Question about Citroen Cars & Trucks

Open Question

I have a 1988 2CV. Indicators not working. They did work but no longer. Fuses ok. all wires appear to be ok. Did get the wipes and brake lights working again.

Posted by Helen Coates on


5 Related Answers



  • 166 Answers

SOURCE: Vauxhall/Opel frontera indicators not working

thats a relay thats is not working propperly, must be replaced to fix the problem, just go to your dealiship and ask for a turn indicator relay for your model and ask your part sales man to show you where is located, if not...just follow that click...
have fun

Posted on Aug 21, 2009



  • 1986 Answers

SOURCE: The brake lights and 3rd brake stopped working.

Look above your brake pedal and you will see your brake switch up along your brake pedal arm. It will either be between the brake arm and the firewall so when you brake it pushes the switch in. Or it will be between the dash and the brake arm so when you brake it pulls the switch out. Most likely this switch needs to be replaced

Posted on Oct 19, 2009



  • 65 Answers

SOURCE: vw passat 02 1.9 tdi brake lights not working


Posted on Feb 28, 2010


frank thomas wilson

  • 10319 Answers

SOURCE: wiring diagram for 1996 gmc sierra brake asembly

The brake light switch is at fault. Get a new one and replace it. The location is at the brake pedal area mounted on a bracket with a plunger stud that rest on the brake pedal's arm the pad is attached to

Posted on May 08, 2010


Brad Kirby

  • 547 Answers

SOURCE: My daughters hyundai accent 2000

Do the blinkers work? If the same bulbs work as brake lights also work as blinkers, the wires for them are routed through the turn signal switch. If that switch is bad, you won't have brake lights.

Posted on Dec 05, 2010

Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

No Tail Lights Working

You probably pinched a wire when you put the bed back on. You most likely have a blown fuse as further proof that you shorted out everything in the back of the truck.
Recheck all your wiring paths.

Jan 12, 2018 | Ford F-150 Cars & Trucks

1 Answer

The rear brake lights or indicators dont work on my holden astra

Make sure all the wires are pluged into the light fixtures and that there not corroded

May 30, 2012 | Cars & Trucks

1 Answer

I have a v6 1996 ford mustang everything are working well,head lights and park lights. but my problem are brake light and right & left turn signal are not working? thanks!

ok iam in spain and we use a different wiring circuit for indicators and brake lights ,now you vehicle has a special stop light switch that interferes with the indicators as and when the brake lights are applied ,so you use the stop lights which also work as indicators ,compared to europeon laws which require seperate indicators ,noy the problem you describe is common with american vehicles and the main cause is the fancy stop light switch they use

Sep 06, 2010 | Ford Mustang Cars & Trucks

1 Answer

Blowing brake light fuses 1988 E150. Brake switch

To Track down the problem you need to disconnect the Battery and use a Multimeter set to OHMS.

You are grounding somewhere. Start with the Brake switch and see if it is grounded. Then take off the wires to the switch. Check the wires going to the switch and coming from the switch. One side has to be the problem. Check with a parts place like Autozone or Oreillys for a Brake relay in the power box. If the power wire is grounded unplug the Brake relay and see if it drops the connection.

If it is a wire problem, keep tracing the grounded wire until you find a connection you can unplug to make the Ohmmeter drop. Remember the overhead Brake light on the roof. You may have just worked on the Taillights. The bad wire may be grounding in the roof or on the frame.

Once you isolate the bad wire you may want to run a new one.

Jul 04, 2010 | 1988 Ford Econoline

1 Answer

2005 grand cherokee brake lights out. changed bulbs didnt work. third brake light is working checked fuses ok .

checked all fuses even under hood? may have bad signal switch or bad brake light switch yes even if 3rd brake works.also check wiring under rear fender by bumper thats were wire harness is hope this helps.

Oct 09, 2009 | 2005 Jeep Grand Cherokee

2 Answers

My car brakes become spongy after starting the

check rear brakes for leaks could be leaking wheel cylinder

Jul 11, 2009 | 2006 Fiat 124

4 Answers

Brake lights on 306 TDi not working, bulbs and fuses ok

hi don,t usually have relays on brake lights check your brake light switch take the wires off the switch connect together with the ignition on see if the lights come on they should yates210456

Oct 09, 2008 | 1989 Peugeot 405

1 Answer

Brake Light Problem


Often brake lights and signal lights not working indicates a loose grounding of the rear electrical assembly. Other indicators would be dim and/or all the lights light up (but dimly) when engaging the breaks or activating any of the turn indicators. A way to verify this is to hardwire another/external grounding wire to any of the metal receptacles of the bulbs straight to a bare metal/chassis of the vehicle.

Of course the standard procedure of checking the fuses, the harness connectors and the wire harness themselves still apply.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Jun 27, 2008 | 1999 Chevrolet C/K 2500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Citroen Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14847 Answers

Are you a Citroen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides