Question about Nissan Cars & Trucks
WHEN YOU STAND ON THE FRONT OF THE CAR YOU ONE IS RIGHT BELOW OF THE INTAKE WHICH IS BANK 2 OR THE ONE CLOSE TO FIREWALL , BANK 1 ONE IS ON SAME SIDE NEXT TO THE RADIATOR BUT THEY BOTH ON THE CAM RIGHT SIDE OF THE ENGINE, THE EASIEST WAY TO IDENTIFY THEM IS THAT THEIR CONNECTOR IS GREEN, ONCE YOU LOCATE THEM THE CLIP NEEDS TO BE PUSHED DOWN TOWARD THE SENSOR FOR THE CONNECTOR TO BE RELEASED, ONCE YOU REMOVE THE CONNECTOR THERE WILL BE ONLY A 10MM SCREW HOLDING THE SENSOR PULL IT OUT , THE SAME SETTING THE NEW ONE PUSH IT ALL THE WAY IN , THIGHT THE 10MM SCREW, CONNECT IT BACK AND YOU'RE DONE,BUT FOR THE ONE ON THE BACK SOMETIMES MIGHT BE NECESARY FOR YOU TO TAKE THE INTAKE OFF....HOPEFULLY IS NOT YOUR CASE....
Good luck!!! and if you need the crank for hard starting on hot/warm, it is located on the botton middle section on the transmission is the only cable that goes down to a small piece of metal and it is held by a 10mm screw only to protect the sensor, you will se the sensor once you remove that small about 6-8 inches piece of metal. Then you'll be able to unescrew the 10mm screw that holds the crank position sensor. when you pull it off you'll be able to see the fly wheel inside the transmission...
you all enjoy your rides out htere!!!
Posted on Jul 01, 2009
SOURCE: maxima 2006 drive belt
First, keep this link which is to the diagram of the serpentine belt. It will be useful in knowing how to route th new belt...
Next, here's a link to a good video on how to replace a serpentine belt...
Posted on Sep 12, 2009
The first thought that comes to mind is a high pressure oil leak. The
injectors have a snap ring on top that sometimes becomes detached and
it will create these symptoms.
When you depress the brake it sends a signal to the PCM (Powertrain Control Module) and the PCM increases the idle because it predicts you are about to shift into gear. If the truck has a high pressure leak inside the engine it will have a hard time building pressure initially and once the oil warms and thins out the High Pressure Oil Pump cannot hold the pressure and the oil leaks faster because it is thinner.
You may have a leak around the pump area which is under the turbo also. The IPR which is the regulator that controls the oil pressure may also be bad. It is directly under the turbo as well. The IPR is located under the turbo on the High Pressure Oil Pump cover. You stated the seals were leaking on the IPR itself? If the orings are damaged or if the screen in the end of it is collapsed or even punched through with a small hole it will need replaced. Screen damage is usually a sign of debris entering it from either dirt from a previous repair or something is coming apart inside.
Make certain you have clean oil and fuel filters. Yor may want to check fuel pressure as well. It should be somewhere around 55psi on acceleration.
Additionally, I suggest check for voltage at the connector on the fuel pump. The pump is mounted in the filter housing on the frame and the connector is at the front of it. The pink and black wire should have 12 volts with the key on for about 30 seconds. If the pump has voltage but is not running, then your pump has failed. If there is no voltage then check fuse 2.40 in the central junction box. This is the fuse that feeds the inertia switch through the fuel pump relay. I have included a fuse box layout and a wiring diagram (click over images for zoom)...
Additionally, will need to scanned the PCM to know if some fault code is stored there.
Keep us updated.
Posted on Oct 08, 2011
Tips for a great answer:
Dec 13, 2015 | 2006 Nissan Sentra
Feb 24, 2014 | 2006 Nissan Maxima
Feb 22, 2013 | Nissan Altima Cars & Trucks
Jun 06, 2011 | 2004 Nissan Maxima
Mar 21, 2010 | 2007 Nissan Maxima 3.5 Sl Sedan
Jul 11, 2009 | 2000 Mercury Villager
Oct 03, 2008 | 2000 Nissan Maxima
Aug 09, 2008 | 2003 Nissan Maxima
May 29, 2020 | Nissan Cars & Trucks
48 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: