At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
Filter is located behind fuel tank, some were a quick connect style and most invoved a fitting on each end. Look carefully at new filter. Sometimes the fittings rust to the line, use a penetrant. If you can loosen and disconnect at least one fitting, sometimes you can spin off the filter without freeing up the fitting on the other side.
To check injector pulse, you need 2 people. One is to crank the engine. The other is to watch the voltmeter connecting to the plug delivering the electrical signal to an injector. If during a period of cranking, there is no voltage displayed that means there is no injector pulse. Here is an image of connector port going into the injector to open its valve as needed.
Ignition Lock Cylinder CAUTION If the car is equipped with an air bag, do not service the steering column or dashboard components. Extreme danger of air bag deployment exists even with the battery removed! Serious injury could occur.
REMOVAL & INSTALLATION
Without Air Bag
Place the ignition switch in the RUN position.
Remove the lockplate, turn signal switch and buzzer switch.
Remove the screw and lock cylinder.
NOTE: If the screw is dropped on removal, it could fall into the column, requiring complete disassembly to retrieve the screw. To install:
Rotate the cylinder clockwise to align cylinder key with the keyway in the housing.
Push the lock all the way in.
Install the screw. Tighten the screw to 14 inch lbs. (2 Nm) for adjustable columns and 25 inch lbs. (3 Nm) for standard columns.
With Air Bag CAUTION Before proceeding, refer to Section 6 for information on disabling and enabling the SIR (air bag) system; otherwise, serious injury could occur.
Turn the steering wheel so the vehicles wheels are pointed straight ahead.
Place the ignition switch into the LOCK position to prevent undercentering of the coil assembly.
Disable the SIR system. Disconnect the negative battery cable.
Remove the coil assembly retaining ring, then disconnect the inflatable restraint coil assembly. Let the switch hang freely if removal is not needed. To remove the coil assembly proceed.
Remove the wave washer, then the shaft retaining lock ring with tool J-23653-SIR to push down on the shaft lock. Dispose of the ring, it is not reusable.
Fig. 1: Special tool J-23653-SIR or equivalent is required for pushing down the shaft lock to remove the shaft ring
Remove the shaft lock, then disconnect the canceling cam assembly.
Remove the upper bearing spring, race seat and race.
Position the turn signal to the right turn (up) position.
Remove the multi-function lever and hazard knob assembly. Unfasten the round washer head screw and signal switch arm, along with the turn signal switch screws.
Remove the turn signal switch assembly by unfastening the connector from the bulkhead connector. Gently pull on the harness through the column and disconnect.
Make sure the coil assembly does not become uncentered, this could happen if the centering spring is pushed down letting the hub rotate while the coil is removed from the steering column.
Remove the inflatable restraint coil assembly with the wiring harness from the column assembly.
Remove the wire protector, then attach a length of mechanics wire to the coil terminal connector to aid in reassembly. Then gently pull the wire through the column.
Remove the key from the steering column lock cylinder set, then remove the buzzer switch assembly.
Reinsert the key into the lock cylinder, turn it to the LOCK position.
Remove the lock retaining screw, then the cylinder.
To install:NOTE: Make sure all fasteners are securely seated before applying the necessary torque. If you fail to do so, component damage or malfunctioning of the steering column may occur.
Install the lock cylinder assembly, insert the retaining screw, then tighten to 22 inch lbs. (2.5 Nm).
Insert the key into the lock cylinder. Install the buzzer switch assembly. Turn the key to the LOCK position.
Install the turn signal switch assembly wiring harness through the column, let the switch hang freely. Connect the wiring to the bulkhead.
Insert the coil assembly wiring harness through the column letting the coil hang freely. Attach the turn signal assembly with the binding head screws. Tighten the screws to 30 inch lbs. (3 Nm).
Attach the signal switch arm with the round washer head screw, tighten the screw to 20 inch lbs. (2 Nm).
Install the hazard knob assembly and the multi-function lever.
Install the inner race, upper bearing race seat and spring. Attach the turn signal cancelling cam assembly, apply grease for lubrication.
Replace the shaft lock and install a new shaft lock retaining ring. Use tool J-23653–SIR or equivalent to push down on the shaft lock. The ring must be firmly seated in the groove on the shaft.
NOTE: Set the steering shaft so that the block tooth on the race and upper shaft is at the 12 o'clock position. The wheel on the car should be straight ahead. Set the ignition switch to the LOCK position, as this will ensure no damage to the coil assembly.
Install the wave washer, then attach the coil assembly, make sure it is centered correctly.
Fig. 2: Centering the coil assembly is important in assembling the column assembly
Attach the coil assembly retaining ring, the ring must be firmly seated in the groove on the shaft.
Gently pull the lower coil assembly, turn signal, and pivot (pulse) wires to remove any kinks that may be inside the steering column assembly. If you fail to do this you can damage the wiring.
Complete assembling the steering column assembly.
Attach the negative battery cable.
Check the functions of the turn signal, make sure it cancels when turned on and the steering wheel is turned.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Stick your car details onto youtube. there's all sorts of info like this question on there. basically its low down on the right front engine block as you look in.
Filter is located behind fuel tank, some were a quick connect style and most invoved a fitting on each end. Look carefully at new filter. Sometimes the fittings rust to the line, use a penetrant. If you can loosen and disconnect at least one fitting, sometimes you can spin off the filter without freeing up the fitting on the other side.
i was just dealing with the same problem check out your fuel injectors , fuel pump, ingnition module with coil overs and possible fuel filter mine was the pump injectors and module its also a 93 cutlass ciera 3.3 fuel inj. hope this helps
×