Question about Isuzu Cars & Trucks

1 Answer

Trying to program my 5bcr07 remote start feature.. i can't find help anywhere. i have a 2003 isuzu rodeo and the prestige alarm model is APS996A.

The feature worked with the original key fob, but i can't figure out how to program it to this new one...

Posted by Michael Keith on

Ad

1 Answer

k spencer

  • Level 1:

    An expert who has achieved level 1.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 17 Answers

OPEN Driver’s door and INSERT key into the Ignition.TURN the Ignition to ACC (one turn back towards you) and then to the LOCK position three (3) times within three (3) seconds.Within 10 seconds, CLOSE and OPEN the Driver’s door twice (2).AGAIN, TURN the Ignition to ACC and then to the LOCK position three (3) times within three (3) seconds.AGAIN, within 10 seconds, CLOSE and OPEN the Driver’s door once (1). The vehicle will respond by cycling the locks indicating that the vehicle has entered Programming Mode.Within 20 seconds, PRESS the LOCK Button on the remote to be programmed. The vehicle will respond by cycling the locks.Within 20 seconds, PRESS the UNLOCK Button on the remote to be programmed. The vehicle will respond by cycling the locks signalling successful programming of the remote.REPEAT Steps 7 and 8 for each additional remote to be programmed to the vehicle.REMOVE the key from the Ignition to exit Programming Mode.Test all remotes. Programming is now complete.If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same. Hope this helps . K S

Posted on Apr 01, 2019

Ad

5 Related Answers

j_del

Jeremy Dellow

  • 1586 Answers

SOURCE: central locking system stopped working

If the A6 layout for the modules is the same as my A4, the lock pump is in the rear corner of the car, on the passenger side. In the trunk, pull up the carpeting behind the passenger rear wheel, and tucked down in there is the pump assembly. They're known to go bad and it's a pretty likely cause for your problem, provided your fuses are not blown.

Posted on Aug 08, 2008

Ad

Anonymous

  • 11 Answers

SOURCE: Remote Keyless Entry fob for my 2007 Suzuki XL7

Not 100% sure about Suzukis but on my ford the same happened to me and I had to program them at the same time. Hopefully this helps.

Posted on Jan 19, 2009

Anonymous

  • 150 Answers

SOURCE: Programming a key fob

you will need the dealership diagnostic tool to program the remote

Posted on Apr 24, 2009

Anonymous

  • 52 Answers

SOURCE: 2003 Jaguar S-Type, programming a key fob

If its a new key fob the only way you can program it is this the factory scan tool, u'll have to take it to a dealership for them to do this and they will charge you .5 hrs for labor.only x-types can be programmed without the jaguar software. Im guessing it will cost you between 40 and 50 bucks to have them program it.

Posted on May 11, 2009

Anonymous

  • 508 Answers

SOURCE: key fob needs programming

call 509-456-7890 they maybe able to help!!!

Posted on Jun 22, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

KEY FOB NOT DETECTED DODGE CHALLENGER


Hi Fred,
There could be a number of reasons for this.

As I do not have much detail and do not know your knowledge of cars, I will explain the basic principle at work here and hopefully that might give you a clue as to what the problem might be:

In all modern cars the key fob (plastic part of the key) has a coded electronic chip moulded inside. There is a sensor just under the steering column cover, usually right next to the ignition switch. This sensor activates whenever a key is turned in the ignition switch and the sensor reads code stored in the chip in the key fob.

When all is good, the engine will start as expected as the keys code will have been programmed into the cars engine management control system and the key is recognised as a matching/authorised key. No match, the engine won't start - a very good safety feature.

Some reasons why this may give the fault you are experiencing:
  • You bought a replacement key from the Dodge Dealer, but the new key has either not been programmed into the cars engine management system or the programming was not successful
  • You bought a non-chipped key from a non-dealer and had it cut from the original, but were not aware of the need for a chipped key and the need to have the new key programmed into the management system. A non-chipped key will not work, ever unless the management system is compromised
  • There may be a fault with the sensor
  • Very unusual, but the chip in the key may have been damaged
Do you have an original spare key to try?

Hope this sheds some light on your problem :)

Ian Reid

Oct 28, 2017 | Dodge Cars & Trucks

3 Answers

I lost remote to my 2007 corolla how do i get a new one if i am not the original buyer


go to any Toyota dealer. They will sell you a new key fob but they also charge extra for programming. Total cost for the key fob and programming will be around $100. any Toyota dealer can do it for you

Apr 02, 2015 | 2007 Toyota Corolla

1 Answer

Programing key fob on 2004 chrysler sebring convertible without the original


programming key fobs is best done with the vehicle connected as well
take it to a service dealer who has the gear to program the key and the immobiliser at the same time

Mar 25, 2015 | 2004 Chrysler Sebring Convertible

1 Answer

I have a Toyota Avensis 2007 1.6 and I want to know if my car have any feature with the key fob like open the windows with the key fob or any other feature! Thank you :)


I find the toyota owners forum very helpful on these type questions:
Programming Avensis T3 Key Fob Avensis Club

Unfortunately it doesn't look like there are any special features, most of the entries revolve around reprogramming if you have to replace or renew the batteries.

Jan 02, 2015 | 2007 Toyota avensis 1.6

1 Answer

Ford focus 2001 1.4cl key fob not working


Is it your original key fob or a new one?

Jun 26, 2013 | Cars & Trucks

1 Answer

Got new key fob for my 2006 chevy malibu ss how do I program it to work


How to Program a Key FOB for the Chevy ' eHow.com

www.ehow.com/how_7508133_program-key-fob-chevy.html

How to Program a Key FOB for the Chevy ... your Chevy, if you obtain new or replacement keys they will need programming to work with ... How Do I Program MyKey Fob? ...

Mar 14, 2013 | Cars & Trucks

1 Answer

What caused my '05 mazda 6 key fobs to stop working


Loss of programming maybe or a faulty keyless entry module.

Nov 01, 2012 | 2005 Mazda 6

2 Answers

How do i program my ford key fob 2 my transit van


1 - Unlock the doors. Put the key in the ignition, and turn from "Off" to "ACC" 8 (eight) times in under 10 seconds. The doors will lock. Leave key in the "ON" position

2 - Program the fobs by pressing any key on the fob. The doors locks will lock/unlock

3 -- Turn the key to Off. Locks will lock/unlock, and you are out of programming mode.

I bought new remote Key Fob on Ebay and it did work properly on my Ford Transit LWB 2003. Good Luck!

Mar 22, 2012 | Cars & Trucks

2 Answers

My key fobs for my 2007 gmc sierra classic body will not reprogram. One is a new fob only a few months old and the other is original. i replaced the batteries and did every step to reprogram it, and...


Unless I am mistaken (and it is possible), you typically must have two (2) working original key fobs to program a third.

Is your original not working either? Any custom work to the vehicle recently?

Feb 23, 2018 | GMC Sierra 1500 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14850 Answers

Mike

Level 3 Expert

4369 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...