurus

1 Answer

My dodge dakota truck will not start. It has power we tried to pop the clutch too.


do you mean the truck won`t start and run or do you mean it won`t turn over with the key.if it won`t turn over with the key the you may have a starter problem.if you mean won`t start then it could be the fuel pump not working.with someone cranking the motor you should hear the fuel pump running with the gas cap off and listening at the filler neck.or hear it running listening under the truck at the gas tank.if you don`t hear it then you can hit the tack sharply with your hand or a rubber hammer,it hear the pump start to run then the fuel pump needs replacing.if not check the fuses under the dash and under the hood.if they are good then it may be the pump relay in the relay box under the hood and it should be marked on the box or lid.

Apr 16, 2011 | 2000 Dodge Dakota Quad Cab

1 Answer

Vr4 won,t start was going an is turning over


It may not be getting fuel. You have to maybe look to changing the inline fuel filter or have the fuel pump itself checked for operation. The fuel pump is in the gas tank, but you can check fuel flow by separating the line at where it goes into the injectors. Put a plastic container under the line where separated and crank the engine a couple times and see if you have fuel flow. Often times the inline fuel filter gets gunked up by sediment from the gas tank and blocks fuel flow.

Mar 24, 2011 | 2001 Ford Explorer Sport

Not finding what you are looking for?
2010 GMC Sierra 1500 Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...